• Journal of the Korean Ceramic Society
• /
• v.28 no.10
• /
• pp.777-784
• /
• 1991

Diamond films have been growth by the hot-filament chemical vapor deposition (HFCVD) using CH4 and H2 gaseous mixture on the Si substrate. The experimental results indicated that the deposits were pure diamond and contained no amount of non-diamond phases such as amorphous carbon or graphite. The diamond films were deposited well at the conditions: the filament temperature of 210$0^{\circ}C$, the substrate temperature of 77$0^{\circ}C$, the CH4 concentration of 1.76%, the reactor pressure of 30 torr, and the deposition time of 7 hr. At this growth condition, the maximum deposition rate was 2 ${\mu}{\textrm}{m}$/hr. X-ray diffraction patterns and texture coefficient results showed that preferred orientation of the diamond films was {111} orientation under all experimental conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.5
• /
• pp.563-572
• /
• 1998

An experimental study of hot filament chemical vapor deposition(HFCVD) has been carried out for the fabrication of diamond thin film. Of particular interest is the measurement of deposition uniformity on large substrates. Experimental apparatus including a vacuum chamber, heating elements, etc. has been designed and manufactured. Deposition profiles for different pretreatment powders and different flow rates have been measured in conjunction with the measurement of substrate temperature distribution on a large substrate surface. As the flow rate increases, deposition rate increases, however, the crystallinity becomes worse. Higher growth rate has been found on the region closer to the center location where substrate temperature is higher. The crystallinity has been improved as gas flow rate decreases. The growth rate and morphology of deposition were identified by SEM and the existence of diamond phase was proved by Raman spectroscopy.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.122-122
• /
• 2003

In recent years, there has been increasing interest in quasi one-dimensional nanostructural systems, because of their numerous potential applications in various areas, such as materials sciences, electronics, optics, magnetism and energy storage. Specifically, zinc oxide (ZnO) is recognized as one of the most promising oxide semiconductor materials, because of its good optical, electrical, and piezoelectrical properties. The ZnO nanorods were synthesized using vapor-solid (VS) mechanism on soda lime glass substrate without the presence of metal catalyst. ZnO nanorods were prepared thermal evaporation of a Zn powder at 500. As-fabricated ZnO nanorods had an average diameter and length of 40nm and 3$\mu\textrm{m}$. Transmission electron microscopy revealed that the ZnO nanorods were single crystalline with the growth direction perpendicular to the (101) lattice plane. The influences of reaction time on the formation of the ZnO nanorods were investigated. The Photoluminescence measurements showed that the ZnO nanorods had a strong ultraviolet emission at around 380nm and a green emission at around 500nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.935-938
• /
• 2001

Carbon nanotubes(CNTs) was successfully grown on Ni coated silicon wafer substrate by applying PECVD technique(Plasma Enhanced Chemical Vapor Deposition). As a catalyst, Ni thin film of thickness ranging from 15∼30nm was prepared by electron beam evaporator method. In order to find the optimum growth condition, the type of the gas mixture such as C$_2$H$_2$-NH$_3$was systematically investigated by adjusting the gas mixing ratio in temperature of 600$^{\circ}C$ under the pressure of 0.4 torr. The diameter of the grown CNTs was 40∼150nm. As NH$_3$etching time increased the diameters of the nanotubes decreased whereas the density of nanotubes increased. TEM images clearly demonstrated synthesized nanotubes was multiwalled. We investigated electrical properties for the application of FED.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.71-73
• /
• 1995

In this work, we synthsized GaN powders by the direct reactions of Ga with NH$_3$at the temperature range of 950∼1150$^{\circ}C$ and we growth the GaN thin films on Si and sapphire substrates using the synthesized GaN powders by the vapor phase epitaxy method. The synthesized powder had hexagonal crystal structures with lattice constants of a$\sub$0/=3.1895${\AA}$, c$\sub$0/=5.18394${\AA}$. The reaction rates of GaN were increased with both reaction time and temperature, however it did not depends on the flow rates of NH$_3$. The island type GaN crystals were grown on (0001) sapphire substrates and fast lateral growth of GaN on (111) Si substrate than sapphire was observed in our experiments.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.106-111
• /
• 2001

The freestanding GaN substrates were grown by hydride vapor phase epitaxy (HVPE) on (0001) sapphire substrate and prepared by using laser induced lift-off. After a mechanical polishing on both Ga and N-surfaces of GaN films with 100$\mu\textrm{m}$ thick, their polarities have been investigated by using chemical etching in phosphoric acid solution, 3 dimensional surface profiler and Auger electron spectroscopy (AES). The composition of the GaN film measured by AES indicted that Ga and N terminated surfaces have the different N/Ga peak ratio of 0.74 and 0.97, respectively. Ga-face and N-face of GaN revealed quite different chemical properties: the polar surfaces corresponding to (0001) plane are resistant to a phosphoric acid etching whereas N-polar surfaces corresponding to(0001) are chemically active.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.8
• /
• pp.713-719
• /
• 2002

In this study, the vertically well-aligned CNTs were synthesized by DC bias-assisted inductively coupled plasma hot-filament chemical vapor deposition (ICPHFCVD) using radio-frequence plasma of high density and that CNTs were vertically grown on Ni(300 )/Cr(200 )-deposited glass substrates at 58$0^{\circ}C$. This system(ICPHFCVD) added to tungsten filament in order to get thermal decompound and DC bias in order to vertically grow to general Inductively Coupled Plasma CVD. The grown CNTs by ICPHFCVD were developed to higher graphitization and fewer field emission properties than those by general ICPCVD. In this system, DC bias was effect of vortical alignment to growing CNTs. The measured turn-on fields of field emission property by general ICPCVD and DC bias-assisted ICPHFCVD were 5 V/${\mu}{\textrm}{m}$ and 3 V/${\mu}{\textrm}{m}$, respectively.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.954-957
• /
• 1999

We have synthesized carbon nanotubes by thermal chemical vapor deposition of $C_2$H$_2$ on transition metal-coated silicon substrates. Carbon nanotubes are uniformly synthesized on a large area of the plain Si substrates, different from previously reported porous Si substrates. It is observed that surface modification of transition metals deposited on substrates by either etching with dipping in a HF solution and/or NH$_3$ pretreatment is a crucial step for the nanotube growth prior to the reaction of $C_2$H$_2$gas. We will demonstrate that the diameters of carbon naotubes can be controlled by applying the different transition metals.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.5
• /
• pp.213-217
• /
• 2012

Carbon coils could be synthesized on nickel catalyst layer-deposited silicon oxide substrate using $C_2H_2$ and $H_2$ as source gases under thermal chemical vapor deposition system. By the incorporation of $SF_6$ additive in cyclic modulation manner, the dominant formation of the nanosized carbon coils could be achieved with maintaining the minimized sulfur additive amount. The geometry variation of the as-grown carbon coils, such as linear type, microsized coil type, wavelike nanosized coil type, and nanosized coil type, were investigated according to the different cyclic modulation manner of $SF_6$ flow. $SF_6$ gas incorporation develops the coil-type geometry. Furthermore, the higher flow rate of $SF_6$ gas increased the amount of the nanosized carbon coils. The slightly increased etching ability by $SF_6$ addition seems to be the cause for these results.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.477-484
• /
• 1994

The yttria stabilized zirconia(YSZ) thin films for solid oxide fuel cell (SOFC) were fabricated by an electrochemical vapor deposition(EVD) technique using YCl3+ZrCl4+H2O gas system. The YSZ films were deposited under reduced pressure at the temperature of 1000~120$0^{\circ}C$ on the porous alumina substrates. The deposition rate, chemical composition and growth morphology were investigated by SEM, XRD, EDS. The growth rates of the films obeyed a parabolic rate law, representing that the growing process is controlled by an electrochemical transport through the YSZ film. The Y2O3 content of the films was about 10 mol%, equal to the composition of metal chloride reactant gases, approximately. The YSZ films were highly dense, the growing features showed columnar structure and surface morphologies were changed with the EVD conditions.