• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.314-322
• /
• 2003

Pipe cooling method is widely used for reduction of hydration heat and control of cracking in mass concrete structures. However, in order to effectively apply pipe cooling systems to concrete structures, the coefficient of flow convection relating the thermal transfer between inner stream of pipe and concrete must be estimated. In this study, a device measuring the coefficient of flow convection was developed. Since a variation of thermal distribution caused by pipe cooling has a direct effect on internal forced flows, the developed testing device is based on the internal forced flow concept. Influencing factors on the coefficient of flow convection are mainly flow velocity, pipe diameter and thickness, and pipe material. Using experimental results from the developed device, the coefficient of flow convection was calculated. Finally, a general prediction model was proposed by theoretical procedures. The proposed prediction model is able to estimate the coefficient of flow convection with flow velocity and material properties of pipe. From comparison with experimental results, the coefficient of flow convection by this model was well agreed with those by experimental results.

• Journal of the Korean Geographical Society
• /
• v.42 no.6
• /
• pp.898-913
• /
• 2007

We examined soil properties and provenance of loess-paleosol sequences at the Daebo Granite area of Buan, Jeonbuk Province, South Korea. The section consists of the surface layer, Layer 1(paleosol), Layer 2(loess), Layer 3(paleosol), Layer 4(loess), and Layer 5(paleosol), from top to bottom and thickness of the exposed section is approximately 280cm. The magnetic susceptibility values show the distinct variations between the loess- and the paleosol layer. Even though pH, ORP, water content, and soil hardness do not display the obvious differences in the section, the organic content indicates the variation similar to those of the magnetic susceptibility. In the respect of the soil colors measured under 3 conditions, although the variations of the wet soil color exceedingly reflect the difference of the layers, these variations are obscure in some points in the section due to the characteristics of the Munsell color system. Based on the geomorphological properties, sedimentary structure, the difference of the major element composition and the condrite-normalized rare earth element(REE) patterns showing the clear difference from the adjacent bedrocks and stream sediments and the similarity to those of the Chinese Loess Plateau, it is suggested that the section was formed by the material originated from the Chinese Loess Plateau and peripheral areas. However, because the material experienced the alteration after sedimentation under the environment of the sediment area, it has the properties different from the material in the provenance areas. This phenomenon may result in the climatic condition of Korea, especially in precipitation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.276-276
• /
• 2010

Localized surface plasmon resonance (LSPR) has been explored recently as a promising approach to increase energy conversion efficiency in photovoltaic devices, particularly for thin film hydrogenated amorphous silicon (a-Si:H) solar cells. The LSPR is frequently excited via an electromagnetic (EM) radiation in proximate metallic nanostructures and its primary con sequences are selective photon extinction and local EM enhancement which gives rise to improved photogeneration of electron-hole (e-h) pairs, and consequently increases photocurrent. In this work, high-dielectric-constant (k) $ZrO_2$ (refractive index n=2.22, dielectric constant $\varepsilon=4.93$ at the wavelength of 550 nm) is proposed as spacing layer to enhance the LSPR for application to the thin film silicon solar cells. Compared to excitation of the LSPR using $SiO_2$ (n=1.46, $\varepsilon=2.13$ at the wavelength of 546.1 nm) spacing layer with Au nanoparticles of the radius of 45nm, that using $ZrO_2$ dielectric shows the advantages of(i) ~2.5 times greater polarizability, (ii) ~3.5 times larger scattering cross-section and ~1.5 times larger absorption cross-section, (iii) 4.5% higher transmission coefficient of the same thickness and (iv) 7.8% greater transmitted electric filed intensity at the same depth. All those results are calculated by Mie theory and Fresnel equations, and simulated by finite-difference time-domain (FDTD) calculations with proper boundary conditions. Red-shifting of the LSPR wavelength using high-k $ZrO_2$ dielectric is also observed according to location of the peak and this is consistent with the other's report. Finally, our experimental results show that variation of short-circuit current density ($J_{sc}$) of the LSPR enhanced a-Si:H solar cell by using the $ZrO_2$ spacing layer is 45.4% higher than that using the $SiO_2$ spacing layer, supporting our calculation and theory.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5542-5550
• /
• 2012

Third-order shear deformation theory is reformulated using the nonlocal elasticity of Eringen. The equation of equilibrium of the nonlocal elasticity are derived. This theory has ability to capture the both small scale effects and quadratic variation of shear strain through the plate thickness. Navier's method has been used to solve the governing equations for all edges simply supported boundary conditions. Analytical solutions of buckling of nano-scale plates are presented using this theory to illustrate the effect of nonlocal theory on buckling load of the nano-scale plates. The relations between nonlocal third-order and local theories are discussed by numerical results. Further, effects of (i) length (ii) nonlocal parameter, (iii) aspect ratio and (iv) mode number on nondimensional buckling load are studied. In order to validate the present solutions, the reference solutions are used and discussed. The present results of nano-scale plates using the nonlocal theory can provide a useful benchmark to check the accuracy of related numerical solutions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.5
• /
• pp.323-334
• /
• 2020

Since boundary layer transition has a significant impact on the aero-thermodynamic performance of hypersonic flight vehicles, capability of accurate prediction of transition location is essential for design and performance analysis. In this study, γ-Re_θt model is improved to predict transition of hypersonic boundary layers and validated. A coefficient in the production term of the intermittency transport equation that affects the transition onset location is constructed and applied as a function of Mach number, wall temperature, and freestream stagnation temperature based on the similarity numerical solution of compressible boundary layer. To take into account a Mach number dependency of transition onset momentum thickness Reynolds number and transition length, additional correlation equations are determined as function of Mach number and applied to Re_θc and F_length correlations of the baseline model. The suggested model is implemented to a commercial CFD code in consideration of practical use. Analysis of hypersonic flat plate and circular cone boundary layers is carried out by using the model for validation purpose. An improvement of prediction capability with respect to variation of Mach number and unit Reynolds number is identified from the comparison with experimental data.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.5
• /
• pp.288-302
• /
• 2017

Accurate measurement of benthic nutrient fluxes (BNF) is a prerequisite for evaluating the effect of sediments on nutrient cycle in the surface water. The intact sediment cores were collected in July 2015 at the midstream of Nakdong River. We identified pre-incubation time (6, 12, 24 hr), dissolved oxygen concentration (90, 70, 50% saturation), diffusive boundary layer thickness (0, 0.6-0.8, 1.2-1.4 mm), and incubation temperature (10, 17, 20, $25^{\circ}C$) as the most important control factors, and measured the BNF fluctuation with the variation of these factors using the laboratory sediment core incubation method. Since the chemical composition, redox condition, hydrodynamic regimes and microbial activities at the sediment-water interface were changed as a result of the alteration of control factors, sediment core incubation should be conducted under as close to the natural conditions of study site as possible, in order to produce the results similar to actual values. Relative percentage differences between two replicates were below 20% in most control factors, which showed satisfactory precision for strict compliance with the experimental conditions and procedures. In the further studies, we will compare the results of core incubation with those of in situ measurements to confirm the accuracy of the sediment core incubation method.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.3
• /
• pp.292-296
• /
• 2008

Clay-coated rice seeds (clay-coated seeds A and B) were directly sown on dry paddy and their growth and yield were compared with the normal drill-sown seeds on dry flat paddy. In clay-coated seeds, germination was 1 day earlier and the emergence rate was higher up to 5% than that of normal drill-sown seeds. But the apparent number of seedling stand per $m^2$ was lower than that of normal drill-sown seeds, which is due to the smaller amount of seeding in clay-coated seeds. At the early growth stage, the plant height of clay-coated seeds A was taller than that of drill-sown seeds, while the plant height of clay-coated seeds B was 0.7 cm shorter than that of drill-sown seeds. At the late growth stage, however, the difference was insignificant in both cases. The maximum tillering stage was 10 days earlier in drill-sown seeds. Lodging index was the lowest in clay-coated seeds B and there was no difference between clay-coated seeds A and drill-sown seeds. The ratio of stem base weight, culm diameter and culm wall thickness were higher in clay-coated seeds, while the lower internodes (4th, 5th and 6th) length was shorter in claycoated seeds than in drill-sown seeds. In clay-coated seeds, the number of panicle per $m^2$ was smaller, while the number of spikelet per panicle was a little larger than in drill-sown seeds. The rate of ripened grain and brown rice 1,000 grain weight were lower in the clay-coated seeds, thus the yield was $98{\sim}99%$ level of drill-sown seeds. Considering that the amount of seeding in clay-coated seeds was two-thirds of that in drill-sown seeds, it is expected that clay coating method could become an additional technique for direct seeding cultivation.

• Korean Journal of Ecology and Environment
• /
• v.37 no.2 s.107
• /
• pp.205-212
• /
• 2004

Phosphorus cycle was studied in a deep stratified reservoir in summer monsoon area (Lake Soyang, Korea) by surveying phosphorus input from the watershed and the movement of phosphorus within the reservoir. And the spatial and temporal distribution of phosphorus was modeled with a 2-dimensional water quality model (CE-QUAL-W2), Phosphorus loading was calculated by measuring TP in the main inflowing river (the Soyang River) accounting for 90% of watershed discharge. TP of the Soyang River showed a large daily variation with the flow rate. High phosphorus loading occurred during a few episodic storm runoff laden with suspended sediments and phosphorus. Because storm runoff water on rainy days have lower temperature, it plunges into a depth of same temperature (usually below 20m depth), forming an intermediate turbidity layer with a thickness of 20 ${\sim}$ 30 m. Because of stable thermal stratification in summer the intermediate layer water of high phosphorus content was discharged from the dam through a mid-depth outlet without diffusing into epilimnion. The movement of runoff water within the reservoir, and the subsequent distribution of phosphorus were well simulated by the water quality model showing a good accuracy. The major parameter for the calibration of phosphorus cycle was a settling velocity of detritus, which was calibrated to be 0.75 m ${\cdot}$ $day^{-1}$. It is concluded that the model can be a good simulator of limnological phenomena in reservoirs of summer monsoon area.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.34 no.6
• /
• pp.348-354
• /
• 2020

Oryeong-san (ORS) is a traditional Korean herbal medicine widely used for renal associated diseases, composed of five medicine herbs; Atractylodes japonica Koidzumi, Cinnamomum cassia Presl, Polyporus umbellatus Fries, Poria cocos Wolf and Alisma orientale Juzepzuk. We studied to improve the convenience of intake and portability by developing modernized dosage forms, and examined the effect on anti-inflammation of ORS. In order to develop the tablet formulation of ORS (ORS-F), the tablets were evaluated on the basis of physical characteristics include diameter, thickness, weight variation, hardness, friability and disintegration. To analyze the marker components of ORS-F, eight index markers from five herbal medicines were chosen. And the method using high performance liquid chromatography (HPLC) with diode-array detector method was established for the simultaneous analysis. The biological activities were examined the effect of ORS-F on pro-inflammation mediated by LPS-stimulation. The production of nitric oxide (NO) and cytokines were determined by reacting cultured medium with griess reagent and enzyme-linked immunosorbent assay (ELISA). The expression of cyclooxygenase-2 (COX-2) and inducible NO synthase (iNOS) were investigated by Western blot and RT-PCR. The anti-oxidant activities of OJS-F increased markedly, in a dose-dependent manner. and, The total phenolic compound and flavonoids contents of OJS-F were 10.20±0.09 ㎍/㎎ and 12.86±0.86 ㎍/㎎. OJS-F which is LPS has diminished in the LPS-induced release of inflammatory mediators (NO, iNOS, COX2 and PGE2) and pro-inflammatory cytokines (TNF-α, IL-6 and IL-1β) from the RAW264.7 macrophages. Therefore, the developed formulation for tablet of ORS-F provide efficiency and usability, and indicated effect of anti-inflammation.

• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.21-28
• /
• 2015

Recent studies on concrete floating structure development focused on connection system of concrete modules. Precast concrete modules are designed to be attached by prestressing in the water, exposing the structure to the loads from water and making the construction difficult. Therefore, a development of bond material became a key issue in successful connection of floating concrete modules. In this study, micro-silica mixed aqua epoxy (MSAE) is developed for the task. Existing primer aqua epoxy, originally used as a bond material for the retrofit of concrete structures using fiber reinforced polymers, is evaluated to find the optimum micro-silica added mix proportion. Micro-silica of 0~4 volume % was mixed in standard mixture of aqua epoxy. Then, the material property tests were performed to study the effect of micro-silica in aqua epoxy by controlling the epoxy silane proportion by 0, ${\pm}5$, ${\pm}10%$. The optimum mix design of MSAE was derived based on the test results. The MSAE was used to connect concrete module specimens with the epoxy thickness variation of 5, 10, and 20mm. Then, 3-point loading test was performed to verify the bond capacity of MSAE. The results show that MSAE improves the bond capacity of concrete module.