• Journal of the Korean Vacuum Society
• /
• v.14 no.2
• /
• pp.78-83
• /
• 2005

Nanometric crystalline silicon (no-Si) embedded in dielectric medium has been paid attention as an efficient light emitting center for more than a decade. In nc-Si, excitonic electron-hole pairs are considered to attribute to radiative recombination. However the surface defects surrounding no-Si is one of non-radiative decay paths competing with the radiative band edge transition, ultimately which makes the emission efficiency of no-Si very poor. In order to passivate those defects - dangling bonds in the $Si:SiO_2$ interface, hydrogen is usually utilized. The luminescence yield from no-Si is dramatically enhanced by defect termination. However due to relatively high mobility of hydrogen in a matrix, hydrogen-terminated no-Si may no longer sustain the enhancement effect on subsequent thermal processes. Therefore instead of easily reversible hydrogen, phosphorus was introduced by ion implantation, expecting to have the same enhancement effect and to be more resistive against succeeding thermal treatments. Samples were Prepared by 400 keV Si implantation with doses of $1\times10^{17}\;Si/cm^2$ and by multi-energy Phosphorus implantation to make relatively uniform phosphorus concentration in the region where implanted Si ions are distributed. Crystalline silicon was precipitated by annealing at $1,100^{\circ}C$ for 2 hours in Ar environment and subsequent annealing were performed for an hour in Ar at a few temperature stages up to $1,000^{\circ}C$ to show improved thermal resistance. Experimental data such as enhancement effect of PL yield, decay time, peak shift for the phosphorus implanted nc-Si are shown, and the possible mechanisms are discussed as well.

• Reproductive and Developmental Biology
• /
• v.30 no.1
• /
• pp.65-70
• /
• 2006

This study investigated apoptosis and in vitro development of parthenogenetic preimplantation porcine embryos. In vitro matured oocytes for $42{\sim}44h$ were used. Apoptotic cell death was analyzed by using a terminal deoxynucleatidyl transferase mediated deoxyuridine 5-triphosphate nick-end tabling (TUNEL) assay. In experiment 1, oocytes were activated with two electric pulses (CH) of 1.2 kV/cm for $30{\mu}sec$ (E), E + 6-dimethylaminopurine (6-DMAP) or E + cycloheximide (CH) and cultured in PZM-3 under 5% $CO_2$ in air at $38.5^{\circ}C$. In experiment 2, oocytes were activated by E and cultured in PZM-3 or NCSU-23 under a gas atmosphere of 20% $O_2$ ($5%\;CO_2$, in air) or 5% $O_2$ $(5%\;CO_2,\;5%\;O_2\;90%\;N_2)\;at\;38.5^{\circ}C$. Oocytes activated with E+6-DMAP or E+CH showed higher blastocyst rates (36.3% and 32.5%) compared to E alone (27.7%). The frequency of apoptosis according to treatments were 5.3%, 7.7% and 7.1% respectively. Oocytes activated with E alone showed lower (P<0.05) frequency of apoptosis compared to other groups. In experiment 2, parthenotes cultured in PZM-3 showed slightly higher blastocyte rates (28.2% and 29.7%) compared to NCSU-23 (22.6% and 24.4%) regardless of atmosphere. Blastocysts generated in PZM-3 showed lower (P<0.05) apoptosis rate under 20% $O_2$ (9.2% vs 16.9%), whereas those in NCSU-23 had slightly lower apoptosis rate under 5% $O_2$ (14.0% vs 18.4%). This result represents that activation method and culture condition could affect the frequency of apoptosis as well as in vitro developmental rate.

• The Korean Journal of Pharmacology
• /
• v.25 no.1
• /
• pp.1-11
• /
• 1989

In this study, it was aimed to investigate the role of serotonergic neurotransmission in nucleus tractus solitarius (NTS) for the central regulation of blood pressure and heart rate and its involvement in baroreceptor reflex activation in rats. A microinjection of 5-hydroxytryptamine (5-HT) into the NTS produced decreases in blood pressure and heart rate. Maximal decreases were $34.4{\pm}1.6$ mmHg and $41.7{\pm}10.2$ beats per min by 300 pmol of 5-HT. Microinjections of ${\alpha}-methylnor-adrenaline$ $({\alpha}-MNE)$ and clonidine manifested similar decreases in blood pressure and heart rate. The hypotensive and bradycardial effects of 5-HT were blocked by previous applications of 5-HT antagonists, ritanserin, methysergide and ketanserin into the NTS, respectively. By pretreatment with reserpine and 6-hydroxydopamine (6-OHDA, i.c.v.), both hypotensive and bradycardial effects of 5-HT were significantly attenuated. Pretreatment with 5, 7-dihydroxytryptamine (5,7-DHT, i.c.v.) enhanced the hypotensive and bradycardial effects of 5-HT. Similarly, following pretreatment with 6-OHDA, the effects of clonidine were increased. Pretreatment either with 5,7-DHT or 6-OHDA significantly attenuated the sensitivity of baroreflex produced either by phenylephrine or by sodium nitroprusside. When either 5,7-DHT or 6-OHDA was injected into the NTS $(5,7-DHT;\;8{\mu}g\;6-OHDA;\;10{\mu}g)$, both of the baroreflex sensitivities were impaired. In the immunohistochemical study, the injection of 6-OHDA into the the NTS led to reduction of axon terminal varicosity, however, the injection did not reduce the numbers of catecholaminergic cell bodies. Likewise, when 5,7-DHT was injected into the NTS, the varicosity of serotonergic axon terminals was markedly reduced. Based on these results, it is suggested that (1) stimulation of serotonergic receptors in the NTS leads to decreases in blood pressure and heart rate as observed with the stimulation of catecholaminergic system, (2) both serotonergic and catecholaminergic receptors may be located postsynaptically, and (3) the serotonergic neurons as well as catecholaminergic neurons may have a close relevance for the activation of baroreflex.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1635-1641
• /
• 1999

Bacillus subtilis PCA20-3 was isolated from meju and was found to produce a protease. The strain produced the maximum amount of enzyme in the medium containing soytone (0.2%), soluble starch (2%), $(NH_4)_2SO_4\;(0.1%),\;CaCl_2(0.1%),\;yeast\;extract\;(0.01%),\;K_2HPO_4\;(0.1%),\;and\;KH_2PO_4\;(0.1%)$. Protease was first concentrated by ammonium sulfate (80% saturation, w/v) precipitation of culture supernatant. Then the enzyme was purified by column chromatography using CM Sephadex C-50. The collected proteins were rechromatographed using Sephadex G-100 gel filtration column. The fraction with protease active from Sephadex G-100 gel chromatography was found to be pure when examined by SDS-polyacrylamide gel electrophoresis and YMC-pak reverse phase chromatography. Specific activity, yield and purity were 76 U/mg. 2.7%, and 7.6 fold, respectively. The molecular weight of the enzyme was estimated to be 31.5 kDa by SDS-PAGE. The number of amino acids calculated from molecular weight was evaluated about 321 residues. N-terminal sequence of the enzyme was $Val^1-Pro^2-Tyr^3-Gly^4-Val^5-Ser^6-Gln^7-Gly^8-Lys^9-Ala^{10}$.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.4
• /
• pp.429-439
• /
• 1999

Potentiometric titration data were collected for some humic acids purified from Korean upland and paddy soils over a range of pH (3.0 - 11.0) with $NaNO_3$ background electrolyte concentrations (0.01, 0.10, 0.50 and 1.00 M). The data were applied to model A and V which included both intrinsic heterogeneity of humic materials and electrostatic interaction influences on binding sites. The elemental analysis were conducted for various type of humic samples. The $E_4/E_6$ ratio proposed negative correlation with the total carboxyl groups ($r^2$= 0.9988). The charge ($cmol_c\;kg^{-1}$) on the humic acids became more negative as the ionic strength increased. In both continuous and batch titrations, the ionic strength effect was greater in Namweon series (pH 6.39) than others at pH 5.00. The effect of ionic strength on surface charge appears to be greater in batch titrations. This could suggest that continuous titrations do not represent an equilibrium state and the effects of electrolyte concentration was not fully realized during the course of titrations. Both models described experimental data obtained from continuous and batch titrations well over a range of ionic strengths. Model A is more simpler than model V but adaptes more fitted parameters. Thus, the observed change in apparent binding constants with surface charge is regarded solely due to electrostatic influences rather than functional group heterogeneity. However, Model V is more mechanistically realistic in a number of discrete ligand binding sites.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.447-451
• /
• 2007

We investigated the dependence of the various annealing conditions and thickness ($6\sim45nm$) of the Ti-doped $Al_2O_3$ coating on the electrochemical properties and the capacity fading of Ti-doped $Al_2O_3$ coated $LiCoO_2$ films. The Ti-doped-$Al_2O_3$-coating layer and the cathode films were deposited on $Al_2O_3$ plate substrates by RF-magnetron sputter. Microstructural and electrochemical properties of Ti-doped-$Al_2O_3$-coated $LiCoO_2$ films were investigated by transmission electron microscopy (TEM) and a dc four-point probe method, respectively. The cycling performance of Ti-doped $Al_2O_3$ coated $LiCoO_2$ film was improved at higher cut-off voltage. But it has different electrochemical properties with various annealing conditions. They were related on the microstructure, surface morphology and the interface condition. Suppression of Li-ion migration is dominant at the coating thickness >24.nm during charge/discharge processes. It is due to the electrochemically passive nature of the Ti-doped $Al_2O_3$ films. The sample be made up of Ti-doped $Al_2O_3$ coated on annealed $LiCoO_2$ film with additional annealing at $400^{\circ}C$ had good adhesion between coating layer and cathode films. This sample showed the best capacity retention of $\sim92%$ with a charge cut off of 4.5 V after 50 cycles. The Ti-doped $Al_2O_3$ film was an amorphous phase and it has a higher electrical conductivity than that of the $Al_2O_3$ film. Therefore, the Ti-doped $Al_2O_3$ coated improved the cycle performance and the capacity retention at high voltage (4.5 V) of $LiCoO_2$ films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.310-310
• /
• 2014

ZnO박막은 넓은 밴드갭 (3.37 eV), 높은 여기 결합 에너지 (60 meV)를 가지는 육방정계 우르자이트(hexagonal wurtzite) 결정구조를 가지는 II-VI족 화합물 반도체로, 가시광선 영역에서의 높은 광학적 투과도 특성과 자외선 파장에서 발광이 가능한 장점을 가진다. 최근, ZnO박막 성장 기술이 상당히 발전하였지만, 아직까지도 p-형 ZnO박막 성장 기술은 충분히 발전하지 못하여 ZnO의 동종접합 LED는 아직 상용화되지 않고 있는 실정이다. 따라서, 많은 연구 그룹에서 p-GaN, p-SiC, p-diamond, p-Si 등과 같은 p-type 물질 위에 n-type ZnO를 성장시킨 이종접합 다이오드가 연구되고 있다. 특히, p-GaN의 경우 ZnO와의 격자 불일치 정도가 1.8 % 정도로 작다는 장점이 있어 많은 연구가 이루어 지고 있다. 일반적으로 c-축을 기반으로 한 극성ZnO 발광다이오드에서는 자발 분극과 압전 분극 현상에 의해 밴드 휨 현상이 발생하고, 이로 인해 전자와 정공의 공간적 분리가 발생하게 되어 발광 재결합 효율이 제한되고 있다는 문제가 발생한다. 따라서, 본 연구에서는 극성 (0001) 및 비극성 (10-10) n-ZnO/p-GaN 발광다이오드의 성장 및 발광 소자의 전기 및 광학적 특성에 대한 비교 연구를 진행하였다. 금속유기 화학증착법을 이용하여 c-면과 m-면 위에 각각 극성 (0001) 및 반극성 (11-22) GaN박막을 $2.0{\mu}m$ 성장시킨 후 Mg 도핑을 한 p-GaN을 $0.4{\mu}m$ 성장시켜 각각 극성 (0001) 및 반극성 (11-22) p-GaN템플릿을 준비하였다. 이후, N2분위기 $700^{\circ}C$에서 3분동안 열처리를 통하여 Mg 도펀트를 활성화시킨 후 원자층 증착법을 이용하여 동시에 극성 및 반극성 p-GaN의 위에 n-ZnO를 $0.11{\mu}m$ 성장시켜 이종접합구조의 발광소자를 형성하였다. 이때, 극성 (0001) p-GaN 위에는 극성의 n-ZnO 박막이 성장되는 반면, 반극성 (11-22) p-GaN 위에는 비극성 (10-10) n-ZnO 박막이 성장됨을 HR-XRD로 확인하였다. 극성 (0001) n-ZnO/p-GaN이종접합 발광다이오드의 전계 발광 스펙트럼에서는 430 nm 와 550 nm의 두 피크가 동시에 관찰되었다. 430 nm 대역의 파장은 p-GaN의 깊은 준위에서 발광하는 것으로 판단되며, 550 nm 피크 영역은 ZnO의 깊은 준위에서 발광되는 것으로 판단된다. 특히, 10 mA 이하의 저전류 주입시 550 nm의 피크는 430 nm 영역보다 더 큰 발광세기를 나타내고 있다. 하지만, 10 mA 이상의 전류주입 하에서는 550 nm의 영역보다 430 nm의 발광세기가 더욱 증가하는 것을 확인할 수 있었다. 이것은 ZnO의 밴드갭이 3.37 eV로 GaN의 밴드갭인 3.4 eV다 작기 때문에 우선적으로 ZnO의 깊은 준위에서 발광하는 550 nm가 더욱 우세하지만, 지속적으로 전류주입 증가에 따른 캐리어 증가시 n-ZnO에서 p-GaN로 전자가 넘어가며 p-GaN의 깊은 준위인 430 nm에서의 피크가 우세해지는 것으로 판단된다. 반면에, 비극성 (10-10) n-ZnO/반극성 (11-22) p-GaN 구조의 이종접합 발광다이오드로 전계 발광 스펙트럼에서는 극성 (0001) n-ZnO/p-GaN에 비하여 매우 낮은 전계 발광 세기를 나타내고 있다. 이는, 극성 n-ZnO/p-GaN에 비하여 비극성 n-ZnO/반극성 p-GaN의 결정성이 상대적으로 낮기 때문으로 판단된다. 또한, 20 mA 영역에서도 510 nm의 깊은 준위와 430 nm의 발광이 관찰되었다. 동일한 20 mA하에서 두 피크의 발광세기를 비교하면 430 nm의 영역은 극성 n-ZnO/p-GaN에 비하여 매우 낮은 값을 나타내고 있다. 이는 반극성 (11-22) p-GaN의 경우 극성 (0001) p-GaN에 비하여 우수한 p-형 특성에 기인한 것으로 판단된다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.664-669
• /
• 2012

Nano-structured one-dimensional $Na_2Ti_6O_{13}$ particles were synthesized by a molten salt process. Effects of processing parameters on the microstructure and band gap energy of the $Na_2Ti_6O_{13}$ powder were studied in this paper. For the synthesis of the $Na_2Ti_6O_{13}$ particles, two different raw materials of tubular shaped Na-titanate (Na-TiNT) and spherical shaped $TiO_2$ were utilized. Synthesizing with the raw material of Na-TiNT, around 70nm thick 1D-$Na_2Ti_6O_{13}$ with the bandgap energy of 3.5 eV was obtained at $810^{\circ}C$. Below $810^{\circ}C$ or without the presence of NaCl, 1D-$Na_2Ti_6O_{13}$ was in a relatively short in length and agglomerated state. With the processing temperature increased, the thickness of the 1D-$Na_2Ti_6O_{13}$ was also observed to be increased. On the other hand, when $TiO_2$ was employed as a raw material, the mixed amount of $Na_2CO_3$ played an important role in transforming the morphology and phase of the raw material, affecting the bandgap energy of the synthesized product. Specific surface area of the synthesized 1D-$Na_2Ti_6O_{13}$ was significantly affected by the raw and mixed materials as well as processing temperature. When Na-TiNT was processed at $810^{\circ}C$ with NaCl, the specific surface area of the 1D-$Na_2Ti_6O_{13}$ showed the best value of 30.63 $m^2/g$.

• Applied Biological Chemistry
• /
• v.39 no.2
• /
• pp.118-122
• /
• 1996

The main objectives of this study was to characterize physicochemical properties, oxidative stability and sensory property of perilla oil obtained by various roasting temperature and time. Roasting temperature of perilla seed was conducted from $150^{\circ}C\;to\;210^{\circ}C$ at the increment of $20^{\circ}C$, and roasting time was 10, 20 and 30 min. Yield of perilla oil was increased as the roasting temperature and time were increased. The content of linolenic acid, a major fatty acid in perilla oil, was 60%. There was no differences in fatty acid composition upon the roasting conditions. Unsaturated fatty acid was contained more than 88% of the total fatty acids. Contents of phosphorus in perilla oils were decreased as the roasting temperature and time were increased. Phosphorus contents were significantly decreased at $190^{\circ}C$ for 30 min and $210^{\circ}C\;for\;20{\sim}30$ min. Tocopherol contents were unchanged at the roasting conditions of present study and gamma-tocopherol was shown to be the major tocopherol. Sensory evaluation of perilla oil roasted in various conditions showed significant differences in taste, color, flavor and palatability. The perilla oil roasted at $190^{\circ}C$ for 20 min had the best palatability.

• Food Science and Preservation
• /
• v.19 no.6
• /
• pp.849-857
• /
• 2012

This study was conducted to determine the effects of the pretreatment and infrared drying methods on the physicochemical properties and antioxidant activities of dried peaches. The pretreatment methods were the 30 min treatment of NaCl, vitamin C, and soluble Ca (1:5 w/v immersion ratio), and leaving them untreated before infrared drying at $55^{\circ}C$ for 20 hr. The moisture content was lower in the pre-treated group and was significantly lowest in the 0.3% NaCl. The titratable acidity and soluble solid content and acid ratio (SS/TA) were high for the vitamin C and soluble Ca groups. The browning degree and cutting strength of the dried peach were lower in the pre-treated group. The total sugar content in the 0.3% NaCl group was significantly higher than those in the vitamin C and soluble Ca groups. The Ca contents were more effective in the soluble Ca treated group and increased with higher Ca concentration. The sensory evaluation results indicated that the organoleptic scores for the overall preference were higher in the 0.1% vitamin C treated group. The phenolic compounds and ABTS radical scavenging ability were high for the 0.1% vitamin C and 0.1% soluble Ca treated groups. These results suggest that pretreatment affected the qualities of the dried peaches, showing that infrared drying can be applied to the production of high quality dried peach products.