• Korean Journal of Optics and Photonics
• /
• v.30 no.4
• /
• pp.142-145
• /
• 2019

Normally, a corner cube retroreflector (CCRR) sheet is used as a retroreflective mirror array (RRMA) in a volumetric display. Each CCRR unit reflects light in the retroreflective direction, which is parallel to the incident light, and it makes a blurred image, as it shifts the position of light within its dimensions. Adopting a "curved planar wall" and "parabolic focusing" (x-axis), a hybrid-t(transverse direction)-RRMA is proposed, to improve the image quality and brightness. The improvement of image contrast is achieved by tuning a "linear v-shaped groove" structure to a "parabolic v-shaped groove". Also, the system has been simplified and the brightness enhanced 4 times by removing the half mirror.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1502-1509
• /
• 2006

In this paper, we proposed reliability and capacity enhancement methods for IEEE 802.15.3 HDR-WPAN (High Data Rate-Wireless Personal Area Network) system which is currently getting an interest in home network technology adopting a MIMO technique. We also analyzed performance or the proposed system through a computer simulation. The HDR-WPAN system using V-BLAST algorithm, transmitting the different signal vector to each other's sub-channel, can get the transmission speed of more than 110Mbps using two Tx/Px antenna without bandwidth expansion in TCM-64QAM mode. Also the proposed system has reliability of 104 at $E_b/N_0=35dB$ under the Rayleigh fading channel in case of two Tx/Rx antenna with MMSE algorithm. The HDR-WPAN system adopting V-BLAST method has its drawback which is very complicated to determine the decision-ordering at the receiver. But, the proposed system enhances the transmission capacity and reliability without extra bandwidth expansion by sending data streams to multiple antennas.

• The KIPS Transactions:PartC
• /
• v.13C no.6 s.109
• /
• pp.709-716
• /
• 2006

According to the increase of various AV media devices and contents in the digital home, the DLNA becomes to play an important role as the interoperability standard between then Since this guideline only focuses on the interoperability among home networked devices, media players, and media contents existing inside of the homenetwork, there is no retrieval and transmission method for sharing multimedia contents located over several homes via Internet. Additionally, this guideline lets device-detection and notification messages to be transmitted using W multicast methods, and current Internet environment cannot guarantee consistent IP multicast services, it has the limitation that it cannot retrieve and control DLNA devices in other digital homes remotely via the Internet. Therefore, in this paper, we propose the IHM(Inter-Home Media) proxy system and its operating mechanism to provide a way of sharing media contents distributed over multiple DLNA-based homes, through analyzing these limitations and building up a sharing method for A/V media contents distributed over the DLNA homes based on the dynamic or private IP networks. Our method removes the limitation on the user locations through sharing distributed media contents, and also makes cost-downs for storing media contents, from the view point of individual residents.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.6 s.312
• /
• pp.65-84
• /
• 2006

In this paper, we present an improved image formation model and propose a color image enhancement based on the model. In the presented image formation model, an input image is represented as a product of global illumination, local illumination, and reflectance. In the proposed color image enhancement, an input RGB color image is converted into an HSV color image. Under the assumption of white-light illumination, the H and S component images are remained as they are and the V component image only is enhanced based on the image formation model. The global illumination is estimated by applying a linear LPF with wide support region to the input V component image and the local illumination by applying a JND (just noticeable difference)-based nonlinear LPF with narrow support region to the processed image, where the estimated global illumination is eliminated from the input V component image. The reflectance is estimated by dividing the input V component image by the estimated global and local illuminations. After performing the gamma correction on the three estimated components, the output V component image is obtained from their product. Histogram modeling is next executed such that the final output V component image is obtained. Finally an output RGB color image is obtained from the H and S component images of the input color image and the final output V component image. Experimental results for the test image DB built with color images downloaded from NASA homepage and MPEG-7 CCD color images show that the proposed method gives output color images of very well-increased global and local contrast without halo effect and color shift.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.510-515
• /
• 1997

Packaging takes an extremely important element of optical module cost due primarily to the added complication of alignment between semiconductor devices and optical fiber, and many efforts have been devoted on reducing the cost by eliminating the complicated optical alignment procedures in passive manner. In this study, we fabricated silicon optical benches on which the optical alignments are accomplished passively. To improve the positioning accuracy of a flip-chip bonded LD, we adopted fiducial marks and solder dams which are self-aligned with V-groove etch patterns, and a stand-off to control the height and to improve the heat dissipation of LD. Optical sub-assemblies exhibited an average efficiency of -11.75$\pm$1.75 dB(1$\sigma$) from the LD-to-single mode fiber coupling and an average sensitivity of -35.0$\pm$1.5 dBm from the fiber and photodetector coupling.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.209-219
• /
• 1994

The practical application of riblet to three dimensional double model, for viscous drag reduction, was studied analytically by intergal solution to three dimensional turbulent boundary layers. The case of a V-groove riblet technique on the shear stress and boundary layer velocities were incooperated in the computation of the flow over a smooth slender ship hull. As the results the possible mechanism of turbulent drag reduction by riblets are then suggested based on detailed studies of near-wall turbulence characteristics. And a turbulent boundary layer calculation scheme based on a momentum integral method was modified for the computer program. An example of the calculation results is presented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.334-337
• /
• 2019

In this study, we built the data collection system to learn user's habit data by deep learning and to create an indoor environment according to the situation. The system consists of a data collection server and several sensor nodes, which creates the environment according to the data collected. We used Google Inception v3 network to analyze the photographs and hand-designed second DNN (Deep Neural Network) to infer behaviors. As a result of the DNN learning, we gained 98.4% of Testing Accuracy. Through this results, we were be able to prove that DNN is capable of extrapolating the situation.

• Journal of Korea Multimedia Society
• /
• v.12 no.11
• /
• pp.1509-1520
• /
• 2009

Contrary to ubiquitous environments, indoor computing environments like home network doesn't support user mobility. This paper suggests UPnP A/V multimedia system using prediction of mobility for adaption of seamless multimedia service. The multimedia system enables indoor mobile users to play multimedia contents by transferring the current session to an adjacent device automatically. The system represents users' contextual information by Five Ws and One H model, and predicts user's movements by using contextual information and transitions of locations. The prediction basically includes multiple locations so that it improves accuracy of prediction. We evaluated the suggested system using in accuracy of prediction, time for prediction, handover time for service, and the system showed that adapt ion of seamless multimedia service was enabled by using prediction of mobility on mobile user.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.76.1-76.1
• /
• 2010

Furnace를 이용한 $POCl_3$ 확산 공정은 실리콘 태양전지 제작과정에서 일반적으로 이용되는 에미터 층 형성 공정이다. 하지만, 확산 공정을 통해 P-N Junction을 형성할 경우 전면과 후면의 contact현상이 발생하게 되고 이를 제거하기 위해 Edge isolation 공정을 거치게 된다. 최근에는 레이저로 V 모양의 홈을 형성하는 방법이 이용되고 있다. 본 연구에서는 p-type 실리콘 웨이퍼 기판에 insulating barrier를 형성하여 edge isolation 공정을 없앤 Non-edge isolation공정을 제시한다. Non p-type 실리콘 웨이퍼에 insulating barrier를 형성한다. Insulating barrier가 형성된 BOE용액과 KOH에서의 견딤성 실험을 진행 하였다. 이후, p-type 단결정 실리콘 태양전지의 확산 공정을 진행하여 Non edge isolation 공정을 진행한 경우와 laser를 이용한 edge isolation 공정을 진행한 태양전지를 제작하여 특성을 비교하였다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.209-214
• /
• 2002

Mechanical micro-engineering is an easy and cheap way to fabricate micro-structures. If the application of the conventional machining method using flat-end mill becomes available for the micro-manufacturing process, it will be advanced as an extension of the conventional machining process. In this study, micro-grooves cutting using flat-end mill(($\phi$8) was performed. The characteristics on flat-end milling was investigated to improve machinability of micro-grooves. The experiments were performed according to variations of spindle revolution, depth of cut, and feed rate. Machinability through various cutting conditions was evaluated by surface geometry, tool wear, and cutting force. The results show that micro V-grooves of width(pitch) 29${\mu}{\textrm}{m}$ were acquired by flat-end milling. The maximum and minimum roughness of the wall of grooves was 438 and 67nm, respectively