• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.1176-1189
• /
• 2016

In this paper, a novel quasi-direct power control (Q-DPC) scheme based on a resonant frequency adaptive proportional-resonant (PR) current controller with a variable frequency resonant phase locked loop (RPLL) is proposed, which can achieve a fast power response with a unity power factor. It can also adapt to variations of the generator frequency in T-type Three-level shaft synchronous generator (SSG) converters. The PR controller under the static α-β frame is designed to track ac signals and to avert the strong cross coupling under the rotating d-q frame. The fundamental frequency can be precisely acquired by a RPLL from the generator terminal voltage which is distorted by harmonics. Thus, the resonant frequency of the PR controller can be confirmed exactly with optimized performance. Based on an instantaneous power balance, the load power feed-forward is added to the power command to improve the anti-disturbance performance of the dc-link. Simulations based on MATLAB/Simulink and experimental results obtained from a 75kW prototype validate the correctness and effectiveness of the proposed control scheme.

• 한국전자파학회논문지
• /
• 제24권6호
• /
• pp.602-612
• /
• 2013

본 논문에서는 주파수 5.3 GHz에서 소형화된 branch line 커플러와 $360^{\circ}$ 이상의 위상천이를 보일 수 있는 가변 리액턴스 부하를 결합하여 소형화된 위상천이기의 설계를 보였다. 위상천이기의 소형화를 위하여, branch line 커플러의 새로운 구조를 제안하였다. 새로운 branch line 커플러는 전송선의 T 및 ${\pi}$형 등가회로 변환 방법을 이용하여 소형화하였다. 소형화된 branch line 커플러는 일반적인 구조에 비해 50 % 이상 소형의 크기를 가진다. 넓은 위상천이량을 갖기 위하여 전송선에 버렉터 다이오드 두 개를 입력과 출력에 연결한 부하 구조를 채택하였다. 특히, 조정 전압에 대한 위상천이량이 완만하도록 임피던스 변환기 역할을 하는 전송선을 설계된 부하 구조에 추가하여 구조를 보완하였다. 추가된 임피던스 변환기에 사용된 전송선 및 선정된 부하 구조의 전송선은 소형화에 장애가 되기 때문에 이를 집중 소자로 등가하여 소형화하였다. 제작된 위상천이기는 $15{\times}15mm^2$의 소형의 크기를 가지며, 조정 전압 0~10 V 범위의 경우, 중심 주파수 5.3 GHz에서 삽입 손실은 약 -4~-6 dB, 반사 손실은 -20 dB 이하, 약 $480^{\circ}$의 넓은 위상천이를 보였다.

• Structural Engineering and Mechanics
• /
• 제18권4호
• /
• pp.389-410
• /
• 2004

In this study, theoretical and experimental results are presented which were obtained during an investigation of the influence of the $P-{\Delta}$ effect that was caused by the simultaneous changing of the axial load P of the column and the lateral displacement ${\Delta}$ in the external beam-column joints. The increase or decrease of ${\Delta}$ was simultaneous with the increase or decrease of the axial compression load P and caused an additional influence on the aseismic mechanical properties of the joint. A total of 12 reinforced concrete exterior beam-column subassemblies were examined. A new model, which predicts the beam-column joint ultimate shear strength, was used in order to predict the seismic behaviour of beam-column joints subjected to earthquake-type loading plus variable axial load and $P-{\Delta}$ effect. Test data and analytical research demonstrated that axial load changes and $P-{\Delta}$ effect during an earthquake cause significant deterioration in the earthquake-resistance of these structural elements. It was demonstrated that inclined bars in the joint region were effective for reducing the unfavourable impact of the $P-{\Delta}$ effect and axial load changes in these structural elements.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2010년도 춘계 학술논문 발표대회 1부
• /
• pp.67-70
• /
• 2010

This study investigates the physical properties of the acrylic emulsion mortar according to variable composition set of redispersible emulsion powders. This materials have to be composed of many types of binders and chemical additives. So it is difficult to decide suitable mixing proportion of composition materials. The redispersible emulsion powders using "2, 4, 6, 8kg" of EVA polymers dispersion ranges are prepared with acrylic emulsion mortars and were tested for basic characteristics such as flexural, and compressive strength, wheel load. Through experiments we found that the improved formula to satisfy the standard of wheel load by EVA polymers, and the masration rangs between about 2.0% to 2.6% which the white portland cenmet and EVA polymers is good for resistauce wheel load.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권3호
• /
• pp.317-322
• /
• 2011

This work has investigated the exhaust emissions such as Total Hydrocarbon (THC), Nitrogen Oxides(NOx), and Particulate Matter (PM) characteristics emitted from the tail-pipe of a continuously variable valve timing (CVVT) gasoline-fueled engine with different intake valve opening timings and injection pressures at the part load condition. Valve overlap period was varied from $40^{\circ}CA$ to $10^{\circ}CA$ and fuel injection pressure was increased from 3.5 bar to 5.0 bar. THC and NOx emissions decreased as intake valve opening timing was advanced regardless of fuel injection pressure. When the fuel was injected with the condition of 5.0 bar at all of valve overlap ranges, THC levels were reduced by 55%. NOx concentrations were diminished about 75% as valve overlap increased. PM size distributions were analyzed as bi-modal type of the nucleation and accumulation mode. Comparing with fuel injection pressures, PM emission levels were decreased at high pressure injection of 5.0 bar condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1075-1080
• /
• 2007

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1217-1220
• /
• 1996

For the purpose of the good tracking to variable load demands of the thermal power plant, a decentralized multilevel control(DMC) scheme is presented. It is applied to the drum type boiler-turbine system which is simplified from Boryung T/P #1,2 model[4]. A linearized model is decomposed into three subsystems by means of linear transformation. Then the DMC based on such subsystem is designed. Simulation using Matlab-Simulink shows that the proposed algorithm works very well to the large step change of power demand.

• 전기의세계
• /
• 제17권1호
• /
• pp.6-10
• /
• 1968

To control of the speed of induction Motor, a variable frequency power supply is needed. But this New type induction Motor Constitute stator and Rotor with New principle, its speed can be easily and widely Controlled by changing phase of the stator, and start at low current than rating without starter. Also, its no load current is same as shart current, and speed increase in proportion to current. On this points this induction Motor for speed control is different from induction Motor using Now.

• 한국항해항만학회지
• /
• 제36권10호
• /
• pp.839-844
• /
• 2012

풍향풍속계는 실시간으로 풍향과 풍속을 측정하는 기상관측기구로서 바람의 영향을 많이 받는 항만, 조선소, 해상구조물, 또는 건설현장에서 사용되는 크레인에 장착되어 작업가능 여부를 알리거나 전도 사고를 예방하기 위한 안전시스템과 연동되어 사용된다. 로드 셀형 풍향풍속계는 4개의 수풍부에 연결된 로드 셀의 하중 합을 이용하여 풍속을, 하중 비를 이용하여 풍향을 측정한다. 선행연구에 따르면, 풍향에 따른 인접한 두 수풍부의 하중 비는 날개 주위에 와류로 인해 불규칙한 값을 보이게 되며, 이는 풍향 오차를 증가시키는 원인이 된다. 본 연구에서는 이러한 오차를 줄이기 위하여 세 가지 수풍부 형상에 따른 하중 비를 분석하고, 오차를 줄일 수 있는 수풍부 형상을 제시하고자 한다. 수풍부 형상에 따른 하중 비를 비교하기 위해 ANSYS CFX를 사용하여 유동해석을 수행하였으며, 설계변수로 0도에서 90도까지 11.25도 간격으로 9가지 풍향조건을 설정하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권1호
• /
• pp.9-15
• /
• 2003

This Paper deals with the design of Moving Magnet type Linear Oscillatory Actuator(MM-LOA) using spring damper based on the design procedure and the characteristic analysis. MM-LOA is applied to variable load such as vaccum pump and compressor, The structure of piston type is selected to reduce a noise. MM-LOA has over-displacement in starting state because of the low inertia of mover To improve the starting characteristic, spring damper is used. The optimum spring constant of spring damper is detected and in consideration of spring damper, MM-LOA redesigned. The parameter is calculated by Finite Element Method(FEM). For the dynamic characteristic analysis, time differential method composed of voltage and kinetic equation is used. The propriety of the improved model is verified through the experimental results.