• Journal of Ocean Engineering and Technology
• /
• v.28 no.2
• /
• pp.119-125
• /
• 2014

A vertical planar motion mechanism(VPMM) test was used to increase the prediction accuracy for the maneuverability of an underwater glider model. To improve the accuracy of the linear hydrodynamic coefficients, the analysis techniques of a pure heave test and pure pitch test were developed and confirmed. In this study, the added mass and damping coefficient were measured using a VPMM test. The VPMM equipment provided pure heaving and pitching motions to the underwater glider model and acquired the forces and moments using load cells. As a result, the hydrodynamic coefficients of the underwater glider could be acquired after a Fourier analysis of the forces and moments. Finally, a motion control simulation was performed for the glider control system, and the results are presented.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.3
• /
• pp.174-180
• /
• 2011

This paper shows added mass and inertia can be acquired from the pure heaving motion and pure pitching motion respectively. A Vertical Planar Motion Mechanism (VPMM) test for the spheroid-type Unmanned Underwater Vehicle (UUV) was compared with a theoretical calculation and Computational Fluid Dynamics (CFD) analysis in this paper. The VPMM test has been carried out at a towing tank with specially manufactured equipment. The linear equations of motion on the vertical plane were considered for theoretical calculation, and CFD results were obtained by commercial CFD package. The VPMM test results show good agreement with theoretical calculations and the CFD results, so that the applicability of the VPMM equipment for an underwater vehicle can be verified with a sufficient accuracy.

• Journal of Navigation and Port Research
• /
• v.38 no.2
• /
• pp.97-103
• /
• 2014

In these days, the world has been increasing navy forces such as aircraft carriers and high-tech destroyers etc. and the importance of submarines is being emphasized. Therefore, accurate values of the derivatives in equations of motion are required to control motion of the submarines. Hydrodynamic derivatives were measured by the vertical planar motion mechanism(VPMM) model test. VPMM equipment gave pure heave and pitch motion respectively to the submarine model and the forces and moments were acquired by load cells. As a result, the hydrodynamic derivatives of the submarine are provided through the Fourier analysis of the forces and moments in this paper.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.10a
• /
• pp.117-118
• /
• 2013

In these days, the world have been increasing navy forces such as aircraft carriers and high-tech destroyers etc. and the importance of submarines is being emphasized. Therefore, accurate values of the derivatives in equations of motion are required to control motion of the submarines. Hydrodynamic coefficients were measured by the vertical planar motion mechanism(VPMM) model test. VPMM equipment gave pure heave and pitch motion respectively to the submarine model and the forces and moments were acquired by load cells. As a result, the hydrodynamic coefficients of the submarine are provided through the fourier analysis of the forces and moments in this paper.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.5
• /
• pp.287-296
• /
• 2020

The present study aims to improve the accuracy of the maneuvering simulations based on captive model test results. To derive the hydrodynamic coefficients in a self-propelled condition, a mathematical maneuvering model using a whole vehicle model was established. Captive model tests were carried out using the Vertical Planar Motion Mechanism (VPMM) equipment. A motor controller was used to control the constant propeller revolution rate during pure motion tests. The resistance tests, self-propulsion tests, static drift tests, and VPMM tests were performed in the towing tank of Seoul National University. When the vertical drift angle changes, the gravity load on the sensors were changed. The hydrodynamic forces were deduced by subtracting the gravity load from the measured forces. The hydrodynamic coefficients were calculated using the least-square method. The simulation of the turning circle test was compared with the free-running model test result, and the error of the turning radius was 8.3 % compared to the free-running model test.

• Journal of Navigation and Port Research
• /
• v.46 no.3
• /
• pp.168-178
• /
• 2022

In this study, the resistance test, the vertical static angle of the attack test and VPMM test will be conducted to estimate the maneuverability of underwater vehicles with ahead propeller. The vertical static test will be conducted within the range of -40deg to 40deg, to investigate the cross-flow drag at high incidence angles. The tests will be conducted by dividing the propeller rotation into a case in which the propeller rotates at a specific rpm, and a case in which the propeller rotates naturally, according to the towing speed. Hydrodynamic coefficients of vertical direction will be estimated by the captive model tests. Additionally, the vertical dynamic stability index based on estimated hydrodynamic coefficients will be calculated and the impact of the propeller revolution state on the index will be investigated. The results are expected to be used as reference test data for underwater vehicles with ahead propeller.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.6 s.144
• /
• pp.601-607
• /
• 2005

This paper describes a hydrodynamic modelling study based on the Feldman's equation to predict the nonlinear and coupled maneuvering characteristics of high speed submarine. The hydrodynamic coefficients set is obtained from the modeling of the cross flow drag force and sail induced vorticity, and the captive model experiments(VPMM and RA test) results used to improved the accuracy. The results contained in this paper will be helpful to predict the behavior of tight turn maneuver and to improve the SOE(Safety Operational Envelope) analysis in case of emergency maneuver.

• Journal of Navigation and Port Research
• /
• v.39 no.3
• /
• pp.173-178
• /
• 2015

In these days, the world has been increasing the development of various underwater vehicles such as ROVs (Remotely operated underwater vehicles) and AUVs (Autonomous underwater vehicles). And the importance of submarine's maneuverability is especially being emphasized. Therefore, accurate values of the derivatives in equations of motion are required to control motion of the submarines. The aims of the present study are to experimentally derive Hydrodynamic derivatives derived by the vertical planar motion mechanism (VPMM) model test, and to estimate vertical dynamic stability was estimated by using the linear hydrodynamic derivatives, the hydrodynamic derivatives of the submarine, which have a high propriety, were provided by using the fourier analysis of measured forces and moments. Furthermore it is confirmed that the experimental derivatives shows well agreement with the theoretical estimations, and the dynamic stability of the submarine was estimated as a good state, which implies that the value is greater than zero.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.269-281
• /
• 2014

This paper examines the suitability of using the Computational Fluid Dynamics (CFD) tools, ANSYS-CFX, as an initial analysis tool for predicting the drag and propulsion performance (thrust and torque) of a concept underwater vehicle design. In order to select an appropriate thruster that will achieve the required speed of the Underwater Disk Robot (UDR), the ANSYS-CFX tools were used to predict the drag force of the UDR. Vertical Planar Motion Mechanism (VPMM) test simulations (i.e. pure heaving and pure pitching motion) by CFD motion analysis were carried out with the CFD software. The CFD results reveal the distribution of hydrodynamic values (velocity, pressure, etc.) of the UDR for these motion studies. Finally, CFD bollard pull test simulations were performed and compared with the experimental bollard pull test results conducted in a model basin. The experimental results confirm the suitability of using the ANSYS-CFX tools for predicting the behavior of concept vehicles early on in their design process.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.1
• /
• pp.27-31
• /
• 2011

The previously developed method of estimating the propulsion performance of a UUV was applied to the high speed UUV, which is propelled by commercial thrusters. The thrusters were selected with an overdesign mentality; in other words, their capacities were excessive. At that point, the designer's concern was focused on a question regarding at what rpm the UUV could reach the design speed. Because the developed method required thrust coefficient curve data, the researchers asked for the POW data of the thrusters from the manufacturer. From the data, the researchers extracted the thrust coefficient and estimated the rpm value of design speed for the UUV. Finally, the researchers compared the estimated value and the result from a self-propulsion test using a VPMM (Vertical planar motion mechanism) test at a towing tank in MOERI.