• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.360-364
• /
• 1994

This paper is concerned with extracting the diagnostic signature for motor-operated valves (MOV's) noninvasively. A torque estimator is developed and tested to obtain electical torque of the induction motors which are attached to the MOV's. Inverse filter is used to recover the gear meshing forces from the measured actuator housing vibration, which contain the gear rotation information. Frequency demodulation techniques are performed and an adaptive linear bandpass filter is implemented to improve signal-to-noise ratio. Finally, stand-alone valve experiments are carried out to validate the signature extraction scheme.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.111-112
• /
• 2006

A new MR cylinder with built-in valves using Magneto - Rheological fluid (MR valve) is proposed for fluid power control systems. The MR fluid is a newly developed functional fluid whose obvious viscosity is controlled by the applied magnetic field intensity. This MR cylinder, which is composed of cylinder with small clearance and piston with electromagnet, has the characteristics of simple, compact and reliable structure. This paper presents a method to control the pressure of MR cylinder by using Generalized Predictive Control (GPC) algorithm. The differential pressure is controlled by applying magnetic field intensity to MR fluid. The use of GPC controller is to generate a control sequence by minimizing a cost function in such a way that the future system output is driven close to reference over finite prediction horizons. Experimental results from real time control using GPC method compared with conventional PID control method are also shown in this paper.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.6
• /
• pp.397-402
• /
• 2016

To produce adequate electricity in nuclear and thermal power plants, an optimal amount of steam should be supplied to a generator connected to high- and low-pressure steam turbines. A turbine output control device, which is a special steam valve employed to supply or interrupt the steam to the turbine, is operated using a hydraulic servo actuator. In power plants, the performance of servo actuators is degraded by the air generated from the hydraulic system, or causes frequent failures owing to an increase in the wear of the seal. This is due to the seal being burnt as generated heat using the produced compressed air. Some power plants have exhausted air using a fixed orifice, and thus they encounter power loss due to mass flow exhaust. Failures are generated in hydraulic pumps, electric motors, and valves, which are frequently operated. In this study, we perform modeling and analysis of the load-sensing air-exhaust valves, which can be passed through very fine flow under normal use conditions, and exhaust mass flow air at the beginning stage as with existing fixed orifices. Then, we propose a method to prevent failures due to the compressed air, and to ensure the control accuracy of hydraulic servo actuators.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.296-300
• /
• 2004

A new MR cylinder with built-in valves using MR fluid (MR valve) is proposed for fluid power control systems. The MR or Magneto-Rheololgical fluid is a newly developed functional fluid whose obvious viscosity is controlled by the applied magnetic field intensity. The MR cylinder is composed of cylinder with small clearance and piston with electromagnet. The differential pressure is controlled by the applied magnetic field intensity. It has the characteristics of simple, compact and reliable structure. The size of MR cylinder and piston has ${\varphi}$60mm${\times}$259mm and ${\varphi}$58mm${\times}$136.5mm in face size respectively and 0.8mm in gap length. Through experiments on the static characteristics, it is found that the differential pressure is controlled by the applied magnetic field intensity under little influence of the flow rate, which corresponds to a pressure control valve. Effectiveness of the MR cylinder is demonstrated through the position control of one link MR manipulator.

• Journal of Drive and Control
• /
• v.13 no.4
• /
• pp.31-44
• /
• 2016

In recent hydraulic actuation systems, conventional hydraulic spool valves with pressure compensators are becoming less popular, after the introduction of the independent metering concept for valves. Within this concept, four valves are needed for actuating a single cylinder. Subsequently, this increases the freedom of controlling both chamber pressures of the cylinder, and it then provides for electronically-controlled pressure compensation facilities. Additionally, this has the potential to save valuable energy. The primary focus of this paper is to develop a new generation of hydraulic circuits using the independent metering valve (IMV). This configuration can function well as a conventional IMV circuit while providing better pressure control. We first describe the working principles of five distinct modes of the proposed IMV system. Then, mathematical models for each working mode are presented. Finally, we present numerical simulations that have been carried out to evaluate the system performance, in comparison with that of the conventional IMV configuration. The simulation results demonstrate that the performance of the new IMV configuration is superior to the conventional IMV system in terms of energy savings.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.32-40
• /
• 1994

A digital control system for the steam generator oater level control is developed using the optimal control technique. To describe the more realistic situation, a feedwater valve actuator of the first order lag is included in the overall control system. The optimal gains are obtained by the LQ method which imposes the constraints on the feedwater valve motion as well as on the deviation between the input demand signal and the output feedwater. Developed also is a Kalman observer on account of the flow measurement uncertainty at low power. And a digital controller on the feedback loop is designed which makes the system maintain the same stability margins for all power ranges. The simulation results show that the optimal digital system has good control characteristics despite the adverse dynamics of the steam generator at low power.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.111-115
• /
• 2009

The method of test for observing the combustion instability and controling the instability actively by using secondary injection of fuel through flame stabilizer was studied by constructing model combustor of supersonic engine. The frequency of combustion instability was detected by measuring the pressure of combustor using pressure sensor and by optical sensing of flame intensity. Electro-magnetic valve was adopted as actuator for active control and the characteristics of modulated fuel was studied by measured pressure of valve outlet and scattering signal of spray at secondary fuel injection.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.4
• /
• pp.320-326
• /
• 2000

The real-time simulator of a pneumatic actuation system that is composed of differential PWM signal generator, charge solenoid valve, discharge solenoid valve, actuator, load, and rotational potentiometer is developed using a DSP board and a PC. The simulator receives the control signals from the external controller through the A/D converter, updates the state and output variables of the Pneumatic actuation system responding to the input signals every sampling time, and sends out the output signals through the D/A converter in real time. The user can observe the displacements, velocities, pressures, and mass flows representing the operation of pneumatic actuation system through the PC monitor in real time. Also the user can see the moving images between the pistons and rotating arm realistically in real time. The accuracy of the real-time simulator is verified by the good agreement of the real-time simulation results and the experimental results of the pneumatic actuation system.

• Journal of Power System Engineering
• /
• v.13 no.5
• /
• pp.18-24
• /
• 2009

This paper shows the result of development about the revolution system of azimuth thruster which of power is less than 250kW for small ship. Advanced Azimuth revolution system can revolve propeller and rudder from 360 degree so that this system for vessel maneuvering can be excellent of propulsion effectively. Fluid power control system for azimuth thruster is designed with PID control system by using CEMTool/SIMTool program. And the actuator used for servo valve can control rudder angle, pressure and direction. The first, We had a test for the angle control of revolution system. The result of angle control confirmed that it has the good efficiency from experiment result of time input degree $30^{\circ}$, $90^{\circ}$ and $180^{\circ}$. The second, We had to a test for the pressure characteristic of hydraulic motor. As a result, We confirmed the maximum pressure 3.5MPa and steady state 0.7MPa nom experiment result of time input degree $30^{\circ}$. In this paper, it is identified the pressure characteristic of hydraulic motor and angle control for azimuth thruster by AMESim, and it has been confirmed the usefulness of AMEsim modeling was verified by comparison between AMESim simulation results and experiments results.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.194-199
• /
• 2001

In this paper, we propose a new locomotive mechanism using impulsive force for microcapsule-type endoscope. It has the compact size for movement in the colon and actuating mechanisms for hi-directional movement. The actuating mechanism resembles a pneumatic cylinder and consists of body, inertia mass(piston). spring. pneumatic source and calve. When valve is ON, the pneumatic impulsive force between piston and body drives them in two opposite direction. As the air in the body is passed away, the contrary movements are occurred by spring reaction. Therefore, the direction of body's motion is determined by the relative magnitude of two opposite impulsive forces, i.e., pneumatic and spring force. The effect of two impulsive forces can simply be controlled by On-Off time of solenoid valve.