• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.593-598
• /
• 2000

Experimental study is conducted to clarify the pneumatic characteristics of brake system for freight train. Empty-load and diaphragm brake systems are mainly installed in the freight trains owned by KNR(Korean National Railroad). Experimental train set is composed of sixteen freight train and one diesel locomotive that are now in use. From the experimental results, in case of commercial brake, empty-load brake system responds to the brake command more slowly than the diaphragm brake system. But, in case of release command, the response time of diaphragm brake system is shorter than that of empty-load one. In the emergency brake test, the decreasing rate of brake pipe pressure of tenth car is almost same that of decreasing rate of commercial brake service.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.185-192
• /
• 2002

This paper focused on the dynamic behavior of camshaft in a direct acting type valve train system. To investigate camshaft behavior, transient vibration analysis is performed by using the transfer matrix method. The camshaft is treated as lumped mass system supported by spring and damper. Front the presented analytical model, we could predict dynamic behavior of camshaft, shaft locus within bearing and bearing load. The presented mode and results will be very helpful to design the optimal camshaft and valve train system.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.34-43
• /
• 2002

This paper focused on the dynamic behavior of camshaft in a direct acting type valve train system. To investigate camshaft behavior, transient vibration analysis is performed by using the transfer matrix method. The camshaft is treated as a lumped mass system supported by spring and damper, From the presented analytical model, we could predict dynamic behavior of camshaft, shaft locus within bearing and bearing load. The presented model and results will be very helpful to design the optimal camshaft and valve train system.

• 한국기계가공학회지
• /
• 제3권3호
• /
• pp.71-78
• /
• 2004

The loader of this study is an agriculture machine for a stock farmer. We has much researched about power train and steering system in order to develop a new stock machine. So, the loader developed in this study has a 4 wheel driving system and a 4-type wheel steering system. Though the technological region is some large and general, these technologies are very important and their technical life may be very long. The power train of the loader is consisted of many units as follows, engine, clutch, transmission, and axles. And, the 4-type wheel steering system is consisted of oil tank, oil pump, steering valve, solenold valve, electronic controller, hydraulic cylinders, and touch sensors. This study shows construction logics of power train and steering system. We could know from many working tests that the developed loader with 4-type steeling system has many advantages when driving in a narrow corral.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.837-844
• /
• 1986

본 논문에서는 우선 실제의 밸브기구를 잘 묘사하고, 감도해석을 적용하기 쉬 운 5자유도의 집중질량 모델을 만들었다. 그리고, 그 모델로부터 얻어지는 밸브양정 을 밸브기구의 고유값 및 고유벡터의 항으로 표시하고, 그것을 설계변수(모델에 포함 되어지는 질량, 강성계수)에 대하여 미분하여 밸브양정의 감도를 구하였다. 그리하 여, 밸브양정에 대한 설계변수들의 영향이 어느정도 되는가를 정량적으로 계산하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.505-506
• /
• 2007

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.397-405
• /
• 2000

Many computational researches have been performed about EHL film thickness in the contact between cam and follower. However, those computations do not explain the characteristics of dynamic film thickness which means squeeze film effect. Without the consideration of transient term in the Reynold's equation, the predicted film thickness has large difference from the actual film thickness. In this study, we have investigated the kinematic and dynamic simulations of rocker-arm valve train system. From the simulation, the applied load and the entraining velocity of the lubricant between cam and follower are obtained and with these values the dynamic film thickness is computed by Newton-Raphson method and compared with the steady state film thickness.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.163-171
• /
• 1998

Continuously contacting with camshaft the face of Valve Lifter made of cast iron brings about abnormal wear such as unfairwear or earlywear because it is heavily loaded in the valve train systems as the engine gets more powered. This abnormal wear becomes a defet namely over-clearance when the valve is lifting so that the fuel gas imperfectly combusted by unsuitable open or close aaction of the engine valve in the combustion chamber. The imperfect combustion in the end results in the major cause of air pollution and combustion chamber. The imperfectly combusted by unsuitable open or close action of the engine valve in the combustion chamber. The imperfect combustion in the end results in the major causes of air pollution and decrease of the engine output. Consequently to prevent this wear this study was to develop the valve lifter which is joined by brazing process with SCM435H and a tip by manufacturing the face as a superhardened which is joined by brazing process with SCM435H and a tip by manufacturing the face as a superhardened ceramics alloy which has high wear resistance. Having the excellent surface hardness with Hv1100-1200 the sintered body developed with superhardened alloy(WC) can endure the severe face loading in the valve train system. We experienced with various brazing alloys and obtained the excellent joining strength to the joint had 150MPa shear strength. Interface analysis and microstructure in a joint were examined through SEM & EDS Optical microscope. Also 2,500 hours high speed(3,000-4,000 rpm) and continuous (1step 12hr) engine dynamo testing was carried out to casting valve liter and ceramics-metal joint valve lifter so that the abnormal wears were compared and evaluated.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.105-111
• /
• 2003

The valve train system of engines has long been a sensitive area with respect to wear performance because of the high contact loads and surface sliding speeds encountered. In particular, wear problems of load-carrying components in relative motion, such as cam and tappet in valve train system have made troubles. To overcome these problems, combination of proper materials is important, as well as selecting of high wear performance materials. This paper presents the experimental result of friction and wear properties of ca/tappet materials. To investigate friction and wear properties for several combinations of materials, using commonplace tribometer(Plint 77, reciprocating type), we make a selection of a optimum material combination.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.119-124
• /
• 2001

As the brake control valve of freight car, there are sliding valve and diaphragm one. In this study, we measured and analyzed pneumatic characteristics of brake system of the freight car by using real train experiment. The difference of the release time appears in the freight car incorporated with sliding and diaphragm valve respectively. We adapted quick release valve to reduce the difference of the release time and also found that this valve is useful for the purpose.