• 대한치과보철학회지
• /
• 제45권1호
• /
• pp.71-84
• /
• 2007

Statement of problem: Implant surface characteristics plays an important role in clinical success and many studies have been made for improvement of success by changing surface roughness. Purpose: Appropriate increase of surface roughness increases the activity of osteoblast and enhance contact and retention between bone and implant. Material and method- Machined, SLA and RBM surface implants, which are the most commonly used implants were implanted into the tibia of rabbits and after 1 week, 4 weeks, 8 weeks and 12 weeks there were histologic and histomorphometric analysis and study for bone gradient and change of Ca/P ratio using EDS(Energy Dispersive X-ray Spectroscope). Results: Comparison of bone-implant contact showed no significant difference among each implant. In comparison of bone area rates, SLA showed higher value with significant difference at 1 week and 4 weeks, and SLA and RBM at 8 weeks than Machined implant (p<0.05). In analysis of bone constituents with EDS, titanium was specifically detected in new bones and the rates were constant by surface treatment method or period. In case of Ca/P ratio, according to surface treatment method, each group showed significant difference. Lots of old bone fragments produced during implantation remained on the rough surface of RBM implant surface and each group showed histological finding with active synthesis of collagen fibers until 12 weeks. In transmission electronic microscopic examination of sample slice after elapse of twelve weeks, tens nm of borderline (lamina limitans like dense line)was seen to contact the bone, on the interface between bone and implant. Conclusion: SLA and RBM implant with rough surface shows better histomorphometrical result and the trend of prolonged bone formation and maturation in comparison with Machined implant. In addition, implant with rough surface seems to be helpful in early stage bone formation due to remaining of old bone fragments produced in implantation. From the results above, it is considered to be better to use implant with rough surface in implantation.

• 항공우주기술
• /
• 제8권2호
• /
• pp.140-148
• /
• 2009

발사체 추진시스템에서 CC(Combustion Chamber) 산화제 개폐밸브는 액체산소를 연소기로 공급 및 차단함으로써 연소를 개시 및 중단시킬 뿐만 아니라, 정상운영 상태에서는 연소기 내 안정된 연소가 가능하도록 일정한 유량의 액체산소를 공급한다. CC 산화제 개폐밸브 개발과 관련하여, TM(Technology Model)의 극저온 산화제 개폐밸브를 제작하여, 밸브의 정상적인 작동성능을 이미 확인한 바 있다. 반면 TM의 유량계수, Cv가 설계기준 값보다 상당히 작았기 때문에, 차기 개발 단계인 CC 산화제 개폐밸브 EM(Engineering Model)의 설계/제작을 통해 충분히 개선된 Cv 특성을 확보하기 위해 CFD 해석을 수행하였다. CFD 해석 결과, 밸브 출구 각도를 120o로 변경하고, 밸브의 부분적인 크기 증가와 스트록 길이를 증가시킴으로써 EM의 Cv를 상당히 향상시킬 수 있는 것으로 확인되었다. 유량시험을 통해 측정된 EM의 개선된 Cv는 최소 212로써, 기존 TM의 Cv값인 161보다 32%가량 증가된 것을 확인하였다.

• 한국정보전자통신기술학회논문지
• /
• 제8권5호
• /
• pp.345-353
• /
• 2015

소프트웨어 디버깅과정에서 오류의 발생 시간에 기초한 많은 소프트웨어 신뢰성 모형이 이미 연구되었다. 유한고장모형과 비동질적인 포아송과정을 이용하면 소프트웨어의 신뢰성 모형에 대한 모수 추정을 가능하게 한다. 소프트웨어를 사용자에게 인도하는 경우 인도시기를 결정할 때 조건부 고장률은 중요한 변수가 된다. 이러한 유한 고장 모형은 실제 다양한 상황에서 사용될 수 있다. 특성화 문제, 이상치의 검출, 선형 추정, 시스템 신뢰성 연구, 수명 시험, 생존 분석, 데이터 압축 및 많은 다른 분야의 연구에서 이들의 사용은 많은 연구에서 볼 수 있다. 통계 공정 관리(SPC)는 소프트웨어 오류의 예측을 모니터링 함으로써 소프트웨어의 신뢰성의 향상에 크게 기여할 수 있다. 관리도는 널리 소프트웨어 업계에서 소프트웨어 품질관리에 사용된다. 본 논문에서는 NHPP와 다항 위험 함수의 평균값을 기초한 관리 메카니즘을 제시하였다.

• Earthquakes and Structures
• /
• 제11권6호
• /
• pp.1123-1141
• /
• 2016

To explore the application of traditional tuned mass dampers (TMDs) to the earthquake induced vibration control problem, a pounding tuned mass damper (PTMD) is proposed by adding a viscoelastic limitation to the traditional TMD. In the proposed PTMD, the vibration energy can be further dissipated through the impact between the attached mass and the viscoelastic layer. More energy dissipation modes can guarantee better control effectiveness under a suite of excitations. To further reduce mass ratio and enhance the implementation of the PTMD control, multiple PTMDs (MPTMD) control is then presented. After the experimental validation of the proposed improved Hertz based pounding model, the basic equations of the MPTMD controlled system are obtained. Numerical simulation is conducted on the benchmark model of the Canton Tower. The control effectiveness of the PTMD and the MPTMD is analyzed and compared under different earthquake inputs. The sensitivity and the optimization of the design parameters are also investigated. It is demonstrated that PTMDs have better control efficiency over the traditional TMDs, especially under more severe excitation. The control performance can be further improved with MPTMD control. The robustness can be enhanced while the attached mass for each PTMD can be greatly reduced. It is also demonstrated through the simulation that a non-uniformly distributed MPTMD has better control performance than the uniformly distributed one. Parameter study is carried out for both the PTMD and the MPTMD systems. Finally, the optimization of the design parameters, including mass ratio, initial gap value, and number of PTMD in the MPTMD system, is performed for control improvement.

• Asian-Australasian Journal of Animal Sciences
• /
• 제20권4호
• /
• pp.529-535
• /
• 2007

The nutritive values of leaves of Citrus grandis, Citrus aurantium, Citrus oranges, Citrus limon, and Citrus deliciosa were evaluated by chemical composition and in vitro gas production techniques. There were significant (p<0.001) differences among citrus species in terms of chemical composition. Crude protein (CP) contents ranged from 123.0 to 148.3 g/kg DM. Neutral detergent fibre (NDF) and acid detergent fibre (ADF) contents were varied with species in the range 219.4-355.4 and 215.0-278.8 g/kg DM respectively. Condensed tannin (CT) contents were ranged from 5.9 to 10.2 g/kg DM. The PEG addition significantly (p<0.001) increased the gas production and some estimated parameters of citrus tree leaves. However, species showed variable responses to polyethylene glycol (PEG) treatment. There were also significant (p<0.001) differences among species in terms of gas production and estimated parameters. The OMD and ME contents of citrus leaves without PEG supplementation were ranged from 66.5 to 73.3% and 9.8 to 10.9 MJ/kg DM respectively. The improvement in gas production, organic matter digestibility (OMD) and metabolizable energy (ME) with PEG emphasized the negative effect of tannins on digestibility. The increase (%) in the estimated OMD and ME contents ranged from 5.5 to 9.8% and 5.7 to 10.2% respectively. All citrus tree leaves studied in this experiment have potential nutritive values indicated by high crude protein content, OMD, ME and low fiber values.

• Asian-Australasian Journal of Animal Sciences
• /
• 제25권4호
• /
• pp.479-485
• /
• 2012

In order to develop methods that would enlarge the feed resources in Tibet, mixtures of hulless-barley straw and tall fescue were ensiled with four levels (0, 10%, 20%, and 30% of fresh weight) of wet hulless-barley distillers' grains (WHDG). The silos were opened after 7, 14 or 30 d of ensiling, and the fermentation characteristics and nutritive quality of the silages were analyzed. WHDG addition significantly improved fermentation quality, as indicated by the faster decline of pH, rapid accumulation of lactic acid (LA) (p<0.05), and lower butyric acid content and ammonia-N/total N (p<0.05) as compared with the control. These results indicated that WHDG additions not only effectively inhibited the activity of aerobic bacteria, but also resulted in faster and greatly enhanced LA production and pH value decline, which restricted activity of undesirable bacteria, resulting in more residual water soluble carbohydrates (WSC) in the silages. The protein content of WHDG-containing silages were significantly higher (p<0.05) higher than that of the control. In conclusion, the addition of WHDG increased the fermentation and nutritive quality of straw-grass silage, and this effect was more marked when the inclusion rate of WHDG was greater than 20%.

• Asian-Australasian Journal of Animal Sciences
• /
• 제26권5호
• /
• pp.603-608
• /
• 2013

Hanwoo have been subjected over the last seventy years to intensive artificial selection with the aim of improving meat production traits such as marbling and carcass weight. In this study, we performed a signature of selection analysis to identify recent positive selected regions driven by a long-term artificial selection process called a breeding program using whole genome SNP data. In order to investigate homozygous regions across the genome, we estimated iES (integrated Extended Haplotype Homozygosity SNP) for the each SNPs. As a result, we identified two highly homozygous regions that seem to be strong and/or recent positive selection. Five genes (DPH5, OLFM3, S1PR1, LRRN1 and CRBN) were included in this region. To go further in the interpretation of the observed signatures of selection, we subsequently concentrated on the annotation of differentiated genes defined according to the iES value of SNPs localized close or within them. We also described the detection of the adaptive evolution at the molecular level for the genes of interest. As a result, this analysis also led to the identification of OLFM3 as having a strong signal of selection in bovine lineage. The results of this study indicate that artificial selection which might have targeted most of these genes was mainly oriented towards improvement of meat production.

• 한국농촌생활과학회지
• /
• 제7권2호
• /
• pp.99-108
• /
• 1996

This study has intended to suggest fundamental data to develope and choose appropriate shoes for upland farming in order to prevent health deterioration of women workers and improve work effectiveness and reduce fatigue by wearing appropriate shoes. During 1995. 4. 28 - 5. 10, Fifty women workers in hot pepper farming were observed and major shoe types, which were rubber shoes, walking shoes, slippers, and rubber boots, were selected for the study. During 1995. 10. 9 - 31, two subjects were tested by wearing those shoes in the laboratory where the temperature was 24$\pm$1$^{\circ}C$ and relative humidity 50$\pm$5%RH. And the temperature & humidity on sole and in the shoes, the rectal temperature, skin temperature, blood pressure, pulse, lactate concentration of blood, Flickers' value and subjective sensation were measured. The results were as follows : 1. 84% of women workers mentioned that they need shoes improvement and the order of most frequent shoe types to be worn was rubber shoes, walking shoes, slippers, rubber boots. 2. The rate of women who were unsatisfied with shoes for upland farming is 38 percentages. The reason of unsatisfaction was that feet were in a sweat and alien substances were let into shoes. 3. The temperature & humidity on sole were the lowest in rubber boots during experiment(p＜0.01). 4. The relative humidity in the shoes was the highest in rubber boots by 90% and the lowest in walking shoes by 72% during rest And the humidity in slippers and walking shoes were significantly low in experiment(p＜0.001). 5. Rubber boots showed the highest rise in rectal temperature by 0.2$^{\circ}C$ showing increase of core temperature (p＜0.05). 6. The mean skin temperature during experiment was highest in rubber boots by 33.8$^{\circ}C$(p＜0.001).

• Journal of Mechanical Science and Technology
• /
• 제18권1호
• /
• pp.74-81
• /
• 2004

The KSNP Steam Generators (Youngkwang Unit 3 and 4, Ulchin Unit 3 and 4) have a problem of U-tube fretting wear due to Flow Induced Vibration (FIV). In particular, the wear is localized and concentrated in a small area of upper part of U-bend in the Central Cavity region. The region has some conditions susceptible to the FIV, which are high flow velocity, high void fraction, and long unsupported span. Even though the FIV could be occurred by many mechanisms, the main mechanism would be fluid-elastic instability, or turbulent excitation. To remedy the problem, Eggcrate Flow Distribution Plate (EFDP) was installed in the Central Cavity region or Ulchin Unit 5 and 6 steam generators, so that it reduces the flow velocity in the region to a certain level. However, the cause of the FIV and the effectiveness of the EFDP was not thoroughly studied and checked. In this study, therefore the Stability Ratio (SR), which is the ratio of the actual velocity to the critical velocity, was compared between the value before the installation of EFDP and that after. Also the possibility of fluid-elastic instability of KSNP steam generator and the effectiveness of EFDP were checked based on the ATHOS3 code calculation and the Pettigrew's experimental results. The calculated results were plotted in a fluid-elastic instability criteria-diagram (Pettigrew, 1998, Fig. 9). The plotted result showed that KSNP steam generator with EFDP had the margin of Fluid-Elastic Instability by almost 25％.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권6호
• /
• pp.914-921
• /
• 2010

연약지반에 구조물을 시공시 지반의 지지력 약화에 의해 지반침하가 발생한다. 이를 방지하기 위하여 연약지반의 개량이 요구될 뿐만아니라 합리적인 시공관리를 위하여 침하량 예측이 선행되어야 한다. 본 연구에서는 구조물 설계 및 시공 초기단계에서 지반의 침하량을 예측하기 위해 인공신경망을 이용하였다. 인공신경망을 이용하여 대상지역의 원지반에서 발생하는 침하량과 D.C.M공법을 적용하여 개량된 지반에서 발생하는 침하량을 예측하고, 대상지역의 침하거동 및 침하량을 Mohr-Coulomb모델을 이용한 연속체 해석 결과와 인공신경망을 수행한 결과를 비교하였다. 그 예측결과 D.C.M이 적용된 지반이 원지반보다 0.8배 감소한 침하량을 보였다. 연속체 해석과 인공신경망을 이용해 도출된 결과는 결정계수 0.79로 비교적 높은 상관관계를 보였다. 따라서 본 연구는 연약지반 개량공법의 침하량 예측이 실내실험자료를 통해 평가하는 것이 가능하다는 것을 확인하였다.