• Smart Structures and Systems
• /
• v.18 no.5
• /
• pp.955-982
• /
• 2016

Recent studies integrating vibration control and structural health monitoring (SHM) use control devices and control algorithms to enable system identification and damage detection. In this study real-time SHM is used to enhance structural vibration control and reduce damage. A newly proposed control algorithm, including integrated real-time SHM and semi-active control strategy, is presented to mitigate both damage and seismic response of the main structure under strong seismic ground motion. The semi-active independently variable stiffness (SAIVS) device is used as semi-active control device in this investigation. The proper stiffness of SAIVS device is obtained using a new developed semi-active control algorithm based on real-time damage tracking of structure by damage detection algorithm based on identified system Markov parameters (DDA/ISMP) method. A three bay five story steel braced frame structure, which is equipped with one SAIVS device at each story, is employed to illustrate the efficiency of the proposed algorithm. The obtained results show that the proposed control algorithm could significantly decrease damage in most parts of the structure. Also, the dynamic response of the structure is effectively reduced by using the proposed control algorithm during four strong earthquakes. In comparison to passive on and off cases, the results demonstrate that the performance of the proposed control algorithm in decreasing both damage and dynamic responses of structure is significantly enhanced than the passive cases. Furthermore, from the energy consumption point of view the maximum and the cumulative control force in the proposed control algorithm is less than the passive-on case, considerably.

• Geomechanics and Engineering
• /
• v.22 no.4
• /
• pp.361-374
• /
• 2020

This paper is concerned with the thermoelastic bending of FG beams resting on two-layer elastic foundations. One of these layers is Winkler springs with a variable modulus while the other is considered as a shear layer with a constant modulus. The beams are considered simply supported and subjected to thermo-mechanical loading. Temperature-dependent material properties are considered for the FG beams, which are assumed to be graded continuously across the panel thickness. The used theories contain undetermined integral terms which lead to a reduction of unknowns functions. Several micromechanical models are used to estimate the effective two-phase FG material properties as a function of the particles' volume fraction considering thermal effects. Analytical solutions for the thermo-mechanical bending analysis are obtained based on Navier's method that satisfies the boundary conditions. Finally, the numerical results are provided to reveal the effect of explicit micromechanical models, geometric parameters, temperature distribution and elastic foundation parameters on the thermoelastic response of FG beams.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.12
• /
• pp.502-508
• /
• 2016

An optimized PI controller design method is presented to promote the control performance of an oil cooler system for high precision machine tools. First, a transfer function model of the oil cooler system with a variable rotating speed compressor was obtained by the perturbation method as the first order system with a negligible dead time. Then, the closed-loop control system was described as the second order system with a zero. Its dynamic behaviors are mostly governed by characteristic parameters, the damping ratio, and the natural frequency which is incorporated in PI gains. Next, an optimum integral of the time-weighted absolute error (ITAE) criterion was applied to the second order system. The characteristic parameters can be determined by the given design specifications, percent overshoots and settling times and comparisons with the ITAE criterion. Hence, the PI gains were plainly identified in a deterministic way. Finally, the PI gains were fine-tuned to obtain desirable dynamics in real systems, considering the zero effect and parameter variations. The validity of the proposed method was proven by computer simulations and real experiments for selected cases.

• Journal of Powder Materials
• /
• v.29 no.6
• /
• pp.459-467
• /
• 2022

Soft magnetic powder materials are used throughout industries such as motors and power converters. When manufacturing Fe-based soft magnetic composites, the size and shape of the soft magnetic powder and the microstructure in the powder are closely related to the magnetic properties. In this study, Fe-Si-Al-P alloy powders were manufactured using various manufacturing process parameter sets, and the process parameters of the vacuum induction melt gas atomization process were set as melt temperature, atomization gas pressure, and gas flow rate. Process variable data that records are converted into 6 types of data for each powder recovery section. Process variable data that recorded minute changes were converted into 6 types of data and used as input variables. As output variables, a total of 6 types were designated by measuring the particle size, flowability, apparent density, and sphericity of the manufactured powders according to the process variable conditions. The sensitivity of the input and output variables was analyzed through the Pearson correlation coefficient, and a total of 6 powder characteristics were analyzed by artificial neural network model. The prediction results were compared with the results through linear regression analysis and response surface methodology, respectively.

• Structural Engineering and Mechanics
• /
• v.90 no.1
• /
• pp.83-96
• /
• 2024

This paper suggests an analytical approach to investigate the free vibration and stability of functionally graded (FG) beams with both perfect and imperfect characteristics using a quasi-3D higher-order shear deformation theory (HSDT) with stretching effect. The study specifically focuses on FG beams resting on variable elastic foundations. In contrast to other shear deformation theories, this particular theory employs only four unknown functions instead of five. Moreover, this theory satisfies the boundary conditions of zero tension on the beam surfaces and facilitates hyperbolic distributions of transverse shear stresses without the necessity of shear correction factors. The elastic medium in consideration assumes the presence of two parameters, specifically Winkler-Pasternak foundations. The Winkler parameter exhibits variable variations in the longitudinal direction, including linear, parabolic, sinusoidal, cosine, exponential, and uniform, while the Pasternak parameter remains constant. The effective material characteristics of the functionally graded (FG) beam are assumed to follow a straightforward power-law distribution along the thickness direction. Additionally, the investigation of porosity includes the consideration of four different types of porosity distribution patterns, allowing for a comprehensive examination of its influence on the behavior of the beam. Using the virtual work principle, equations of motion are derived and solved analytically using Navier's method for simply supported FG beams. The accuracy is verified through comparisons with literature results. Parametric studies explore the impact of different parameters on free vibration and buckling behavior, demonstrating the theory's correctness and simplicity.

• Structural Engineering and Mechanics
• /
• v.58 no.3
• /
• pp.443-458
• /
• 2016

In this paper, we propose a method for taking into account uncertainties based on the projection on polynomial chaos. Due to the manufacturing and assembly errors, uncertainties in material and geometric properties, the system parameters including assembly defect, damping coefficients, bending stiffness and traction-compression stiffness are uncertain. The proposed method is used to determine the dynamic response of a one-stage spur gear system with uncertainty associated to gear system parameters. An analysis of the effect of these parameters on the one stage gear system dynamic behavior is then treated. The simulation results are obtained by the polynomial chaos method for dynamic analysis under uncertainty. The proposed method is an efficient probabilistic tool for uncertainty propagation. The polynomial chaos results are compared with Monte Carlo simulations.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.519-520
• /
• 2016

BLSRM is a nonlinear, strong coupling and multi-variable system. The conventional control method is vulnerable to uncertain factors such as the load disturbance and satellite parameters change. It is difficult to obtain satisfactory control effect. Basing on a 8/10 BLSRM, whose suspending force control is separated with the torque control, this paper presents adaptive fuzzy PID controller for levitation control, which apply the fuzzy logic control to the conventional PID controller for parameters self-tuning. Both fuzzy and parameters of PID controller are self-tuning on-line, which improve the performance of controller. Finally, simulation and experimental results show the performance of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.247-249
• /
• 1996

The indirect vector control method is generally used for variable speed control of induction motor, due to its excellent response characteristics. However, this is very sensitive to the variation of motor parameters caused by temperature rise and magnetic saturation and so on. Linear induction motor(LIM) has asymetric phase circuit parameters because of its special phenomena, end effects. So this paper describes on the method that identifies the circuit parameters using neural network in the vector control of LIM.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.53-55
• /
• 2007

Industrial interest in switched reluctance moor (SRM) drives has varied since 1850s. This has been primarily due to the emerging markets for variable speed drives in consumer and industrial products, such as home appliances, air conditioning, hand tools, fans, pump motor, etc. However, SRM has been plagued with the acoustic noise and vibration problem by input power of fixed section. Therefore, This paper offers electromagnetic analysis for torque ripple reduction in mechanical geometry and electric parameters. This means that the rotor pole arc and electric parameters have related to produce the active and negative torque. This analysis results are verified by the finite element method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.43-49
• /
• 2001

When designing a gerotor, designers determine basic dimensions of a gerotor with transmitted power considering strength, interference and so. on. But, designers can not easily obtain the tooth profile generated by dimensions as well as the geometry bob for cutting the tooth profile. In order to resolve these problems, an automatic design sys-tem creating not only the solid model of a gerotor but also that of the generating hob using the design parameters of dimen-sions is developed. Through the developed system, designers can improve the efficiency of design and satisfy the variable requirements of design as well. In this research, the three-dimensional solid models for gerotors are generated considering the design parameters. Besides, those for generating hob regarding the design parameters of hob is created automatically.