• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.131-131
• /
• 2017

알루미늄은 내식성, 내마모성과 같은 물리적, 화학적 성질이 우수하지 못하여 이를 향상시키기 위해서 양극산화법이 산업적으로 널리 사용되고 있다. 알루미늄 양극산화법을 적용하면 강도, 내마모성 및 내식성이 향상될 뿐만 아니라 알루미늄 표면에 규칙적으로 배열된 30nm~100nm 크기의 pore에 염료를 흡착시켜 다양한 색상의 외관을 가지는 양극산화피막을 형성시킬 수 있다. Pore간의 간격은 수십nm~수백nm 정도이며, pore의 크기와 간격 및 깊이는 양극산화조건(양극산화 전압, 전해액의 종류와 농도 및 온도)에 의해 크게 변화된다. 또한 염료의 농도와 착색 시간에 따라서 양극산화 피막의 색조가 변화되는 것으로 알려져 있다. 따라서 본 연구에서는 양극산화피막의 색조에 미치는 전해조건의 영향을 조사하고, 분광측색계를 사용하여 산화피막의 색조를 정량적으로 분석하고 또한 산화피막의 pore에 흡착된 염료를 정량분석하기 위해서 UV-visible을 사용하여 분석하였다. Al5052 합금을 이용하여 에칭, 양극산화, 착색처리, 봉공(sealing)처리를 실시하였다. $55^{\circ}C$ 100g/L NaOH 용액에서 에칭을, $25^{\circ}C$ 10 vol.% $HNO_3$ 용액에서 디스머트를 실시한 다음, $25^{\circ}C$ 10 vol.% $H_2(SO_4)$ 용액에서 15V의 정전압으로 양극산화를 실시하였다. 이후, $55^{\circ}C$ 5~8g/L의 오렌지, 블랙 착색염료(일본 OKUNO 사(社)의 TAC-LH(301), TAC-BLH(411))를 사용하여 착색처리를, $85^{\circ}C$ 초산니켈 수용액에서 봉공처리를 실시하였다. 착색조건으로는 양극산화 시간(5분, 10분, 15분, 20분), 착색 시간(15초, 1분, 2분, 5분) 및 착색 농도(오렌지 -2.5g/L, 5g/L, 7.5g/L, 블랙 - 4g/L, 8g/L, 12g/L)를 변화시켰으며, 산화피막의 색조를 정량 분석하기 위해 분광측색계를 사용하였고 흡착된 염료의 농도를 정량 분석하기 위해서 $55^{\circ}C$, 1M NaOH에 재용해하여 UV-visible로 흡광도를 측정하였다. 양극산화피막의 색조는 양극산화 시간이 길어질수록, 착색시간이 길어질수록, 착색농도가 진할수록 산화피막에 흡착되는 염료의 양이 증가하며 색조가 더 선명해지고 진해지는 것을 확인하였다. 이를 분광측색계로 분석하였을 때 각 전해조건하에서 경향성을 나타내었다. 또한 흡광도 측정을 통해 계산한 염료의 양과 전해조건의 상관관계를 조사하였다. 양극산화 시간이 길어지면 산화피막의 두께가 증가하여 염료가 흡착될 수 있는 표면적이 넓어지고, 착색 시간이 길어지면 동일한 산화피막에 더 많은 염료가 흡착이 된다. 그리고 착색 농도가 진할수록 동일면적, 동일시간 하에서 더 많은 염료가 흡착되어 결과적으로 전해조건이 강해질수록 산화피막의 색조가 진해지는 것으로 판단된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.39.2-39.2
• /
• 2011

The new and renewable energy today has a great interest in all countries around the world. In special it has need more limit of the fossil fuel that needs of low carbon emission among the social necessary conditions. Recently, the high-rise building demand the structural safety, the economic feasibility and the functional design. The high-rise building spends enormous energy and it satisfied the design in solving energy requirements. The requirements of energy for the building depends on the partly form wind energy due to the cladding of the building that came from the surroundings of the high-rise building. In this study of the wind energy, the cladding of the building was assessed a tentative study. The wind energy obtains from several small wind powers that came from the building or the surrounding of the building. In making a cladding the wind energy forms with wind pressure by means of energy transformation methods. The assessment for the building cladding was surrounded of wind speed and wind pressure that was carried out as a result of numerical simulation of wind environment and wind pressure which is coefficient around the high-rise building with the computational fluid dynamics. In case of the obtained wind energy from the pressure of the building cladding was estimated by the simulation of CFD of the building. The wind energy at this case was calculated by energy transform methods: the wind pressure coefficients were obtained from the simulated model for wind environment using CFD as follow. The concept for the factor of $E_f$ was suggested in this study. $$C_p=\frac{P_{surface}}{0.5{\rho}V^{2ref}}$$ $$E_c=C_p{\cdot}E_f$$ Where $C_p$ is wind pressure coefficient from CFD, $E_f$ means energy transformation parameter from the principle of the conservation of energy and $E_c$ means energy from the building cladding. The other wind energy that is $E_p$ was assessed by wind power on the building or building surroundings. In this case the small wind power system was carried out for wind energy on the place with the building and it was simulated by computational fluid dynamics. Therefore the total wind energy in the building was calculated as the follows. $$E=E_c+E_p$$ The energy transformation, which is $E_f$ will need more research and estimation for various wind situation of the building. It is necessary for the assessment to make a comparative study about the wind tunnel test or full scale test.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.358-359
• /
• 2012

최근 분극 특성이 상이한 무분극 GaN 에피성장에 관한 심도 있는 연구와 함께 전자-전공 캐리어의 주입 및 캐리어의 거동, 방출되는 편광 특성 및 다양한 물리적 특성들에 대해 보고되고 있으며, 광학적 특성 및 물리적 특성의 확보를 위한 많은 연구가 활발히 진행 중이다 [1]. GaN의 ohmic 접촉(ohmic contact)의 형성은 발광 다이오드(light emitting diode), 레이저 다이오드(Laser), 태양전지(solar cell)와 같은 고신뢰도, 고효율 광전자 소자를 제조하기 위해서는 매우 중요하다 [2]. 그러나 이와 함께 병행 되어야 할 무분극 p-GaN 의 ohmic contact에 관한 연구는 많이 이루어지고 있지 않는 실정이다. 따라서 본 논문에서는 r-plane 사파이어 기판 상에 성장된 p-GaN에서의 ohmic 접촉 형성 연구를 위하여 Ni/Au ohmic 전극의 접촉저항 특성을 연구하였다. 본 실험에서는 성장된 a-plane GaN의 Hole농도가 $3.09{\times}1017cm3$ 인 시편을 사용하였다. E-beam evaporation 장비를 이용하여 Ni/Au를 각각 20 nm 그리고80 nm 증착 하였으며 비접촉저항을 측정하기 위해 Circle-Transfer Length Method (C-TLM) 패턴을 사용하였다. 샘플은 RTA (Rapid Thermal Annealing)를 사용하여 $300^{\circ}C$에서 $700^{\circ}C$까지 온도를 변화시키며 전기적 특성을 비교하여 그림 1(a) 나타내었다. 그림에서 알 수 있듯이 $400^{\circ}C$에서 가장 낮은 비접촉저항 값인 $6.95{\times}10-3{\Omega}cm2$를 얻을 수 있음을 발견하였다. 이 때의 I-V curve 도 그림1(b)에 나타낸 바와 같이 열처리에 의해 크게 향상됨을 알 수 있다. 그러나, $500^{\circ}C$ 이상 온도를 증가시키면 다시 비접촉 저항이 증가하는 것을 관찰하였다. XRD (x-Ray Diffraction) 분석을 통하여 $400^{\circ}C$ 이상열처리 온도가 증가하면 금속 표면에 $NiO_2$가 형성되며, 이에 따라 오믹특성이 저하 된다고 사료된다. 또한 $Ni_3N$의 존재를 확인 하였으며 이는 nonpolar surface의 특성으로 인해 nitrogen out diffusion 현상이 동시에 발생하여 계면에는 dopant로 작용하는 질소 공공을 남기고 표면에 $Ni_3N$을 형성하여 ohmic contact의 특성이 저하되기 때문인 것으로 사료된다.

• KSBB Journal
• /
• v.14 no.4
• /
• pp.422-428
• /
• 1999

A transformat Alcaligence eutrophus GA5 harboring phbC gene from A. latus was cultivated for production of Poly(3-hydroxybutyrate-4-hydroxybutyrate)[P(3HB-4HB)] containing high molar fraction of 4-hydroxybutyrate(4HB)] containing high molar fraction of 4-hydroxybutyrate(4HB). Transformation did not influenced significantly on total cell growth, on total cell growth, concentration, and content of P(3HB-4HB), however, significantly influenced on 4HB molar fraction in P(3HB-4HB) increasing from 12.3 to 23.5 mol% after 48 h cultivation in two-stage using 1.0%(W/V) of ${\gamma}$-butyrolactone as a precursor compare to parent strain. Above increment may be due to the accelerated polymerization between 3HB and 4HB converted from precusor compound by amplified phbC gene. Citrate increased remarkbly total cell mass and P(3HB-4HB) concentration, but did not influenced on the molar fraction of 4HB, meanwhile, magnesium ion influenced on P(3HB-4HB) concentration and 4HB molar fraction significantly. The two-stage cultivation method was modified, in such a way minimizing P(3HB) accumulated inside of cell grown at first-stage, consquently, 26.3% of P(3HB-4HB) containing 61.0 mol% of 4HB fraction was obtained after 72hr. Furthermore, semi-homopolymeric P(4HB) containing 92.0 mol% of 4Hb was obtained, and its structure was confirmed by $^1$H-NMR.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.85-89
• /
• 2021

AlGaN-based UV-C light-emitting diodes (LEDs) were applied for p-type activation by electrochemical potentiostatic activation (EPA). The p-type activation efficiency was increased by removing hydrogen atoms through EPA treatment using a neutral Mg-H complex that causes high resistance and low conductivity. A neutral Mg-H complex is decomposed into Mg^- and H⁺ depending on the key parameters of solution, voltage, and time. The improved hole carrier concentration was confirmed by secondary ion mass spectroscopy (SIMS) analysis. This mechanism eventually improved the internal quantum efficiency (IQE), the light extraction efficiency, the leakage current value in the reverse current region, and junction temperature, resulting in better UV-C LED lifetime. For systematic analysis, SIMS, Etamax IQE system, integrating sphere, and current-voltage measurement system were used, and the results were compared with the existing N₂-annealing method.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.73.1-73.1
• /
• 2010

For the successful cold starting of a fuel cell engine, either internal of external heat supply must be made to overcome the formation of ice from water below the freezing point of water. In the present study, switchable vanadium oxide compounds as variable temperature-electrical resistance materials onto the surface of flat metallic bipolar plates have been prepared by a dip-coating technique via an aqueous sol-gel method. Subsequently, the chemical composition and micro-structure of the polycrystalline solid thin films were analyzed by X-ray diffraction, X-ray fluorescence spectroscopy, and field emission scanning electron microscopy. In addition, it was carefully measured electrical resistance hysteresis loop over a temperature range from $-20^{\circ}C$ to $80^{\circ}C$ using the four-point probe method. The experimental results revealed that the thin films was mainly composed of Karelianite $V_2O_3$ which acts as negative temperature coefficient materials. Also, it was found that thermal dissipation rate of the vanadium oxide thin films partially satisfy about 50% saving of the substantial amount of energy required for ice melting at $-20^{\circ}C$. Moreover, electrical resistances of the vanadium-based materials converge on an extremely small value similar to that of pure flat metallic bipolar plates at higher temperature, i.e. $T{\geq}40^{\circ}C$. As a consequence, experimental studies proved that it is possible to apply the variable temperature-electrical resistance material based on vanadium oxides for the cold starting enhancement of a fuel cell vehicle and minimize parasitic power loss and eliminate any necessity for external equipment for heat supply in freezing conditions.

• Journal of Surface Science and Engineering
• /
• v.37 no.2
• /
• pp.71-75
• /
• 2004

The technology of $C_{60}$ fullerite films preparation by means of gas-phase deposition and structure of fullerite films are described. A three-channel flow plant was used to obtain fullerite films. The films were deposited in the flow of inert gas under reduced pressure onto a cooled silicon or sapphire substrate placed inside the reaction chamber of the plant. The plant allows one to obtain the films of pure fullerenes and to synthesise the films from fullerene compounds and doped fullerenes. The structure of two types of films were investigated by FE-SEM and SEM techniques: pure fullerite films onto silicon and sapphire substrates as well as compound films were studied by FE-SEM technique. All samples have shown columnar structure with high level of porosity. The synthesis of films composed of fullerene and its compounds for use in electronics is demonstrated to be promising. For example, experiments confirm the possibility to use fullerite films in sensor electronics to produce humidity and thermal sensors. It is also possible to use the sensitivity of these films to isotropic pressure. The experiments with $C_{60}$-Cu-J films have shown quite strong dependence of their resistance on pressure of different sort of medium-gas that could be used in gas-sensitive sensors. The structure and preparation technology of resistive sensor based on fullerite films are described.bed.

• BMB Reports
• /
• v.39 no.1
• /
• pp.105-110
• /
• 2006

We have screened 766 strains of fungi from the BIOTEC Culture Collection (BCC) for xylanases working in extreme pH and/or high temperature conditions, the so-called extreme xylanases. From a total number of 32 strains producing extreme xylanases, the strain BCC7928, identified by using the internal transcribed spacer (ITS) sequence of rRNA to be a Marasmius sp., was chosen for further characterization because of its high xylanolytic activity at temperature as high as $90^{\circ}C$. The crude enzyme possessed high thermostability and pH stability. Purification of this xylanase was carried out using an anion exchanger followed by hydrophobic interaction chromatography, yielding the enzyme with >90% homogeneity. The molecular mass of the enzyme was approximately 40 kDa. The purified enzyme retained broad working pH range of 4-8 and optimal temperature of $90^{\circ}C$. When using xylan from birchwood as substrate, it exhibits $K_m$ and $V_{max}$ values of $2.6{\pm}0.6\;mg/ml$ and $428{\pm}26\;U/mg$, respectively. The enzyme rapidly hydrolysed xylans from birchwood, beechwood, and exhibited lower activity on xylan from wheatbran, or celluloses from carboxymethylcellulose and Avicel. The purified enzyme was highly stable at temperature ranges from 50 to $70^{\circ}C$. It retained 84% of its maximal activity after incubation in standard buffer containing 1% xylan substrate at $70^{\circ}C$ for 3 h. This thermostable xylanase should therefore be useful for several industrial applications, such as agricultural, food and biofuel.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.262-268
• /
• 1999

Polycarbonate (PC) and Polymethylmethacrylate (PMMA) surface was modified by ion assisted reaction (IAR) technique to obtain the hydrophilic functional groups and improve the wettability. In conditions of ion assisted reaction, ion beam energy was changed from 500 to 1500eV, and ion dose and oxygen gas blown rate were fixed $1\times10^{16}$ ions/$\textrm{cm}^2$ and 4ml/min, respectively. Wetting angle of water on PC and PMMA surface modified by $Ar^+$ ion without blowing oxygen at 4ml/mon showed $5^{\circ}$ and $10^{\circ}$. Changes of wetting angle with oxygen gas and $Ar^+$ ion irradiation were explained by considering formation of hydrophilic group due to a reaction between irradiated polymer chain by energetic ion irradiation and blown oxygen gas. X-ray photoelectron spectroscopy analysis shows that hydrophilic groups such as -C-O, -(C=O)- and -(C=O)-O- are formed on the surface of polymer by chemical interaction. The polymer surface modification using ion assisted reaction only changed the surface physical properties and sept the bulk properties. In comparison with other modification methods, the surface modification by IAR treatment was chemically stable and enhanced the adhesion between metal and polymer surface. The applications of various kinds of polymer surface modification methods, metal and polymer surface. The applications of various kinds of polymer surface modification could be appled to the new materials about hydrophilic surface properties by IAR treatment. The adhesion between metal film and polymer measured by Scotch tape test whether the hydrophilic surfaces could improve the adhesion strength or not.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.8
• /
• pp.803-809
• /
• 2009

Recent evidence has revealed the occurrence of an apoptotic phenotype in Candida albicans that is inducible with environmental stresses such as acetic acid, hydrogen peroxide, and amphotericin B. In the present study, we found that the Chinese herbal medicine Baicalein (BE), which was one of the skullcapflavones, can induce apoptosis in C. albicans. The apoptotic effects of BE were detected by flow cytometry using Annexin V-FITC and DAPI, and it was confirmed by transmission electron microscopy analysis. After exposure to 4 ${\mu}g$/ml BE for 12 h, about 10% of C. albicans cells were apoptotic. Both the increasing intracellular levels of reactive oxygen species (ROS) and upregulation of some redox-related genes (CAP1, SOD2, TRR1) were observed. Furthermore, we compared the survivals of CAP1 deleted, wild-type, and overexpressed strains and found that Cap1p attenuated BE-initiated cell death, which was coherent with a higher mRNA level of the CAP1 gene. In addition, the mitochondrial membrane potential of C. albicans cells changed significantly (p<0.001) upon BE treatment compared with control. Taken together, our results indicated that BE treatment induced apoptosis in C. albicans cells, and the apoptosis was associated with the breakdown of mitochondrial membrane potential.