• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.146-153
• /
• 2013

CNG buses has contributed to improve air quality in cities. But it is difficult to meet the next emission regulations such as EURO-VI without the help of additional post-processing device. Hydorgen has higher flame speed and lower combustion temperature that make it thermal efficiency increase with leaner operation. Using hydrogen natural gas blend (HCNG) fuel is promising technology which can reduce $NO_x$ and $CO_2$ emissions for a natural gas vehicle. However, fuel flow rate of HCNG should be increased since hydrogen's energy density per volume is much smaller than natural gas. In the present study, the characteristics of fuel supply system and its applicability were evaluated in a heavy duty natural gas engine. The results showed that the potential of fuel pressure regulator and fuel metering valve had enough capacity with HCNG. Employed mixer did not affect the distribution characteristics of mixture.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2015년도 임시총회 및 하계학술연구발표회
• /
• pp.156-157
• /
• 2015

we have presented the enhanced interlayer tunneling magnetoresistance in doped $La_{1+2x}Sr_{2-2x}Mn_2O_7$ single crystal below $T_C$. The drastically out-of-plane magnetoresistance observed in magnetic fields perpendicular to the bilayers indicates that spin-polarized magnetic layers in single crystal show as a stack of ordered spin valve.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 동계학술연구발표회 및 스핀트로닉스와 나노물리에관한 국제심포지움
• /
• pp.106-107
• /
• 2007

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2001년도 춘계연구발표회 논문개요집
• /
• pp.44-45
• /
• 2001

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1993년도 추계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.4-4
• /
• 1993

Ferrous powder metallurgy in Japan has developed in the last four decades, where every decade is featured by certain breakthroughs in materials. The progress in PM materials is closely related to newly developed powders. Low alloy steel powders for high strength PM components are grouped into three types: Ni and/or Mo containing completely alloyed powders, Ni containing partially alloyed powders, and Cr containing completely alloyed powders. Every type has its special characteristics. The tensile strength of PM materials is improved up to 2 GPa. The hardness is also increased to exceed 500 HV with normal hardening methods, and 700 HV with novel surface treatment techniques. The present maximum of fatigue strength is 550 MPa, and that of impact energy is 100 J. Novel PM materials with improved properties are applied to a variety of automobile and other components: power steering pumps, rocker anns, valve guides and inserts, bearings, torque sensors, etc. The future outlook for the ferrous PM is Quite positive, and the industry is expected to show renewed growth by applying many types of alloy steel powders and new ferrous PM materials.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2005년도 동계학술연구발표회 및 2차 아시안포럼
• /
• pp.78-79
• /
• 2005

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.188-191
• /
• 2007

This paper shows the Development of In-tank pressure regulator and Solenoid Valve used in FCV(Fuel Cell Vehicle). We have developed new type of Regulator and Solenoid through analysis of the structure and characteristics of component of FCS(Fuel Cell System) from the advanced technology. Now it is possible to localize the component by making use of the development of Regulator and Solenoid made by us. Regulator and Solenoid is a equipment to control hydrogen pressure supplied into a stack. Therefore, outlet pressure, a flow of fluid and temperature are important parameters according to a inlet pressure. And leak test, endurance test and burst test should be done to guarantee the performance and safety of Regulator and Solenoid used in the fuel of high pressure. Also, Hydrogen friendly materials are applied to inner parts of the Regulator, Solenoid and weight reduction is done to cost saving in part not related to performance. As a result, we have proven the good performance and reliability in endurance of Regulator, Solenoid and will make an development in performance as well as durability to ensure industrialization.

• Journal of Mechanical Science and Technology
• /
• 제20권3호
• /
• pp.358-365
• /
• 2006

The hydraulic pump of an Electro-hydrostatic Actuator should be able to quickly feed large volume of oil into hydraulic cylinder in order to reduce the response time. On the other hand, it should be also able to precisely dispense small amount of oil through low-speed operation so that the steady state position control error of the actuator can be accurately compensated. Within the scope of axial piston type hydraulic pumps, this paper is focused on the investigation how the surface treatment of their cylinder barrel with TiN plasma coating can contribute to the reduction of the friction and wear rate of valve plate in the low-speed range with mixed lubrication. The results showed that the friction torque of the valve plate mated with a TiN coated cylinder barrel could be reduced to 22% of that with an uncoated original one when load pressure was 300 bar and rotational speed 100 rpm. It means that the torque efficiency of the test pump was expected to increase more than 1.3% under the same working condition. At the same time, the wear rate of the valve plate could be reduced to $40\sim50%$.

• 소성∙가공
• /
• 제22권8호
• /
• pp.442-449
• /
• 2013

The solenoid valve case of an 8-speed automatic transmission plays a role in maintaining the valve seal, which prevents an inflow of foreign substances into the transmission. The seal increases the reliability of the automatic transmission's performance. As a solution to pollution-related problems and to reduce fuel consumption, transmissions are being made with more gears to work more economically and have reduced fuel consumption. These newer transmission require greater dimensional tolerances and need to be manufactured with more precision. In the current study, the design of a multistage drawing considering both the product's height and limit draw ratio (LDR) of the material was performed using both a theoretical analysis and the expertise of industrial experts. The finite element modeling (FEM) simulation was performed using the commercial software, PAM-stamp, and tests of the dimensional measurements for a prototype were performed to verify the optimal progressive process.

• Journal of Magnetics
• /
• 제2권3호
• /
• pp.96-100
• /
• 1997

A spin valve structure of NiO(40 nm)/Co(2 nm)/Cu(2.6 nm)/Co(x nm)/Ta(5 nm) has been investigated for the application of magnetic random access memory (MRAM). The spin valve structure exhibited very large difference in the coercivities between pinned and free layers, a relatively high GMR ratio, and a low free layer coercivity. The spin valves were prepared by sputtering and were characterized by dc 4-point probe, and VSM. The spin valves with combined free layer exhibited a maximun GMR ratio of 10.4% with a free layer coercivity of about 82 Oe. The spin valves with a single 10 nm thick a-CoNbZr free layer exhibited a GMR ratio of about 4.3% with a free layer coercivity of about 12 Oe. The GMR ratio of the spin valves increased by addition of Co between Cu and a-CoNbZr. It has been confirmed that the coercivity of free layer can be decreased by increasing the thickness of a-CoNbZr. It has been confirmed that the coercivity of free layer can be decreased by increasing the thickness of a-CoNbZr layer without losing the GMR ratio substantially, which was mainly due to high resistivity of the amorphous "layers".