• Horticultural Science & Technology
• /
• v.35 no.1
• /
• pp.46-58
• /
• 2017

This study was conducted to investigate the optimal conditions for spore germination, prothallus propagation, sporophyte formation and seedling growth in Microlepia strigosa (Thunb.) C. Presl. Spore germination and prothallus development were promoted by low concentrations of Knop medium nutrient solution. The optimal medium for prothallus propagation and antheridium formation was 2X MS medium with 3% sucrose. The activated charcoal content of the medium did not affect prothallus proliferation. Among the various combinations of culture soil (bedding soil, peat moss, perlite and decomposed granite), a mixture of bedding soil, peat moss and decomposed granite at a ratio of 1 : 1 : 1 (v : v : v) had a positive effect on sporophyte formation. The most efficient conditions for promoting the growth of whole plants (sporophyte seedlings) were 50 - cell plug trays filled with a mixture of bedding soil and decomposed granite at a 2 : 1 (v : v) ratio.

• Korean Journal of Environmental Biology
• /
• v.17 no.4
• /
• pp.439-448
• /
• 1999

To investigate the population dynamics and survival of Genus Vibrio, population densities of aerobic saprophytic bacteria and Vibrio groups were measured 4 times in the intertidal waters of the Yellow Sea near Kunsan from November, 1997 to June, 1998. The distribution of heterotrophic bacteria during the survey periods by plate count and direct count method ranged from 1.2$\pm$0.6$\times$10$^3$~2.0$\pm$1.5$\times$10$^4$CFU ml­$^1$and from 6.0$\pm$4.0$\times$10$^{5}$ ~1.9$\pm$1.5$\times$10$^{7}$ cells ml­$^1$, respectively. Vibrio groups were distributed in the range of 1$\times$10 and 6$\pm$2.2$\times$10$^2$CFU ml­$^1$. The proportion of Vibrio groups to total heterotrophic bacteria was between 0.1 and 6% during the survey periods. A total of 51 isolates was obtained from TCBS agar plates and identified to species level by Biolog Identification System$^{TM}$. As a result, dominant genera were V, mediterranei, V aitguillarum, tr metschnikovii, and V. parahaemolyticus, and isolates were clustered into 26 groups based on the relatedness of average linkage clustering method at 70% level. As for the susceptibility of 51 isolates to 7 kinds of antibacterial agents (gentamicin, ampicillin, chlorarnphenicol, streptomycin, kanamycin, tetracycline, carbenicillin), 96% of isolates showed high resistance to more than one antibiotics and 65% of isolates contained a plasmid, of which size was observed greater than 12 kb, The number of cells of 3 tested strains (V. anguillarum, V. vulnificus, and V. metschnikovii) in filtered aged seawater decreased by approximately 1 to 5 orders of magnitude during 30-d incubation. In most cases, the numbers of cells decreased rapidly until day 3, then decreased slowly by day 30. The number of cells incubated at 15$^{\circ}C$ showed higher survival than those at 4$^{\circ}C$ and $25^{\circ}C$. These results may be considered for the basic supporting data in the risk assessment of vibriosis in summer.r.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.171-177
• /
• 2001

The thermal and mechanical properties of amorphous Z $r_{62-x}$N $i_{10}$C $u_{20}$A $l_{8}$ $Ti_{x}$ (x=3, 6, 9at%) alloys were investigated. The crystallization process was confirmed as amorphous longrightarrow amorphous + Z $r_2$A $l_3$+ Zr + (Ni,Ti) longrightarrow Z $r_2$Cu + Al + (Ni,Ti) for 3at%Ti, amorphous longrightarrow amorphous + Al longrightarrow $Al_2$Ti + NiZr + CuTi for 6at%Ti and amorphous longrightarrow amorphous + Zr + Al longrightarrow Zr + $Al_2$Zr + Al $Ti_3$+ CuTi for 9at%Ti. lickers hardness ( $H_{v}$ ) increased with increasing volume fraction( $V_{f}$ ) of pricipitates for all concerned compositions. Tensile fracture strength ($\sigma_{f}$ ) showed a maximum value 1219MPa at $V_{f}$ = 38% for 3at%Ti, 1203MPa at $V_{f}$ = 2% for 6at%Ti and 1350MPa at $V_{f}$ = 5% for 9at%Ti. The $\sigma_{f}$ was rapidly decreased after showing the maximum value. The $V_{f}$ corresponding to rapidly decreased $\sigma_{f}$ coincided with the $V_{f}$ transited from ductile to brittle fracture surface.ace.

• Journal of the Korean Chemical Society
• /
• v.18 no.4
• /
• pp.267-271
• /
• 1974

The tetradentate schiff base, N,N'-bis(salicylaldehyde)-ethylene diimine has been reacted with a series of Mo(IV), Mo(V), Mo(IV), and Mo(III) oxidation states to form new Complexes; $[MoO_2(C_{16}H_{14}O_2N_2)], (MoO(C_{16}H_{14}O_2N_2)]_2O, (Mo(SCN)(C_{16}H_{14}O_2N_2)]_2O, and (Mo(H_2O)(C_{16}H_{14}O_2N_2)]_2O.$ These complexes have hexa coordinated configurations and the mole ratio of these ions to the ligand was 1:1. These complexes have been identified by visible spectra, infrared specra, T.G.A., D.T.A., and elemental analysis.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.125-137
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.110-110
• /
• 1998

GaN는 직접천이형 에너지 캡을 가지며 In과 화합물을 형성할 경우 1.geV-3.4eV까지 다양한 에너지 캡을 가지므로 청색 발광소자 고출력소자 고온 전자소자둥 웅용성이 많 은 물절로서 각광을 받고 있다. 그러나 G랴‘에 적합한 기판이 없다는 문제점으로 인하여 F FET, LD와 같은 다양한 구조의 웅용에 제 약이 따랐다. 이에 본 연구에서는 RF(radio frequency) Plasma-Assisted MBE( molecular beam e epitaxy )를 이용하여 InxGaj xN/G암J 양자우물 구조를 성장하였다. 이렇게 성장된 I InxGaj xN 박막과 InxGaj xN/GaN 양자우물구조의 특성의 분석은 광학적 특성올 PL( p photoluminescence ) , 결 정 성 의 분석 은 XRD ( x-ray diffraction ), 표면 과 단변 의 계 변 특성은 SEM(scanning electron microscopy)을 이용하여 분석하였다. 저온 PL의 측정결 과 기판온도를 680$^{\circ}$C로 고정한 후 In cell의 온도를 650$^{\circ}$C에서 775$^{\circ}$C까지 증가함에 따라 I InxGaj xN에 관계된 피크위치가 약3이neV정도 red shift 함을 관찰할 수 있었다. 한편 I InxGaj xN/GaN 양자우물구조의 경우 PL피크가 3.2없eV로써 InxGaj- xN의 PL 피크에 비 해 에서 약 25me V 고에너지 이동이 관측되었으며 이것은 우불 내에서 에너지레벨의 c confinement효과에 의해 에너지의 변화에 의한 것엄올 확인하였으며, 양자우물 구조에서 우물의 두께를 줄임에 따라 변화 폭은 1이neV정도 고에너지 이동을 관찰할 수 있었다. X XRD 측정의 결과 In의 mole fraction에 따라 격자상수의 변화를 관찰하였으며, 결정 성의 변화를 피크의 세기로 관찰하였다 .. XRD로 판단한 In의 mole fraction은 0.2임을 알 았다 .. SEM 측정은 표변과 단면의 측정으로서 표연특성과 단면의 특성을 InxGaj xN, I InxGaj xN/GaN 양자우물 구조 모두 알아보았다. 측정 결과 InxGaj-xN의 성 장조건으로 기판온도가 낮아지면서 표면의 거칠기 정도가 증가하였으며,680$^{\circ}$C의 기판온도에서 성장 한 양자우물 구조에 있어서 매끄라운 표면올 얻올 수 있었다.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.69-72
• /
• 2002

B $i_{3.3}$L $a_{0.7}$ $Ti_3$ $O_{12}$(BLT) 강유전체 박막을 $Al_2$ $O_3$/Si 기판위에 졸-겔(sol-gel)법으로 스핀 코팅하여 Metal-Ferroelectric-Insulator-Silicon (MFIS) 구조를 형성하였다. 박막의 결정화를 위해 as-coated 박막을 산소분위기에서 $650^{\circ}C$ 및 $700^{\circ}C$에서 30분 동안 후속열처리를 실시하였다. BLT 박막의 열처리 온도를 $650^{\circ}C$에서 $700^{\circ}C$로 증가시킴에 따라서 c축으로 우선 배향되는 경향을 보였으며, FWHM 값이 감소하여 결정성이 향상됨을 확인할 수 있었다. $700^{\circ}C$에서 열처리된 BLT 박막의 memory window는 약 2.5V (인가전압 5V)를 나타내었으며, 누설전류는 약 1.5x$10^{-7}$ A/$\textrm{cm}^2$를 나타내었다.다.다.

• International Journal of Advanced Culture Technology
• /
• v.10 no.4
• /
• pp.316-321
• /
• 2022

Since 2019, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has spread rapidly, infecting millions of people worldwide. On March 11, 2020, the World Health Organization declared coronavirus disease (COVID-19) a pandemic owing to the worldwide spread of SARS-CoV-2, which created an unprecedented burden on the global healthcare system. In this context, there are increasing concerns regarding co-infections with other respiratory viruses, such as the influenza virus. In this study, clinical data of patients infected with SARS-CoV-2 and other respiratory viruses were compared with patients infected with SARS-CoV-2 alone. The hematology and blood biochemistry results of 178 patients infected with SARS-CoV-2 , who were tested on admission, were retrospectively reviewed. In patients with SARS-CoV-2 and adenovirus co-infection, C-reactive protein levels were elevated on admission, whereas lactate dehydrogenase (LDH), prothrombin time, international normalized ratio, activated partial thromboplastin clotting time, and bilirubin values were all within the normal range. Moreover, patients with SARS-CoV-2 and human bocavirus co-infection had low LDH and high bilirubin levels on admission. These findings reveal the clinical features of respiratory virus and SARS-CoV-2 co-infections and support the development of appropriate approaches for treating patients with SARS-CoV-2 and other respiratory virus co-infections.

• Journal of Sensor Science and Technology
• /
• v.11 no.5
• /
• pp.309-318
• /
• 2002

A stoichiometric mixture of evaporating materials for $CdIn_2S_4$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $CdIn_2S_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $630^{\circ}C$ and $420^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CdIn_2S_4$ single crystal thin films measured with Hall effect by van der Pauw method are $9.01{\times}10^{16}\;cm^{-3}$ and $219\;cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the $CdIn_2S_4$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=2.7116\;eV-(7.74{\times}10^{-4}\;eV)T^2/(T+434)$. The crystal field and the spin-orbit splitting energies for the valence band of the $CdIn_2S_4$ have been estimated to be 0.1291 eV and 0.0248 eV, respectively, by means of the photocurrent spectra and the Hopfield quasi cubic model. These results indicate that the splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}5$ states of the valence band of the $AgInS_2$/GaAs epilayer. The three photocurrent peaks observed at 10K areascribed to the $A_1$-, $B_1$-, and C1-exciton peaks for n = 1.