• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.2
• /
• pp.68-74
• /
• 2001

A design and implementation method for the UHF-band(800MHz) variable attenuator using the 3dB coupler is proposed. The 90 degree, 3-dB Coupler is used for the variable attenuator. The principal theory for the 3-dB coupler is introduced. The 3-dB Coupler is designed by the mathematical analysis and a computer simulation tool. A PIN diode is used for the variable resistor at UHF-band. The variable attenuator using the 3-dB coupler and the PIN diode is designed and implemented. The measured results for the variable attenuator by a network analyzer show that the insertion loss is below -l0dB, and the continuous variable attenuation range is about 10dB.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.206-209
• /
• 2016

This letter proposes a reconfigurable directional coupler that uses a variable impedance mismatch reflector to achieve high isolation characteristics in the antenna front end. The reconfigurable coupler consists of a directional coupler and a single-pole four-throw (SP4T) switch with different load impedances as a variable load mismatch reflector. Selection of the load impedance by the reflector allows cancellation of the reflected signal due to antenna load mismatch and the leakage from the input to isolation port of the directional coupler, resulting in high isolation characteristics. The performance of the proposed architecture in separating the received (Rx) signal from the transmitted (Tx) signal in the antenna front end was verified by implementing and testing the reconfigurable coupler at 917 MHz for UHF radio-frequency identification (RFID) applications. The proposed reconfigurable directional coupler showed an improvement in the isolation characteristics of more than 20 dB at the operation frequency band.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.147-152
• /
• 2008

This paper has been fabricated the two different type of variable attenuators using a characteristics of a 3 dB directional coupler and pin diodes. One was not analyzed using the conventional even-odd modes but used simple two-port techniques. The resulting scattering parameters described operation characteristics for the general case where the terminating impedances are equal and unequal. After analyzing resistor role of the ${\pi}$ type fixed attenuator. this paper used a pin diode instead of a resistor. The variable attenuators were fabricated using pin diodes for current-controlled attenuation on the coupled ports of a 3 dB branch-line coupler and ${\pi}$ type fixed attenuator. The realized variable attenuators have more than 33 dB attenuation ranges at 2.1 GHz. and the input and output reflection coefficients are less than -13 dB. These results could be applied to mobile communication systems. It can be varied gain of the power amplifier according to change a outdoor environmental temperature and improved linearity.

• Korean Journal of Optics and Photonics
• /
• v.26 no.1
• /
• pp.38-43
• /
• 2015

We propose a linearly polarized long-cavity Yb:YAG laser with a variable-reflectivity output coupler and investigate its output characteristics. The variable output coupler consists of a polarized beam splitter and a quarter-wave plate. The linearly polarized laser has a long cavity length of about 3.7 m. The slope efficiency of the proposed laser is 19%, and the beam quality ($M^2$) is about 1.2.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.245-251
• /
• 2017

The proposed variable pawer divider in this paper is composed of one equal power 2-way Wilkinson power divider, two variable phase shifters with 90-degree phase variation to be connected two output paths of the 2-way power divider, and one branchline coupler to combine output signals of two variable phase shifter. The proposed variable power divider can theoretically have an arbitrary power division ratio ranging from ${\infty}:1$ to ${\infty}:1$ due to 90-degrees phase variation of two phase shifter. The proposed power divider circuit fabricates on laminated TLX-9(h=20 mil, er=2.5; Taconic) with a center frequency of 1.7 GHz. The power division ratio of the fabricated prototype varies from about 1:100 to 200:1, with an input reflection characteristic(S11) of below -16 dB, an insertion loss of about -1.0 dB, and an isolation characteristic of below -17 dB between two output ports in the range 1.65-1.75 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.253-259
• /
• 2016

This paper introduces a new variable power divider circuit with an arbitrary power division ratio ranging from $1:{\infty}$ to ${\infty}:1$. The proposed power divider circuit consists of one branch-line coupler to be a good input matching characteristic, two variable phase shifters with 90-degree phase variation to be connected two output paths of the branch-line coupler, and one ring-hybrid coupler to combine output signals of two variable phase shifter. The power division ratio between the two output ports of the proposed power divider can be easily controlled by the phase variation of the two phase shifter. The proposed power divider circuit fabricates on laminated RF-35 (h = 20 mil, er=3.5; Taconic) with a center frequency of 2 GHz. The power division ratio of the fabricated prototype varies from about 1:1000 to 5000000:1, with an input reflection characteristic(S11) of below -20 dB, an insertion loss of about -1.0 dB, and an isolation characteristic of below -17 dB between two output ports in the range 1.9-2.1 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.602-612
• /
• 2013

In this paper, a design and fabrication of miniaturized 5.3 GHz reflection type $360^{\circ}$ analog phase shifter with branch line coupler and $360^{\circ}$ variable reactance load. In order to miniaturize phase shifter, novel branch line coupler is proposed. The novel branch line coupler is miniaturized using transformation of transmission line to T and ${\pi}$ type equivalent circuit. The miniaturized branch line coupler has small size of above 50 % compared with conventional branch line coupler. For wide phase shift range, $360^{\circ}$ variable reactance load structure is adopted. Especially, the structure was improved for linear phase shift by adding transmission line which acts as an impedance transformer. The improved structure was miniaturized using the equivalent lumped-element of transmission line. The fabricated phase shifter with $15{\times}15mm^2$ shows wide phase shift of above $480^{\circ}$, the insertion loss of -4~-6 dB and the reflection loss of below -20 dB at 5.3 GHz under 0~10 V control voltage range.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.41-46
• /
• 2018

Recently, the importance of the northeast economies including Russia has been growing, and according to the Eurasian initiative policy, the enhancement of transportation, logistics and connectivity between the northeast Asian countries is emerging as one of the challenges for future growth. However, due to the different vehicle systems used in each country, the railway connections between countries are not operating smoothly. Especially, the couplers of the railway cars which pass through the countries of northeast Asia including Russia have different regulations, which render their shape and characteristics incompatible. In this study, we propose a method of interconnecting the AAR type coupler used in Korea and China and the CA-3 type coupler compatible with the Russian GOST standard, and verify that its structural safety conforms with each set of regulations. We analyze the possibilities offered by this method of interconnection by performing tests while developing materials satisfying the mechanical properties required for the freight coupler.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.351-352
• /
• 2007

• Journal of the Optical Society of Korea
• /
• v.10 no.4
• /
• pp.169-173
• /
• 2006

This paper describes an efficient optimal design method for an arrayed waveguide grating (AWG) having MMI coupler with flattened transfer function. The objective function is the norm of the difference between calculated and target spectra. To analyze the AWG transfer function, the Fresnel-Kirchhof diffraction formula was employed and the design variable was optical path difference of each array waveguide. The (1+1) Evolution Strategy was applied to an eight-channel coarse wavelength division multiplexing (CWDM) AWG as the optimization tool. For obtaining a broadened spectrum, we use a MMI coupler and the variation in optical path difference at each array waveguide changes the shape of the transfer function to obtain the optimal spectrum shape.