• International journal of advanced smart convergence
• /
• v.11 no.4
• /
• pp.88-95
• /
• 2022

Vacuum simulation is associated with the prediction and calculation of how materials, pumps and systems will perform using mathematical equations. In this investigation, three different high vacuum systems were simulated and estimated with each vacuum characteristics by VacTran simulator. In each of modelled vacuum systems, selection of gas loads into vessel, combination of rough and high vacuum pumps and dimension of conductance elements were proposed as system variables. In pump station model, the pumping speed to pressures by the combination of root pump was analyzed under the variations of vessel volume. In this study, the effects of outgassing dependent on vessel materials was also simulated and aluminum vessel was estimated to optimum materials. It was obtained from the modelling with diffusion pump that the diameter, length of 50×250[mm]roughing line was characterized as optimum variables to reach the ultimate pressure of 10E-7[torr]. Optimum design factors for vacuum characteristics of modelled vacuum system were achieved by VacTran simulator. Feasibility of VacTran as vacuum simulator was verified and applications of VacTran in high tech process expected to be increased.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.520-527
• /
• 2000

In the present study, the analytical approaches of vacuum consolidation with horizontal drains were proposed, For dissipating rapidly pore-water in hydraulic fills, vacuum consolidation method applied vacuum pressure in horizontal drains is developed. In the analytical approaches, the governing equation is based on two-dimensional finite strain consolidation theory and the boundary conditions of horizontal drains are considered in applying negative pore-water pressure occurred by vacuum pressure, Also, parametric studies to vacuum pressure and installation pattern of horizontal drains are carried out.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1996.06a
• /
• pp.68-68
• /
• 1996

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.355-358
• /
• 2003

This paper presents characteristics of vacuum preloaded porous air bearing. Pressure distribution of a porous pad and vacuum pocket are calculated. And load capacity and stiffness of the bearing are analyzed with various vacuum parameters, that is. clearance height. tube diameter, tube length. pumping speed of vacuum pump, vacuum pocket to porous pad area ratio. From the simulation results, optimum clearance for best performance can be selected adjusting these parameters, especially tube diameter which is the most dominant source.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.08a
• /
• pp.180-180
• /
• 2005

• Proceedings of the Korean Vacuum Society Conference
• /
• 1992.07a
• /
• pp.113-114
• /
• 1992

• Journal of Korea Foundry Society
• /
• v.25 no.4
• /
• pp.173-178
• /
• 2005

The vacuum molding process is one of the clean-foundry molding-processes that can recycle molding sands repeatedly, because molding can be accomplished by introducing vacuum only among dry molding sands in flask. The effects of molding conditions such as sand grain fineness, vacuum pressure and coating thickness on the fluidity of A356 Al alloy were studied and the results was obtained that the fluidity length was decreased as the sand grain fineness number and coating thikness were decreased and the vacuum pressure was increased. A large amount of heat removal from the molten metal resulting from the vacuum suction during the vacuum molding process was the principal cause of this decrease in fluidity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.70.1-70.1
• /
• 2015

The facility for RAON superconducting heavy-ion accelerator at a beam power of up to 400 kW will be produced rare isotopes with two electron cyclotron resonance (ECR) ion sources. Highly charged ions generated by the ECR ion source will be injected to a superconducting LINAC to accelerate them up to 200 MeV/u. During the acceleration of the heavy ions, a good vacuum system is required to avoid beam loss due to interaction with residual gases. Therefore ultra-high vacuum (UHV) is required to (i) limit beam losses, (ii) keep the radiation induced within safe levels, and (iii) prevent contamination of superconducting cavities by residual gas. In this work, a RAON vacuum design for all the accelerator system will be presented along with Monte Carlo simulation of vacuum levels in order to validate the vacuum hardware configuration, which is needed to meet the baseline requirements.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.391-396
• /
• 1999

KSTAR vacuum vessel mockup was fabricated by Korea Heavy Industries. The fabrication technology chosen for the mockup is introduced and assessed in this paper. KSTAR vacuum vessel is a huge vacuum chamber of 52 cubic meters never built in this country. Through the experiency of the KSTAR mockup fabrication, welding methods for obtaining both ultra high vacuum and structural integrity of the large vacuum chamber are extracted. The fabrication and assembly techniques for the complicated structure composed of reinforced ribs, double walls and various ports are also developed. A nondestructive test on the welding spot was performed and the results show that no major leaks violating the criterion were found. The one of the main objectives of the mockup fabrication is to measure the dimensions of the structure before and after fabrication, which plays an important role in the fabrication and the assembly. By assaying the problems occurred during mockup fabrication, the KSTAR mockup will provide the techniques for the fabrication of the main vacuum vessel.

• Applied Science and Convergence Technology
• /
• v.23 no.2
• /
• pp.97-102
• /
• 2014

A vacuum chamber for a commercial atomic force microscope (AFM) is designed and fabricated. Only minimal modifications were made to an existing microscope in an effort to work in a vacuum environment, while most of the available AFM functionalities were kept intact. The optical alignment needed for proper AFM operations including a SLD (superluminescent diode) and a photodiode can be made externally without breaking the vacuum. A vacuum level of $5{\times}10^{-3}$ torr was achieved with a mechanical pump. An enhancement of the quality factor was observed along with a shift in the resonance frequency of a non-contact-mode cantilever in a vacuum. Topographical data of a calibration sample were also obtained in air and in a low vacuum using the non-contact mode and the results were compared.