• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.2
• /
• pp.85-92
• /
• 1998

The hydrogenation behavior of $Mg_2Ni$ powder prepared by ball milling has been studied. Ball milled $Mg_2Ni$ was transformed to an amorphous-like state after 200hr ballmilling, and crystallized to $Mg_2NiH_x$ by hydrogenation at got. The hydrogen storage capacity gradually increased as a function of ball milling time. $Mg_2Ni$ by 400hr ballmilling shows higher hydrogen storage capacity (3H/M) than $Mg_2Ni$ by VIM(Vacuum Induction Melting).

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.190-197
• /
• 1994

The densification behavior during a sintering of M2 and T15 grade high speed steel powder compacts was reported. Sintered densities over 98% theoretical were achieved by a liquid phase sintering in vacuum for both grades. The optimum sintering temperature range where full densification could be achieved without excessive carbide coarsening and incipient melting was much narrower in M2 than in T15 grade. The sintering response was mainly affected by the type of carbides present. The primary carbides in M2 were identified as $M_6C$ type whereas those in T15 were MC type which provides wider sintering range. The addition of elemental carbon up to 0.3% lowered the optimum sintering temperature for both grades, but had little effect on expanding the sintering range and sintered structure.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.186-186
• /
• 2014

In this study, corrosion behaviors of Ti-xNb alloys for biomaterials. The Ti-xNb binary alloys contained from 10 wt. % to 50 wt. % contents were manufactured by vacuum arc-melting furnace. Microstructures of the alloys were examined by optical microscope (OM) and field emission scanning electron microscope (FE-SEM). In order to identify the phase constitutents of the Ti-xNb alloys, X-ray diffractometer (XRD) with a Cu K radiation was used. The corrosion behaviors were investigated using potentiostat (Model2273,EG & GCo, USA) in NaCl solution at $(36.6{\pm}1.0)^{\circ}C$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.187-187
• /
• 2014

In this study, we investigated mechanical properties and surface characteristics of Ti-25Ta-xHf alloys. The samples were manufactured for composition of Ti-25Ta-xHf(x=0 to 15 wt. %) alloys. Each alloy was melted twenty times in an arc-melting vacuum furnace. The microstructural phases and phase transformation of Ti-25Ta-xHf alloys were identified with the aid of an XRF, XRD and DSC. And mechanical properties were investigated using Vickers hardness, nanoindentation, and tensile test.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.32-40
• /
• 1997

Solid state diffusion bonding is the joining process performed by creep and diffusion, which is accelerated by heating below melting temperature and proper pressing, in vacuum or shielding gas atmosphere. By this process we can obtain sufficient joint which can't be expected from the fusion welding. For Ti-6Al-4V alloy, the optimum solid state diffusion bonding condition and mechanical properties of the joint were found, and micro void morphology at bond interface was observed by SEM. The results of tensile test showed sufficient joint, whose mechanical properties are similar to that of base metal. 850$^{\circ}$C, 3MPa is considered as the optimum bonding condition. Void morphology at interface is long and flat at the initial stage. As the percentage of bonded area increases, however, small and round voids are found. Variation of void shape can be explained as follows. As for the void shrinkage mechanism, at the initial stage, power law creep is the dominant, but diffusion mechanism is dominant when the percentage of bonded area is increased.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.149-153
• /
• 2016

Thermal oxidation has significant potential for use in synthesizing metal-oxide nanostructures from metallic materials. However, this method has limited applicability to the synthesis of multi-morphology NiO from Ni foil. Techniques consisting of mechanical and chemical approaches were used to pre-treat the Ni foil (prior to oxidation) to promote the formation of nanowires and nanoplates on the NiO layer. These morphologies were realized on the Ni foils scratched by sand paper and a knife, respectively, and subsequently heat-treated at $500^{\circ}C$ for 24 h. Small nanowires (diameter: <10 nm) formed on the Ni foil treated by absolute $HNO_3$ and then oxidized at $500^{\circ}C$ for 24 h. The formation of various morphologies (on the pre-treated Ni foil), which differ from that formed in the case of pristine Ni foil after oxidation, may be attributed to the surface melting phenomenon that occurs during the nucleation process.

• Journal of the Korean Chemical Society
• /
• v.8 no.2
• /
• pp.57-61
• /
• 1964

It was verified at Part Ⅰ of this investigation that there is a minimum wettability between molten iron and graphite, which was preliminarily coated with magnesium, and thus the spheroidization of graphite might have resulted from the lack of wettability between magnesium-adsorbed graphite and iron matrix. Being continued from the last work, the wettability between pure iron and graphite, coated with the various thickness of cerium, are measured at melting point of pure iron in vacuum and 200 mmHg argon gas atmosphere. The result indicates the presence of a minimum wettability at a critical thickness of cerium film as was proved in the case of magnesium. The experimental analysis shows that, the minimum wettability could be attributed entirely to a minimum work of adhesion between liquid iron and graphite at a critical concentration of cerium in the iron-graphite interface.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.58-63
• /
• 2004

The oxidation behavior of Ti-Nb alloys was studied in dry atmosphere. After vacuum arc melting and hot rolling treatment, Ti-Nb alloys were oxidized at $450^{\circ}C$∼$750^{\circ}C$. The oxidation behaviors between matrix and oxide scale were analyzed by SEM, XPS and XRD. Ti-Nb alloys had higher oxidation resistance than pure Ti at $750^{\circ}C$. XPS analysis of oxide film revealed that $TiO_2$ oxide was formed on the top of surface. The weight gains during the oxidation increase rapidly at temperature above $600^{\circ}C$ which obey the parabolic law.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.106-106
• /
• 2015

In this study, we investigated electrochemically formed nanotube shape on ternary Ti-25Ta-xHf alloys with Hf contents. Ti-25Ta-xHf (x=0~15 wt.%) alloys were manufactured by vacuum arc-melting furnace. The obtained ingots were homogenized in an argon atmosphere at $1050^{\circ}C$ for 2h and then water quenching. The specimens were cut from ingots to 4 mm thickness and first ground and polished using SiC paper (grades from #100 to #2000). The anodization treatments on Ti-25Nb-xHf alloys were carried out at room temperature for experiments. The formation of nanotubular film was conducted by electrochemical method in mixed electrolytes with 1 M $H_3PO_4$ + 0.8 wt. % NaF at 30 V for 2 h. The morphologies of nanotube depended on the Hf content in Ti-25Ta-xHf ternary system.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.5
• /
• pp.365-372
• /
• 2000

Pure $Fe_3$Al alloys with three different compositions of Fe-21.8%Al, Fe-24.1%Al and Fe-27.2%Al were prepared by vacuum induction melting followed by homogenization and hot forging. The long-time oxidation behavior of the prepared alloys was studied at 1073, 1273 and 1473k in air. The oxidation resistance greatly increased with an increase in Al contents. Thin and uniform oxide scales were always formed on Fe-27.2%Al, while thick and fragile oxide scales were formed on Fe-(21.8, 24.1%)Al. Internal oxidation was observed in Fe-(21.8, 24.1%)Al, when oxidized above 1273K. The major oxidation product of all the oxidized alloys was always $\alpha$-$Al_2$$O_3$.