• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.369-375
• /
• 1997

$V_{2}O_{5}/ThO_{2}/Pd$-doped $SnO_{2}$ sensor has a good selectivity and stability to CO at high sensor temperature of about $500^{\circ}C$, and shows rapid response. In particular, many kinds of interference gases, such as $NO_{x}$, $C_{3}H_{8}$, $CH_{4}$ and $SO_{2}$ have been found to give only a slight influence on the sensor selectivity to CO gas sensitivity by doped $V_{2}O_{5}$ (3.0 wt.%). For the sensor we used well-known thick film technological route with $V_{2}O_{5}$(3.0 wt.%), Pd(1.0 wt.%) and $ThO_{2}$(l.5 wt.%) as catalytic materials. In the case of mixed $NO_{x}$-CO gases, as combustion exhaust gas, only CO detection by $SnO_{2}$ type semiconductor sensor is generally very difficult because of $NO_{x}$ interference. The developed sensors can use to measure the exhausting gas of the automobile or the boiler for the Air-to-Fuel ratio control.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.552-558
• /
• 2000

LiMn2O4 thin fiolm cathodes for Li-ion secondary battery were fabricated by r.f. magnetron sputtering technique. As-deposited films were amorphous. A spinel structure could not be obtained LiMn2O4 films by in-situ thermal annealing. After post thermal annealing over $700^{\circ}C$ in oxygen atmosphere, LiMn2O4 films prepared above 100 W r.f. power could be crystallized into a spinel structure. The electrochemical property of the LiMn2O4 film cathodes was tested in a Li/1 M LiClO4 in PC/LiMn2O4 cell. From cyclic voltammetry at scan rate of 2mV/sec of 2.5~4.5V, LiMn2O4 electrode prepared by post annealing at 75$0^{\circ}C$ showed good initial capacity. LiMn2O4 electrode prepared by post annealing at 80$0^{\circ}C$ showed the best crycling performance.

• Korean Journal of Soil Science and Fertilizer
• /
• v.46 no.3
• /
• pp.163-172
• /
• 2013

The aquatic insect collected at six areas (each 2 for mountain area, plain field, and urban area) from 2009 to 2011 were classified to analyze the distribution and diversity of species. Frequency (number of aquatic insect: N), number of species (S), similarity index (C), richness index (R1, R2), variety index (V1, V2), evenness index (E1, E2, E3, E4, E5), and dominance index (D1) were investigated. Total N and S were 143 and 84, respectively. C matrix of 153 combinations was constructed with the average of 0.542. The average C of 3 years (0.659) was 9.9% P, more higher than the average C of 6 areas (0.560). The average values of the index of 18 plots were 2.28, 0.17, 1.24, 1.08, 0.07, 0.06, 0.01, 0.87, 0.31, 0.93 for R1, R2, V1, V2, E1, E2, E3, E4, E5, D1, respectively. The order in the coefficient of variation (CV) of the indicator for 18 plots was N (70.0%) > E3 (54.9%) > E1 (49.6%) > R2 (40.5%) > S (35.3%) > R1 (33.7%) > E2 (28.4%) > E5 (15.9%) > V1 (11.1%) > E4 (6.3%) > V2 (5.1%) > D1 (4.8%). The correlation matrix with 66 combinations between the indexes was constructed with statistical significance for 33 combinations. However, R1, V1, E2 and D1 were the proper indexes to represent species diversity of aquatic insect based on the correlation matrix and the theory of statistical independence. The richness index was highest in mountain, variety index in urban area, and evenness index in plain field. However, the dominance index was lowest in urban area.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.2
• /
• pp.165-171
• /
• 2013

WAVE(Wireless Access in Vehicular Environments) is a representative V2V communication protocol and its standards of MAC and PHY parts except for security were published. In order to control traffic flow and ensure driver's safety using V2V communication, various projects are conducting. In particular, safety application has been researched. Therefore, in this paper, we designed the safety application algorithm, which informs a driver of the dangerous status when driver tries to turn left in an intersection and we also implemented the algorithm. Proposed algorithm configures a model for a host vehicle and a vehicle coming in opposite lane and in case that there is collision hazard it provides warning message to driver by using HMI. In order to evaluate the proposed algorithm's performance, we configured the test bed using test vehicles and we tested the algorithm on proving ground with the composed test scenarios. As test results, our system showed excellent performance. If the infrastructures for V2I communications are constructed, we will optimize our system more precisely and stably.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.6
• /
• pp.229-235
• /
• 2002

This paper presents the fabrication of polycrystalline thin film transistor(TFT) using sequential lateral solidification(SLS) of amorphous silicon. The fabricated SLS TFT showed high Performance suitable for active matrix liquid crystal display(AMLCD). The SLS process involves (1) a complete melting of selected area via irradiation through a patterned mask, and (2) a precisely controlled pulse translation of the sample with respect to the mask over a distance shorter than the super lateral growth(SLG) distance so that lateral growth extended over a number of iterative steps. The SLS experiment was performed with 550$\AA$ a-Si using 308nm XeCl laser having $2\mu\textrm{m}$ width. Irradiated laser energy density is 310mJ/$\textrm{cm}^2$ and pulse duration time was 25ns. The translation distance was 0.6$\mu$m/pulse, 0.8$\mu$m/pulse respectively. As a result, a directly solidified grain was obtained. Thin film transistors (TFTs) were fabricated on the poly-Si film made by SLS process. The characteristics of fabricated SLS p -type poly-Si TFT device with 2$\mu\textrm{m}$ channel width and 2$\mu\textrm{m}$ channel length showed the mobility of 115.5$\textrm{cm}^2$/V.s, the threshold voltage of -1.78V, subthreshold slope of 0.29V/dec, $I_{off}$ current of 7$\times$10$^{-l4}$A at $V_{DS}$ =-0.1V and $I_{on}$ / $I_{off}$ ratio of 2.4$\times$10$^{7}$ at $V_{DS}$ =-0.1V. As a result, SLS TFT showed superior characteristics to conventional poly-Si TFTs with identical geometry.y.y.y.

• Journal of Microbiology and Biotechnology
• /
• v.17 no.11
• /
• pp.1751-1757
• /
• 2007

Elastin-like polypeptides (ELPs) undergo a reversible inverse phase transition upon a change in temperature. This thermally triggered phase transition allows for a simple and rapid means of purifying a fusion protein. Recovery of ELPs-tagged fusion protein was easily achieved by aggregation, triggered either by raising temperature or by adding salt. In this study, levansucrase has been used as a model enzyme in the development of a simple one-step purification method using ELPs. The levansucrase gene cloned from Pseudomonas aurantiaca S-4380 was tagged with various sizes of ELPs to functionally express and optimize the purification of levansucrase. One of two ELPs, ELP[V-20] or ELP[V-40], was fused at the C-terminus of the levansucrase gene. A levansucrase-ELP fusion protein was expressed in Escherichia coli $DH5{\alpha}$ at $37^{\circ}C$ for 18 h. The molecular masses of levansucrase-ELP[V-20] and levansucrase-ELP[V-40] were determined as 56 kDa and 65 kDa, respectively. The phase transition of levansucrase-ELP[V-20] occurred at $20^{\circ}C$ in 50 mM Tris-Cl (pH 8) buffer with 3 M NaCl added, whereas the phase transition temperature ($T_t$) of levansucrase-ELP[V-40] was $17^{\circ}C$ with 2 M NaCl. Levansucrase was successfully purified using the phase transition characteristics of ELPs, with a recovery yield of higher than 80%, as verified by SDS-PAGE. The specific activity was measured spectrophotometrically to be 173 U/mg and 171 U/mg for levansucrase-ELP[V-20] and levansucrase-ELP[V-40], respectively, implying that the ELP-tagging system provides an efficient one-step separation method for protein purification.

• Journal of Hydrogen and New Energy
• /
• v.24 no.5
• /
• pp.367-372
• /
• 2013

Hydrogen storage as a metal hydride is the most promising alternative because of its relatively large hydrogen storage capacities near room temperature. TiMn2-based C14 Laves phases alloys are one of the promising hydrogen storage materials with easy activation, good hydriding-dehydriding kinetics, high hydrogen storage capacity and relatively low cost. In this work, multi-component, hyper-stoichiometric $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ C14 Laves phase alloys were prepared by a vacuum induction melting for a hydrogen storage tank. Since pure vanadium (V) is quite expensive, the substitution of the V element in these alloys has been tried and some interesting results were achieved by replacing V by commercial ferrovanadium (FeV) raw material. In addition, the melt-spinning process, which was applied to the manufacturing of some of these alloys, could make the plateau slopes much flatter, which resulted in the increase of reversible hydrogen storage capacity. The improvement of sloping properties of melt-spun $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ alloys was mainly attributed to the homogeneity of chemical composition.

• Journal of Hydrogen and New Energy
• /
• v.10 no.1
• /
• pp.59-69
• /
• 1999

AlN thin films were fabricated by reactive sputtering for the application of MIS devices with Al/AlN/Si structure. It has investigated the surface morphology change, I-V characteristics, C-V characteristics, and chemical composition of AlN films with the intriducing time of hydrogen on the fixed deposition condition(RF power: 150W, sputtering pressure: 5mTorr, flow rate ratio of $Ar/N_2=1$, hydrogen concentration: 5%). By addition of the hydrogen the deposition rate decreased drastically whereas the surface morphology changed little. It has been found from the analysis of I-V and C-V characteristics curves that the films deposited with hydrogen addition in initial stage had lower leakage current density, lower flat band voltage and hystersis profile when compared with those with hydrogen addition in last stage. The oxygen concentration in AlN films decreased with addition of hydrogen gas, which suggesting a profitable role in the insulation and C-V characteristics of AlN films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.57-58
• /
• 2011

III-V족 화합물 반도체의 일종인 InSb는 77 K에서 0.23 eV의 작은 밴드 갭을 가지며 높은 전하 이동도를 가지고 있기 때문에 대기권에서 전자파 흡수가 일어나지 않는 3~5 ${\mu}m$범위의 장파장 적외선 감지가 가능하여 중적외선 감지 소자로 이용되고 있다. 하지만 InSb는 밴드 갭이 매우 작기 때문에, 소자 제작시 누설전류에 의한 소자 특성의 저하가 문제시 되고 있다. 또한 다른 화합물 반도체에 비해 녹는점이 낮고, 휘발성이 강한 5족 원소인 Sb의 승화로 기판의 화학양론적 조성비(stoichiometry)가 변하기 쉬워, 계면특성 저하의 원인이 된다. 따라서 우수한 특성을 가지는 적외선 소자의 구현을 위해서, 저온에서 계면 특성이 우수한 고품질의 절연막 증착 연구가 필수적이다. 본 연구에서는 InSb 기판 위에 $SiO_2$, $Si_3N_4$의 절연막 형성시 증착온도의 변화에 따른 계면 트랩 밀도를 분석하였다. $SiO_2$, $Si_3N_4$ 절연막은 플라즈마 화학 기상 증착법(PECVD)을 이용하여 n형 InSb 기판 위에 증착하였으며, 증착온도를 $120^{\circ}C$부터 $240^{\circ}C$까지 변화시켰다. Metal oxide semiconductor(MOS) 구조 제작을 통하여, 커패시턴스-전압(C-V)분석을 진행하였으며, 절연막과 InSb 사이의 계면 트랩 밀도를 Terman method를 이용하여 계산하였다[1]. 또한, $SiO_2$와 $Si_3N_4$의 XPS 분석과 TOF-SIMS 분석을 통하여 계면 트랩 밀도의 원인을 밝혀 보았다. $120{\sim}240^{\circ}C$ 온도 범위에서 계면 트랩 밀도는 $Si_3N_4$의 경우 $2.4{\sim}4.9{\times}10^{12}cm^{-2}eV^{-1}$, $SiO_2$의 경우 $7.1{\sim}7.3{\times}10^{11}cm^{-2}eV^{-1}$ 값을 나타냈고, 두 절연막 모두 증착 온도가 증가할수록 계면 트랩 밀도가 증가하는 경향을 보였다. 그러나 모든 샘플에서 $Si_3N_4$의 경우, flat band voltage가 음의 전압으로 이동한 반면, $SiO_2$의 경우, 양의 전압으로 이동하는 것을 확인할 수 있었다. 계면 트랩 밀도 증가의 원인을 확인하기 위해서, oxide를 $120^{\circ}C$, $240^{\circ}C$에서 증착시킨 샘플을 XPS 분석을 통하여 깊이에 따른 성분분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 계면에서 $In_2O_3$와 $Sb_2O_3$ 피크의 증가를 확인하였다. 이는 계면에서 oxide양이 증가함을 의미하며, 이렇게 생성된 oxide는 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. Nitride 절연막을 증착시킨 샘플은 TOF-SIMS 분석을 통해, 계면에서의 성분 분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 In-N, Sb-N, Si-N 결합의 감소를 확인하였다. 이렇게 분해된 결합들의 dangling 결합이 늘어 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. 최종적으로, 소자특성을 확인 하기 위하여 계면 트랩 밀도가 가장 낮게 측정된 $200^{\circ}C$ 조건에서 $SiO_2$ 절연막을 증착하여 InSb 적외선 소자를 제작하였다. 전류-전압(I-V) 분석 결과 -0.1 V에서 16 nA의 누설 전류 값을 보였으며, $2.6{\times}10^3{\Omega}cm^2$의 RoA(zero bias resistance area)를 얻을 수 있었다. 절연막 증착조건의 최적화를 통하여, InSb 적외선 소자의 특성이 개선됨을 확인할 수 있었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.286-291
• /
• 2006

We studied possibility of mixing treatment of livestock wastewater and sewage using Phanerochaete chrysosporium PSBL-1. Our study showed that 97.6% of SS and 95% of T-P removal efficiency was achieved when 2 mL BF02(a coagulant) and 100 mL C-210EL(a cationic polymer) were added to the mixture(2:1, v/v) of livestock wastewater and sewage. We studied treatment characteristic of Phanerochaete chrysosporium PSBL-1, after were mixed pretreated wastewater and sewage by dillution ten times about livestock wastewater. The removal efficiency of NBDCOD(non-biodegradable COD), $NH_3-N$ and T-N was increased according to increase of pH. That is, T-N concentration of effluent was satisfied 60 mg/L by drain water waterqulity standard of livestock wastewater public treatment facilities with 35 mg/L from a lapse of five days at pH 6.7, 51 mg/L from a lapse of three days at pH 8 and 33 mg/L from a lapse of one day at pH 10. Moreover $COD_{Mn}$ concentration of effluent was satisfied 40 mg/L by drain water waterqulity standard of livestock wastewater public treatment facilities after a laps of one day at all pH. Organics and nitrogen concentrations of effluent were higher case with addition of V.A.(veratryl alcohol) than case without addition of V.A.(veratryl alcohol). $COD_{Mn}$ concentration of effluent satisfied drain water qulity standard of livestock wastewater public treatment facilities from a lapse of one day, when C/N rate(3:1) of influent was not controled. T-N satisfied that from a lapse of two days, when C/N rate was controled with $4{\sim}6$.