• 대한조선학회논문집
• /
• 제50권4호
• /
• pp.248-254
• /
• 2013

In this paper, we establish an analysis algorithm and a design procedure for a Vane-Wheel which is a freely rotating device behind a propeller, by using a panel method. Vane-Wheel's function is to extract energy from the propeller slipstream in turbine part which is inner part of the Vane-Wheel, and convert this energy into an additional propulsive thrust in propeller part which is outer part of the Vane-Wheel. Two parts must satisfy torque balance and thrust has to act to the ship's forward direction. A Vane-Wheel has large interaction effect with propeller since it is placed behind of the propeller. Therefore, in order to consider interaction effect correctly, incoming velocity to the Vane-Wheel in a circumferential mean wake was calculated considering induced velocity from propeller to the Vane-Wheel. Likewise, incoming velocity to the propeller was calculated considering induced velocity from the Vane-Wheel to the propeller. This process is repeated until a converged result is obtained.

• 플랜트 저널
• /
• 제6권2호
• /
• pp.62-69
• /
• 2010

The stability of coal pulverizer in the 800 MW coal-fired plants is vital to maintain their performance. Thus, this study analyzed the uneven abrasion of the deflector and coal spillage due to the air velocity maldistribution in the vane wheel of a bowl-type pulverizer as it is a possible cause for problems of facility using pulverized coal. In addition, air flow in the underbowl of a bowl-type pulverizer was studied to check air velocity maldistribution in the vane wheel using numerical method. In an attempt to correct the maldistribution of air velocity, air flow of the modified duct vane was studied as enlarging the length of the duct vanes installed at the air inlet duct of the pulverizer and increasing the angle of inclination. It was found that modified duct vane make the velocity distribution at the vane wheel uniform. formed by the duct vanes installed at the air inlet duct of the pulverizer and swirling flow is the major factor in making the velocity distribution of vane wheel exit uniform. This can prevent the uneven abrasion of the deflector, which is one of the components inside the pulverizer and coal spillage.

• 대한기계학회논문집
• /
• 제16권5호
• /
• pp.974-982
• /
• 1992

본 연구에서는 Wheel 미립화기로 CWM을 분사시켰을때 Vane의 형태가 혼합연료 방울의 크기분포에 미치는 영향을 실험적으로 연구하는 것이며 그 연구 내용을 요약하 면 다음과 같다. .Vane의 형상계수(Aspect ratio)가 연료방울의 크기분포에 미치는 영향 .Vane의 각도가 연료방울의 크기분포에 미치는 영향 .미분탄 부하도와 연료방울의 SMD변화 .미분탄 분포의 평균크기변경에 따른 연료방울의 SMD변화 위에서 형상계수라함은 Vane의 출구직경(d)와 Vane의 출구길이 (L)의 비(L/d)를 의미 하고 있다.

• 한국유체기계학회 논문집
• /
• 제10권3호
• /
• pp.17-24
• /
• 2007

This paper presents the design procedure of a vertical wind turbine named jet-wheel-turbo turbine and the numerical and experimental verifications. The design parameters such as the rotor inlet angle, the diameter-to-hub ratio, the inlet guide outlet angle and the solidity were optimized to maximize the energy transfer, and to further increase the turbine efficiency by applying the side guide vane and the side opening to the rotor. The maximum power coefficient of 0.59, which is much higher than the ever-designed three-bladed horizontal turbines, was experimentally obtained when the optimal inlet- and side-guide vanes were installed and both sides of the rotor were 80% opened. The maximum power coefficients occur at the tip speed ratio ranging between 0.6 and 0.7. This vertical-axis turbine model can be applied to the large-scale power generation system with the speed and torque control algorithm for the specified wind characteristics.