• Journal of the korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.1-5
• /
• 1994

1) Natural gas engine에서 intake valve와 valve seat insert가 exhuast valve와 valve seat insert보다 마모가 심하다. 2) Ceramic valve seat insert을 금속재료를 사용하는 것이 보다 더욱 효과적이다. 즉 적어도 3배 정도 마모가 적게 일어난다. 3) Ceramic valve와 ceramic valve seat insert로 결합한 경우 valve face 또는 stem 부위에서 응력이 집중되어 파손된다. 따라서 현재의 ceramic valve design methodology로는 ceramic valve은 좋은 결과를 얻을 수 없다. 4) 가장 효과적인 결합은 Tribolloy 800의 hardfacing 합금의 valve와 질화규소의 valve seat insert이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.103-104
• /
• 2006

Wear of valve seating face and seat insert seating face influence the performance of engine, so they are important. To manufacture good quality valve and seat insert which have wear resistance the relations between wear factors and wear of the two seating faces have to be inspected. Cycle number is one of the important wear factors wearing the two seating faces and it can translate into mileage in rear car. But little is blown. Test variable is only cycle number and the cycle numbers are $2.0{\times}10^6,\;4.0{\times}10^6\;6.0{\times}10^6,\;8.0{\times}10^6$. And the other test conditions were fixed. Rmax of valve seating face and seat insert seating face increase linearly as cycle number is increased. Rmax of valve seating face were smaller than seat insert seating face in each cycle number. Reaction production by tribological reaction and sliding wear was found on the two faces.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.6
• /
• pp.108-115
• /
• 2008

The wear on engine valve and seat insert is one of the most important factors affecting engine performance. The engine valve and seat insert must be able to withstand the severe environment that is created by: high temperature exhaust gases generated while the engine is running, rapid movement of the valve spring, high pressure generated in the explosive process. In order to study such problems, a simulator has been developed to generate and control high temperatures and various speeds during motion. The wear simulator is considered to be a valid simulation of the engine valve and seat insert wear process with various speeds during engine activity. This work focused on the test of various degrees of wear on four different exhaust valve materials such as HRV40, HRV40-FNV (face nitrided valve), STL #32, STL #6,. Throughout all tests performed in this study, the outer surface temperature of the seat insert was controlled at $350^{\circ}C$, the cycle number was $4.0{\times}10^6$, the test load was 6860 N, the fuel was LPG the test speed was 20 Hz (2400 RPM) and the seat insert material was HVS1-2. The mean (standard deviation) maximum roughness of the exhaust valve and seat insert was $25.44\;(3.16)\;{\mu}m$ and $27.53\;(3.60)\;{\mu}m$ at the HRV40, $21.58\;(2.38)\;{\mu}m$ and $25.94\;(3.07)\;{\mu}m$ at the HRV40-FNV, $36.73\;(8.98)\;{\mu}m$ and $61.38\;(7.84)\;{\mu}m$ at the STL #32, $73.64\;(23.80)\;{\mu}m$ and $60.80\;(13.49)\;{\mu}m$ at the STL #6, respectively. It was discovered that the maximum roughness of exhaust valve was lower as the high temperature hardness of the valve material was higher under the same test conditions such as temperature, test speed, cycle number, test load and seat insert material. The set of the HRV40-FNV exhaust valve and the HVS1-2 seat insert showed the best wear resistance.

• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2052-2060
• /
• 2006

The wear of engine valve and seat insert is one of the most important factors which affect engine performance. Because of higher demands on performance and the increasing use of alternative fuel, engine valve and seat insert are challenged with greater wear problems than in the past. In order to solve the above problems, a simulator was developed to be able to generate and control high temperatures and various speeds during motion. The wear simulator is considered to be a valid simulation of the engine valve and seat insert wear process with various speeds during engine activity. This work focuses on the different degrees of wear at three different singular test speeds (10 Hz, 25 Hz & multi-Hz). For this study, the temperature of the outer surface of the seat insert was controlled at 350$^{\circ}C$, and the test load was 1960 N. The test cycle number was $6.0{\times}10^6$. The mean ($\pm$standard error) wear depth of the valve at 10 Hz and 25 Hz was 45.1 ($\pm$3.7)$\mu$m and 81.7 ($\pm$2.5)$\mu$m, respectively. The mean wear depth of the seat insert at 10 Hz and 25 Hz was 52.7 ($\pm$3.9)$\mu$m and 91.2 ($\pm$2.7)$\mu$m, respectively. In the case of multi-Hz it was 70.7 ($\pm$2.4)$\mu$m and 77.4 ($\pm$3.8)$\mu$m, respectively. It was found that higher speed (25 Hz) cause a greater degree of wear than lower speed (10 Hz) under identical test condition (temperature, valve displacement, cycle number and test load). In the wear mechanisms of valves, adhesive wear, shear strain and abrasive wear could be observed. Also, in the wear mechanisms of seat inserts, adhesive wear, surface fatigue wear and abrasive wear could be observed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.14-20
• /
• 2003

The minimization of valve and seat insert wear is a critical factor in the pursuit of engine performance improvement. In order to achieve this goal, we have developed a new simulator, which can generate and control high temperatures up to $900^{\circ}C$ and various speeds up to 80Hz during motion, just like an actual engine. The wear simulator is considered to be a valid simulation of the engine valve and seat insert wear process with various speeds during engine activity. The objective of this work focuses on the different degrees of wear from two different test speeds (10Hz & 25Hz). For this study, the temperature of the outer surface of the seat insert was controlled at $350^{\circ}C$, the cycle number was 2.1$\times$106, and the test load was 1960N. The wear depth and surface roughness were measured before and after the testing using a confocal laser scanner. It was found that a higher speed (25Hz) causes more wear than a lower speed (10Hz) under identical test conditions (temperature, cycle number and test load). In the wear mechanism adhesive wear, shear strain and abrasive wear could be observed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.403-404
• /
• 2006

Sintered materials have been applied widely in Valve Seat Inserts (VSI). The demands for VSIs are not only good heat and wear resistance but also good machinability. The sintered materials, which are made of a mixture of manganese containing iron powder and certain types of sulfide powder, have superior machinability due to precipitation of the fine MnS particles in the matrix. This report introduces a new VSI material, which has both superior machinability, and wear resistance due to applies of this "MnS precipitation" technique.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.391-392
• /
• 2006

Sintered materials have been applied widely in Valve Seat Inserts (VSI). The amount of wear on VSIs increases when used in gas (LPG, CNG) engines because of their dry environments. In this paper, two newly developed high performance VSI materials for gas engines are introduced. These materials applied new techniques, which are both high performance hard particle and new distribution method of solid lubricant, to increase wear resistance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.201-202
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.131-132
• /
• 2007