• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1996.11a
• /
• pp.131-139
• /
• 1996

To quantitatively investigate the effects of manure compost on the soil and water environment including ground water the elution patterns of anions and hydraulic conductivity wore estimated with four different depth(15, 30, 45 60cm) and four variable ratio of compost treatment(0, 2, 4, 6%) through soil column test. 1. There were over 95% of elution of chloride and nitrate within 0.1 pore volume(PV), and sulfate within 0.2 PV. With 2 ton/10a of cow manure compost treatment recommended total 40 kg/10a of anions added was recovered as effluent at the amount of 17kg chloride, 5.4kg nitrate, and 13.2kg sulfate, respectively However, phosphate rarely recovered in the effluent due to the strong affinity for sorption sites in soils. 2. In multi-layered soil column the maximum peaks of each anion eluted were retardated with increasing soil depth and the amount of organic matter(OM) treatment. 3. With increasing OM up to 2% the saturated hydraulic conductivity(SHC) was greatly decreased, but the slight decrease in SHC was found by addition of OM greater than 4％. In multi-layered soil column SHC was more effected by the lower SHV layer than by that of the higher.

• Geotechnical Engineering
• /
• v.5 no.4
• /
• pp.5-16
• /
• 1989

This paper statistically analyses the freezing soil by frost group and frost depth in Korea with data from soil testing in the Korea National Housing Corporation, the climate data provided by the Central Weather Office and the data on the frost depth from the National Construction Laboratory Institute. In this paper, freezing variable are analysed such as percentage finer than 0.02 m by weight, plasticity index, freezing index, water contents of soil and frost depth etc‥‥ The result of the analysis is as follows. 1) The frost depth of Korea depends on the properties of soil rather thank the characte fistic of area. 2) The distribution map of design freezing index in 57 cities is drawn up with the maxi- mum freezing index, during past 14 years, calculated by the average of the air temperature observed four times(03 : 00.09 00, 15 : 00, 21 : 00) a day. 3) By correcting the OLS line estimated from the relationship between freezing index and frost depth, a method of utlizing the line with the upper confidence limit of 99.9% int-distribution as predicted maximum frost depth is newly introduced.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.427-427
• /
• 2015

The storm water management and drainage relation are the key variable that plays a vital role on hydrological design and risk analysis. These require knowledge about spatial variability over a specified area. Generally, design rainfall values are expressed from the fixed point rainfall, which is depth at a specific location. Concurrently, determine the areal rainfall amount is also very important. Therefore, a spatial rainfall interpolation (point rainfall converting to areal rainfall) can be solved by areal reduction factor (ARF) estimation. In mainland of South Korea, for dam design and its operation, public safety, other surface water projects concerned about ARF for extreme hydrological events. In spite of the long term average rainfall (2,061 mm) and increasing extreme rainfall events, ARF estimation is also essential for Jeju Island's water control structures. To meet up this purpose, five fixed rainfall stations of automatic weather stations (AWS) near the "Hancheon Stream Watershed" area has been considered and more than 50 years of high quality rainfall data have been analyzed for estimating design rainfall. The relationship approach for the 24 hour design storm is assessed based on ARF. Furthermore, this presentation will provide an outline of ARF standards that can be used to assist the decision makers and water resources engineers for other streams of Jeju Island.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.57-62
• /
• 2018

In this report, Cutting of metals are basically existence of fundamentally important cutting method. It is necessary task for the advanced technical production which are need more precision and efficient to over an idealistic surface roughness. This study is resulted through cutting the row materials of SM45C, in the diluted solubility water type of cutting fluids twenty times and forty times as many as that water, by variable in the velocity, feed rate, depth of cut, comparing the examine under same cutting conditions.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.2
• /
• pp.76-83
• /
• 1993

In this study, an approximate method for calculating the directional spectrum of waves encountering a current in shallow water is developed. The wave trains in tile directional spectrum are assumed to be linear and Gaussian; development of the spectrum requires that the waves also be short crested. The Miche's breaking criterion is imposed to determine the upper limit of wave height and to establish an expression for the breaking wave elevation in terms of the ideal wave's elevation and the second time derivative of wave elevation. Two examples are given; one for a Wallops directional spectrum encountering a shear current and another with an upwelling current.

• Water for future
• /
• v.17 no.2
• /
• pp.113-124
• /
• 1984

The equations for the wave orthogonals and wave heights are presented along the depth using time as the independent variable, The effect of wave refracion is included. In this paper, a numerical procedure is described for the calculation and two analytical solutions are presneted in case of straight and parallel bottom contours and horizontal bottom in order to check the computed results. The computer outputs are in the form of automatically plotted wave orthogonals and wave heights along the wave path. In practical calculation of wave heights, Samchuckk Pohang, and Hanlim are selected as plane sloping bottoms.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.6
• /
• pp.59-66
• /
• 2012

The purpose of this study is to estimate the behavior and the mechanism of debris flow on the slope, which has specially various gradient plane. The numerical simulation was performed by using the Finite Differential Element method (FDM) based on the equation for the mass conservation and momentum conservation. The mechanism of flow type for debris flow is divided into three flow types which are stony debris flow, immature debris flow, and turbulent water flow, respectively. First, flow discharge, water flow depth, sediment volume concentration was investigated by variable input of flow discharge at the straight slope angle and two step inclined plane. As the input of flow discharge was decrease, flow discharge and water flow depth was increased, after the first coming debris flow only reached at the downstream. As the input of flow discharge was increased, the curve of flow discharge and flow depth was highly fluctuated. As the results of RMS ratio, the flow discharge and flow depth was lower two step slope angle than the straight slope angle. Second, the behavior of debris flow was investigated by the four cases of gradient degree at the downstream of slope angle. The band width of flow discharge and flow depth for $14^{\circ}$ between $16^{\circ}$ was higher than other gradient degree, and fluctuation curve was continuously high after 10 seconds.

• Journal of Korean Society on Water Environment
• /
• v.28 no.1
• /
• pp.137-147
• /
• 2012

Land surface temperature in ecohydrology is a variable that links surface structure to soil processes and yet its spatial prediction across landscapes with variable surface structure is poorly understood. And there are an insufficient number of soil temperature monitoring stations. In this study, a grid-based land surface temperature prediction model is proposed. Target sites are Andong and Namgang dam region. The proposed model is run in the following way. At first, geo-referenced site specific air temperatures are estimated using a kriging technique from data collected from 60 point weather stations. Then surface soil temperature is computed from the estimated geo-referenced site-specific air temperature and normalized difference vegetation index. After the model is calibrated with data collected from observed remote-sensed soil temperature, a soil temperature map is prepared based on the predictions of the model for each geo-referenced site. The daily and monthly simulated soil temperature shows that the proposed model is useful for reproducing observed soil temperature. Soil temperatures at 30 and 50 cm of soil depth are also well simulated.

• Corrosion Science and Technology
• /
• v.6 no.3
• /
• pp.103-111
• /
• 2007

The effect of stress factors on the growing process of stress corrosion cracking (SCC) of the sensitized 18-8 stainless steel in high temperature water was investigated using equations of crack growth rate derived from applying electric circuits to SCC corrosion paths. Three kinds of cross sections have to be considered when electric circuit is constructed using total current. The first is ion flow passage area, $S_{sol}$, of solution in crack, the second is total dissolving surface area, $S_{dis}$, of metal on electrode of crack tip and the third is dissolving cross section, $S_{met}$, of metal on grain boundary or in base metal or in welding metal. Stress may affect each area. $S_{sol}$ may depend on applied stress, $\sigma_{\infty}$, related with crack depth. $S_{dis}$ is expressed using a factor of $\varepsilon(K)$ and may depend on stress intensity factor, K only. SCC crack growth rate is ordinarily estimated using a variable of K only as stress factor. However it may be expected that SCC crack growth rate depends on both applied stress $\sigma_{\infty}$ and K or both crack depth and K from this consideration.$\varepsilon(K)$ is expressed as ${\varepsilon}(K)=h_2{\cdot}K^2+h_3{\cdot}K^3$ when $h_{2}$ and $h_{3}$ are coefficients. Also, relationships between SCC crack growth rate, da/dt and K were simulated and compared with the literature data of JBWR-VIP-04, NRC NUREG-0313 Rev.2 and SKIFS Draft. It was pointed out in CT test that the difference of distance between a point of application of force and the end of starter notch (starting point of fatigue crack) may be important to estimate SCC crack growth rate. An anode dissolution current density was quantitatively evaluated using a derived equation.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.63-63
• /
• 2021

Bed shear stress is important variable in river flow analysis. The bed shear stress has an effects on bed erosion, sediment transport, and mean flow characteristics. Quadratic formula to estimate bed shear stress is widely used, 𝜏=𝜌c_fu|u| in which friction coefficient, c_f, needs to be assigned to numerical models. The aim of this study is to estimate Chezy coefficient using bathymetry data measured by ADCP. Bed form geometry variables will be estimated form bed profile, then Chezy coefficient will be determined using estimated bed form geometry variables in order to set friction coefficient to numerical model. From the probability density function obtained from the bathymetry data, Chezy coefficient will be randomly generated since Chezy coefficient is not uniform over the space and it does not depend on spatial variables such as water depth and distance from river bank. Numerical test will be performed to find to demonstrate randomly extracted Chezy coefficient is appropriate. The result of this study is valuable in that the friction coefficient is estimated in consideration of the bed profile, and as a result, uncertainty of the friction coefficient can be reduced.