• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.146.2-146.2
• /
• 2012

2008년부터 2012년에 걸친 관측기간 동안 총 21일간 관측하여 AA UMa의 BVRI 광도 곡선을 획득하였다. AA UMa의 I 필터 광도 곡선은 이번에 처음으로 얻어진 것이다. 또한 극심시각을 추가적으로 획득하기 위하여 2005 ~ 2008년까지 총 8일간 AA UMa의 극심 부근의 측광관측을 수행하였고, SuperWASP에서 공개하는 AA UMa의 측광 자료를 수집하여 총 31개의 새로운 극심시각을 결정하였다. 우리의 새로운 극심시각을 포함하여 83년 동안의 AA UMa 극심시각을 수집하여 총 250개의 극심시각으로 주기 변화연구를 수행하였다. 그 결과 AA UMa 계는 $3.30{\times}10^{-11}d/yr$의 영년 주기 증가 위에 58.7년의 주기적인 변화가 겹쳐 발생한다. 주기적인 변화의 원인이 제3천체에 의해 발생한다고 가정했을 때 제3천체의 최소 질량은 $0.28M_{\odot}$이다. 이전 연구자의 광도곡선(Meinunger(1976), Wang et al.(1988), Lee et al(2011))을 수집하여 우리의 광도곡선(2008, 2012)과 함께 각각 주기변화가 보정된 통일된 기산점을 사용하여 광도곡선을 분석하였다. 모든 광도곡선에서 0.75 위상에서 밝기가 더 어두워지는 O'Connell effect가 발생하였고, 일부 광도곡선은 부식에서 식의 깊이가 주식보다 깊어지는 시기를 가진다. 이는 스펙트럼 유형이 F0-F5보다 만기형 별에서 흑점이 부식의 깊이에 영향을 주어 주식보다 깊어지는 AC Boo, TY UMa 등에서 보여 지는 특징이다. 우리는 WD 프로그램을 이용하여 광도곡선 중 B-V 색지수 그래프에서 식 이외부분에서 변화가 적고 광도곡선의 O'Connell effect의 크기가 작은 2008 광도곡선으로 광도해를 결정하였다. 전형적인 TY UMa형 별과 같이, 우리의 광도해 역시 W-subtype의 결과를 나타낸다. 결정된 광도해를 다른 광도곡선에도 적용시켜 광도곡선에 나타나는 흑점의 영향을 살펴보았다. 마지막으로 주기 분석 결과와는 달리 제 3천체의 광도는 검출 되지 않았다.

• Structural Engineering and Mechanics
• /
• v.40 no.5
• /
• pp.637-654
• /
• 2011

The present paper studies the variation of the natural frequencies and mode shapes of rectangular plates carrying a three degree-of-freedom spring-mass system (subsystem), when the subsystem changes (stiffness, mass, moment of inertia, location). An analytical approach based on Lagrange multipliers as well as a finite element formulation are employed and compared. Numerically reliable results are presented for the first time, illustrating the convenience of using the present analytical method which requires only the solution of a linear eigenvalue problem. Results obtained through the variation of the mass, stiffness and moment of inertia of the 3-DOF system can be understood under the effective mass concept or Rayleigh's statement. The analysis of frequency values of the whole system, when the 3-DOF system approaches or moves away from the center, shows that the variations depend on each particular mode of vibration. When the 3-DOF system is placed in the center of the plate, "new" modes are found to be a combination of the subsystem's modes (two rotations, traslation) and the bare plate's modes that possess the same symmetry. This situation no longer exists as the 3-DOF system moves away from the center of the plate, since different bare plate's modes enable distinct motions of the 3-DOF system contributing differently to the "new' modes as its location is modified. Also the natural frequencies of the compound system are nearly uncoupled have been calculated by means of a first order eigenvalue perturbation analysis.

• International Journal of Automotive Technology
• /
• v.7 no.1
• /
• pp.1-7
• /
• 2006

The ignition delay of a dual fuel system has been numerically investigated by adopting a constant volume chamber as a model problem simulating diesel engine relevant conditions. A detailed chemical kinetic mechanism, consisting of 28 species and 135 elementary reactions, of dimethyl ether (DME) with methane ($CH_{4}$) sub-mechanism has been used in conjunction with the multi-dimensional reactive flow KIVA-3V code to simulate the autoignition process. The start of ignition was defined as the moment when the maximum temperature in the combustion vessel reached to 1900 K with which a best agreement with existing experiment was achieved. Ignition delays of liquid DME injected into air at various high pressures and temperatures compared well with the existing experimental results in a combustion bomb. When a small quantity of liquid DME was injected into premixtures of $CH_{4}$/air, the ignition delay times of the dual fuel system are longer than that observed with DME only, especially at higher initial temperatures. The variation in the ignition delay between DME only and dual fuel case tend to be constant for lower initial temperatures. It was also found that the predicted values of the ignition delay in dual fuel operation are dependent on the concentration of the gaseous $CH_{4}$ in the chamber charge and less dependent on the injected mass of DME. Temperature and equivalence ratio contours of the combustion process showed that the ignition commonly starts in the boundary at which near stoichiometric mixtures could exists. Parametric studies are also conducted to show the effect of additive such as hydrogen peroxide in the ignition delay. Apart from accurate predictions of ignition delay, the coupling between multi-dimensional flow and multi-step chemistry is essential to reveal detailed features of the ignition process.

• 대한예방의학회:학술대회논문집
• /
• 1994.02b
• /
• pp.206-233
• /
• 1994

The Medical Research Council has for some years encouraged collaborative clinical trials in leukaemia and other cancers, reporting the results in the medical literature. One unreported result which deserves such publication is the development of the expertise to design and analyse such trials. This report was prepared by a group of British and American statisticians, but it is intended for people without any statistical expertise. Part!, which appears in this issue, discusses the design of such trials; Part II, which will appear separately in the January 1977 issue of the Journal, gives full instructions for the statistical analysis of such trials by means of life tables and the logrank test, including a worked example, and discusses the interpretation of trial results, including brief reports of particular trials. Both parts of this report are relevant to all clinical trials which study time to death, and would be equally relevant to clinical trials which study time to other particular classes of untoward event: first stroke, perhaps, or first relapse, metastasis, disease recurrence, thrombosis, transplant rejection, or death from a particular cause. Part I, in this issue, collects together ideas that have mostly already appeared in the medical literature, but Part II, next month, is the first simple account yet published for non-statistical physicians of how to analyse efficiently data from clinical trials of survival duration. Such trials include the majority of all clinical trials of cancer therapy; in cancer trials, however, it may be preferable to use these statistical methods to study time to local recurrence of tumour, or to study time to detectable metastatic spread, in addition to studying total survival. Solid tumours can be staged at diagnosis; if this, or any other available information in some other disease is an important determinant of outcome, it can be used to make the overall logrank test for the whole heterogeneous trial population more sensitive, and more intuitively satisfactory, for it will then only be necessary to compare like with like, and not, by chance, Stage I with Stage III.

• Korean Journal of Clinical Pharmacy
• /
• v.19 no.1
• /
• pp.43-49
• /
• 2009

토브라마이신은 그람음성균 감염에 사용하는 아미노글리코사이드계 항생제로 이독성 및 신독성 등의 부작용과 큰 개인차로 혈중농도 모니터를 통한 투여계획이 필요한 약물이다. 본 연구에서는 16명의 위암환자에서 비선형 최소자승 회귀분석과 베이시안 분석에 의한 토브라마이신의 약물동태에 분석오차의 영향에 대하여 연구하였다. 약물투여는 토브라마이신 1-2 mg/kg을 30분에 걸쳐 8시간 간격으로 등속 주입하였으며, 혈액 채취는 정상상태에 도달되었다고 판단되는 첫 약물투여 72시간 후에, 약물 주입 5분전과 주입이 끝난 뒤 30분과 2시간에서 세차례 채취하였다. 혈청중 약물농도는 형광편광면역법으로 측정 하였다. 분석오차를 위해 0, 1, 2, 4, 8 및 12 ${\mu}g/mL$에 해당하는 토브라마이신 혈중농도(C)을 네차례 측정하여 각 혈중농도의 표준편차 (SD)을 구하였다. 토브라마이신 분석오차를 구하기 위한 다항식이 SD = 0.0224+0.0540C+0.00173C2, $R^2$ = 0.935이었다. 이 식에서 구한 SD 값으로 분석시 가중치를 주었을 때, 비선형 최소자승 회귀분석에 의한 토브라마이신의 약물동태학적 파라메타 ($V_d$, $K_{el}$, $K_{slpoe}$, $t_{1/2}$)에 유의성있는 영향을 주었으나, 베이시안 분석에 의한 토브라마이신의 약물동태학적 파라메타에는 영향이 없었다. 이 다항식으로 부터 구한 분석오차를 토브라마이신의 비선형 최소자승 회귀분석을 이용한 약물동태 연구 및 파라메타 분석에 적용하여 좀 더 정확한 투여용량을 결정할 수 있으며, 더 나아가 토브라마이신 약물동태 시뮬레이션 연구에 응용할 수 있다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.9
• /
• pp.835-843
• /
• 2008

We have fabricated the source-drain electrodes for OTFTs by screen printing method and manufactured Ag pastes as conductive paste. To obtain excellent conductivity and screen-printability of Ag pastes, the dispersion characteristics of Ag pastes prepared from two types of acryl resins with different molecular structures and Ag powder treated with caprylic acid, triethanol amine and dodecane thiol as surfactant respectively were investigated. The Ag pastes containing Ag powder treated with dodecane thiol having thiol as anchor group or AA4123 with carboxyl group(COOH) of hydrophilic group as binder resin exhibited excellent dispersity. But, Ag pastes(CA-41, TA-41, DT-41) prepared from AA4123 fabricated the insulating layer since the strong interaction between surface of Ag powder and carboxyl group(COOH) of AA4123 interfered with the formation of conduction path among Ag powders. The viscosity behavior of Ag pastes exhibited shear-thinning flow in the high shear rate range and the pastes with bad dispersion characteristic demonstrated higher shear-thinning index than those with good dispersity due to the weak flocculated network structure. The output curve of OTFT device with a channel length of 107 ${\mu}m$ using screen-printed S-D electrodes from DT-30 showed good saturation behavior and no significant contact resistance. And this device exhibited a saturation mobility of $4.0{\times}10^{-3}$ $cm^2/Vs$, on/off current ratio of about $10^5$ and a threshold voltage of about 0.7 V.

• Journal of Embryo Transfer
• /
• v.9 no.1
• /
• pp.23-29
• /
• 1994

The long term goal of this research is to develop an efficient procedure for large scale production of genetically identical or cloned animals. To improve nuclear transpalntation efficiency in the rabbit, this study evaluated the age of nuclear recipient oocytes on the different steps of nuclear transplantation. The ovulated oocytes in different ages were collected from the superovulated does by flushing oviducts with Dulbecco's phosphate buffered saline(D-PBS) supplemented with 10% fetal calf serum(FCS) from 13 to 15, 17 to 20 and 23 to 26 hours after hCG injection. The denuded oocytes were used as nuclear recipient cytoplasm following enucleation by micromanipulation. The blastomeres separated from the 8-cell embryos were used as nuclear donor. The enucleated oocytes receiving a blastomere in the perivitteline space were fused in the 0.28 M mannitol solution at 1.5 kV/cm, 60 sec for three times. The fused oocytes were co-cultured with the monolayered rabbit oviductal epithelial cells in TGM-199 solution with 10% FCS for 72 hours at 37$^{\circ}C$ in a 5% $CO_2$ incubator. The cultured nuclear transplant embryos and in vivo developed embryos collected at 72 hours after hCG injection were stained with Hoechst 33342 dye. Their cell numbers were counted under a fluorescent microscope. The results obtained were summarized as follows ; 1. The aged oocytes(20 hrs. post hCG) showed significantly(P<0.05) higher fusionrates(70 ~ 90%) than the recently ovulated oocytes(30.8%) 2. The aged oocytes which were electrically activated and fused at 20 hours developed to blastocyst at significantly(P<0.05) high rate, while none of the recently ovulated oocytes developed to blastocyst. 3. Even though the aged oocytes at 23~26 hours showed higher fusion rate(85.7%), not only they were inadequate to manipulate but also their developmental potential to blastocyst was highly impaired. 4. The developmental potential in vitro of nuclear transplant embryos was significantly retarded than in vivo deveolped embryos.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.78-85
• /
• 2006

In textile industries, waste effluent containing zinc is generated during the manufacture of rayon yarn from the wood pulp or cotton linters. Due to the strict environmental regulations and the presence of toxic metallic and other constituents, the discharge of industrial effluents in the sewage or disposal of solid sludge as landfill is restricted. Before recycling of zinc as zinc sulphate solution to the spinning-bath of the rayon manufacturing plant the zinc sulphate solution must be free from calcium, which is deleterious to the process as gypsum precipitates with the increase in concentration and forms scale in the bath. In the present work an attempt has been made to develop a process following solvent extraction technique using thiophosphinic extractants, Cyanex 272 and 302 modified with isodecanol and diluted in kerosene to recover zinc from rayon effluent. Various process parameters viz. extraction of zinc from different concentration of solution, distribution ratio, selective extraction, O/A ratio on extraction and stripping from the loaded organic, complex formation in the organic phase etc. have been studied to see the feasibility of the process. The extractant Cyanex 302 has been found selective for the recovery of 99.99% of zinc from the effluent above equilibrium pH 3.4 maintaining the O/A ratio of 1/30 leaving all the calcium in the raffinate. It selectively extracted zinc in the form of complex $[R_{2}Zn.3RH]_{org}$ and retained all the calcium in the aqueous raffinate. The zinc from the loaded Cyanex 302 can be stripped with 10% sulphuric acid at even O/A ratio of 10 without affecting the stripping efficiency. The stripped solution thus obtained could be recycled in the spinning bath of the rayon plant. The raffinate obtained after the recovery of zinc could be disposed safely without affacting environment.

• Journal of The Korean Society of Inherited Metabolic disease
• /
• v.13 no.2
• /
• pp.104-110
• /
• 2013

Purpose: Phenylketonuria (PKU) is the first inherited metabolic disease of which treatment is known. We performed this study to find out clinical symptoms and prognosis of tetrahydrobiopterin (BH4) responsive PKU patients and genetic relation. Methods: Clinical, biochemical, genetic analysis were done retrospectively in 23 patients diagnosed BH4 responsive PKU in Soonchunhyang University Hospital from March 2000 to September 2012. Results: Patients were classified to mild hyperphenylalaninemia and mild phenylketonuria with initial plasma phenylalanine level below 20 mg/dL. After BH4 loading, blood phenylalanine decrease level ranged between 37% and 99%. Initial treatment with low phenylalanine formula or BH4 was started before 2 month after birth except 2 patients. And one of them resulted in developmental delay in language and social activity. The others showed satisfactory progress without developmental delay. In genetic analysis, of 46 allele, R241C allele mutation was identified most commonly (41%). R241C/A259T, R241C/R243Q, R241C/V388M, R241C/T278I was detected in 5 (21.7%), 3 (13%), 2 (8%), 2 (8%) patients, respectively. Conclusion: R241C mutation was detected most frequently in this study group and R243Q mutation which is known to be prevalent in Korean PKU patients was found in 4 patients (8.6%). Early diagnosis and treatment is important in PKU patients.

• Proceedings of the Ginseng society Conference
• /
• 2002.10a
• /
• pp.238-252
• /
• 2002

In order to screen out indicators for the discrimination of ginseng habitat, some physical and chemical characteristics of Korean red ginsengs (94 kinds) and Chinese red ginsengs (50 kinds) were analyzed by using a rheometer, an electronic nose system, a combined technique of solid phase micro-extraction (SPME) and gas chromatograph equipped with an electron capture detector (GC/ECD), an X-ray fluorescence spectrometer (XRF), an inductively coupled plasma mass spectrometer (ICP/MS), a near infrared spectrometer (NIRs) and high performance liquid chromatography equipped with evaporative light scattering detector (HPLC/ELSD). The results are summarized as follows: (i) The rhizome strengths of Korean red ginsengs were significantly higher than those of Chinese red ginsengs. (ii) The electronic nose patterns of Korean red ginsengs were significantly different from those of Chinese red ginsengs. (iii) Some unidentified peaks were detected not in the headspace of Korean red ginsengs but in the headspace of Chinese red ginsengs when the headspace volatiles prepared by the SPME technique were analyzed by GC/ECD. (iv) Either the content ratios of K to Ca or Mn to Fe were significantly different between Korean red ginsengs and Chinese red ginsengs. (v) The reflectance ratios of NIRs wavenumbers such as $904\;cm^{-1}\;to\;1088\;cm^{-1}$ for Korean red ginsengs were significantly different from those for Chinese red ginsengs. (vi) The content ratios of ginsenoside-Rg to ginsenoside-Re of Korean red ginsengs were significantly higher than those of Chinese red ginsengs. These results indicate that the rhizome strength, the electronic nose pattern, the occurrence of ECD-sensitive headspace volatile components, the content ratios of K to Ca and Mn to Fe, the NIRs pattern and the content ratio of ginsenoside-Rg to -Re may be indicators for the discrimination of ginseng habitat.