• 대한설비공학회지:설비저널
• /
• 제4권1호
• /
• pp.6-17
• /
• 1975

For a periodic variation of the flue gas temperature the heat conduction through the Ondol floor was analysized. Also the heat loss to the ground was estimated. The floor thermal capacity, as a function of the floor thickness, has strong influence on the time lag of the temperature variation. It is an important design parameter for intermittent heating. Even for the steady periodic variation, there was significant heat loss to the ground below the Ondol floor.

• Coupled systems mechanics
• /
• 제9권4호
• /
• pp.381-396
• /
• 2020

Analytical investigation of the fracture of inhomogeneous beam with two parallel lengthwise cracks is performed. The thickness of the beam varies continuously along the beam length. The beam is loaded in three-point bending. Two beam configurations with different lengths of the cracks are analyzed. The two cracks are located arbitrary along the thickness of the beam. Solutions to the strain energy release rate are derived assuming that the material has non-linear elastic mechanical behavior. Besides, the beam exhibits continuous material inhomogeneity along its thickness. The balance of the energy is analyzed in order to derive the strain energy release rate. Verifications of the solutions are carried-out by considering the complementary strain energy stored in the beam configurations. The influence of the continuous variation of the thickness along the beam length on the lengthwise fracture behavior is investigated. The dependence of the lengthwise fracture on the lengths of the two parallel cracks is also studied.

• Steel and Composite Structures
• /
• 제19권3호
• /
• pp.679-695
• /
• 2015

A numerical solution using finite difference method to evaluate the thermal buckling of simply supported FGM plate with variable thickness is presented in this research. First, the governing differential equation of thermal stability under uniform temperature through the plate thickness is derived. Then, the governing equation has been solved using finite difference method. After validating the presented numerical method with the analytical solution, the finite difference formulation has been extended in order to include variable thickness. The accuracy of the finite difference method for variable thickness plate has been also compared with the literature where a good agreement has been found. Furthermore, a parametric study has been conducted to analyze the effect of material and geometric parameters on the thermal buckling resistance of the FGM plates. It was found that the thickness variation affects isotropic plates a bit more than FGM plates.

• 로봇학회논문지
• /
• 제5권1호
• /
• pp.32-40
• /
• 2010

This paper proposes the technique of estimating the pipe thickness using the measured group velocity. To measure the group velocity from the accelerometer data in the frequency domain, Wigner-Ville distribution is utilized, which interprets the waveform of the shock wave. Using this measured group velocity, this paper proposes the technique to estimate the thickness of pipes with the impact on the pipe. The group velocity is estimated by the modeling correlation between the group velocity and the thickness of the pipe based on the propagation velocities. The correlation model between thickness and group velocity has been proved through the real experiments. The measured group velocity in the frequency-domain is the maximum at the center frequency of the bending waves in the modeling of the group velocity. In addition to these, a smoothing technique for analyzing lamb wave Wigner-Ville distribution has been introduced to improve the reliability of the data acquisition.

• 한국정보통신학회논문지
• /
• 제18권1호
• /
• pp.135-141
• /
• 2014

본 연구에서는 무접합 MuGFET의 핀 폭에 따른 문턱전압의 변화를 줄이기 위한 소자 설계 가이드라인을 제시하였다. 제작된 무접합 MuGFET으로부터 핀 폭이 증가할수록 문턱전압의 변화가 증가하는 것을 알 수 있었다. 무접합 MuGFET의 핀 폭에 따른 문턱전압의 변화를 줄이기 위한 소자 설계가이드라인으로 게이트 유전체, 실리콘박막의 두께, 핀 수를 최적화 하는 연구를 3차원 소자 시뮬레이션을 통해 수행하였다. 고 유전율을 갖는 $La_2O_3$ 유전체를 게이트 절연층으로 사용하거나 실리콘 박막을 최대한 얇게 하므로 핀 폭이 증가해도 문턱전압의 변화율을 줄일 수 있음을 알 수 있었다. 특히 유효 채널 폭을 같게 하면서 핀 수를 많게 하므로 문턱전압 변화율과 문턱전압 아래 기울기를 작게 하는 것이 무접합 MuGFET의 최적의 소자 설계 가이드라인임을 알 수 있었다.

• 제어로봇시스템학회논문지
• /
• 제21권8호
• /
• pp.735-741
• /
• 2015

In this paper, we suggest a dimensional controller to produce a different thickness strip without adding production facilities at the same steel. We describe the model for the non-linear thickness and speed setup, and drive a variation of the speed and thickness with Talyor expansion. The control algorithm is composed of 8 steps and the transient condition is added in order to maintain a mass flow between stands. A simulator is developed in order to verify the algorithm, and includes a non-linear rolling model, the tension model, AGC model, the disturbance model, and so on. From the simulation results by disturbances, we show that the thickness, tension and looper angle are converged to the set condition when we change the rolling conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.642-645
• /
• 2008

A pin fin with variable fin base thickness is analysed by using the one dimensional analytic method. Heat loss and fin thermal resistance are presented as a function of the fin base thickness, pin fin outer radius and convection characteristic numbers ratio. The relationship between the fin outer radius and fin base thickness for the same amount of heat loss is shown. One of the results indicates the fin thermal resistance decreases as the fin outer radius and/or convection characteristic numbers ratio increase whereas the fin thermal resistance is independent on the variation of fin base thickness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.320-320
• /
• 2013

Film thickness monitoring with plasma impedance monitoring (PIM) is demonstrated for small area $SiO_2$ RF plasma etching processes in this work. The chamber conditions were monitored by the impedance signal variation from the I-V monitoring system. Moreover, modified principal component analysis (mPCA) was applied to estimate the $SiO_2$ film thickness. For verification, the PIM was compared with optical emission spectroscopy (OES) signals which are widely used in the semiconductor industry. The results indicated that film thickness can be estimated by 1st principal component (PC) and 2nd PC. Film thickness monitoring of small area $SiO_2$ etching was successfully demonstrated with RF plasma harmonic impedance monitoring and mPCA. We believe that this technique can be potentially applied to plasma etching processes as a sensitive process monitoring tool.

• 한국음향학회지
• /
• 제27권6호
• /
• pp.271-278
• /
• 2008

압전판의 길이나 폭에 따라 두께가 변화하는 압전 세라믹을 사용하여 광대역 특성을 구현하는 초음파 트랜스듀서에 대하여 압전진동자의 측면에서 본 형태에 따른 전기-음향적 특성해석을 이론적으로 수행하였다. 압전진동자의 길이방향에 따른 두께 변화를 지수함수의 조합으로 표현하고 이 함수를 이용하여 압전진동자의 전기단자에서 본 자유 어드미턴스 및 파워전달함수에 대한 식을 도출하였다. 대표적인 PZT압전 세라믹을 예로 들어 압전 진동자의 측면 형태변화에 따른 비 대역폭을 고찰해본 결과 넓은 대역폭를 얻기 위한 최적의 형태가 존재함을 알 수 있었으며, 압전진동자의 최대두께에 대한 최소두께 비가 자아짐에 따라 대역폭은 100%이상까지도 넓어질 수 있으나 파워전달함수는 반대로 감소하는 경향을 확인할 수 있었다. 또 압전진동자의 길이가 길어질수록 전달함수의 크기는 증가하나 광대역 특성을 갖는 압전진동자의 형태는 매우 한정적이 됨을 확인할 수 있었으며 이는 고효율의 광대역 초음파 트렌스듀서 제작에 있어서는 정밀한 가공이 요구됨을 확인할 수 있었다.

• 대한통합의학회지
• /
• 제11권1호
• /
• pp.149-157
• /
• 2023

Purpose : Genu varum is a condition characterized by a wider than normal gap between. This may be due to muscle weakness caused by poor posture, lifestyle, or lack of exercise. This study aimed to compare the effects of ball-based squats and narrow squats on muscle thickness, Q-angle, and the gap between the knees, in order to assess the potential for improving this condition. Methods : Twenty six adult participants with genu varum were randomly assigned to either a ball-based squat group (n=13) or a narrow squats group (n=13). Both groups performed their respective exercises three times weekly for 4 weeks. The data was analyzed using paired t-tests to compare pre- and post- intervention measurements within each group, and independent t-test was used to compare the two groups. Results : Both groups showed significant improvement in the thickness of the vastus lateralis and medialis, and rectus femoris muscles, as well as a significant decrease in the gap between the knees (p<.05). However, there was no significant difference in Q-angle variation between the two group. Furthermore, there was no significant differences in the Q-angle, gap between the knees, and muscle thickness variation between both groups. Conclusion : The results suggest that both ball-based squats and narrow squats are effective in improving muscle thickness and reducing the gap between the knees in adults with genu varum. However, there was no significant difference between the two types of squats in terms of their effects on the Q-angle. These findings highlight the potential for exercise interventions to address this common postural issue.