• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1823-1826
• /
• 2002

The purpose of this experiment was to develope Triggered Vacuum Switch (TVS) for the high voltage and high current. The TVS has an array of rods of alternate polarity in which a fixed gap spacing is maintained between the rods. The cross section of each rod has trapezoidal shape. It consists of electrode, ceramic chamber, getter and trigger. Currently, triggered vacuum switch (TVS) with seal-off has been designed and fabricated at PAL. An experimentation and trigger devices for TVS were designed for testing characteristics of electricity. For making the prototype of TVS, it is developed of fabrication process and fined of electrode material. The fabrication of the TVS is a lot of process which have manufacturing of part, chemical clean, ceramic brazing and metal welding. The fabricated TVS is tested of leak for vacuum, hold-off voltage and conditioning of trigger system. The TVS has pinch-off after it is removed of gas in the TVS and activated of getter in degassing furnace. The prototype TVS tested about 20 kV, 75 kA, 83 ${\mu}s$ with 100 kJ capacitor bank and inductance 5 ${\mu}H$. This paper describes the results of tests and the characteristics of the switch.

• Current Photovoltaic Research
• /
• v.1 no.2
• /
• pp.109-114
• /
• 2013

$Cu_2ZnSnS_4$ (CZTS) nanoparticles were synthesized by a solvothermal method using copper (II) acetate, zinc acetate, tin chloride, and sulfur in diethylenetriamine solvent. Binary sulfide particles such as CuS, ZnS, SnS, and $SnS_2$ were obtained at $180^{\circ}C$; single-phase CZTS nanoparticles were obtained at $280^{\circ}C$. CZTS nanoparticles with spherical shape and grain size of 40 to 60 nm were obtained at $280^{\circ}C$. In the middle of 180 and $280^{\circ}C$, CZTS and ZnS phases were found. The time variation of reaction at $280^{\circ}C$ revealed that an amorphous state formed first instead of binary phases and then the amorphous phase was converted to crystalline CZTS state; it is different reaction path way from conventional solid-state reaction path of which binary phases react to form CZTS. CZTS films deposited and annealed from single-phase nanoparticles showed porous microstructure and poor adhesion. This indicates that a combination of CZTS and other flux phase is necessary to have a dense film for device fabrication.

• Journal of Biosystems Engineering
• /
• v.42 no.1
• /
• pp.44-55
• /
• 2017

Background: Heat recovery is one of the prominent ways to save a considerable amount of conventional fossil fuel and minimize its adverse effects on the environment. The rotary heat exchanger is one of the most effective and efficient devices for heat recovery or heat exchanging purposes. It is a regenerative type of heat exchanger, which has been studied and used for many heat recovery purposes. However, regenerative thermal wheels have been mostly used as heat recovery systems in buildings. For modeling a rotary regenerator, it is very important to numerically consider all the factors involved, such as effectiveness, rotational speed, geometrical size and shape, and pressure drop (${\Delta}p$). In recent times, several researchers have actively studied the rotary heat exchangers, both theoretically and experimentally. Reviews: In this paper different advances in the numerical modeling of regenerative rotary heat exchangers in relation to fluid flow and heat transfer have been discussed. Researchers have indicated that the effectiveness of the regenerative rotary heat exchanger depends on various factors including, among many others, rotational speed, rotational period and combustion power. It is reported that with the increase of periodic rotation the deviation of theoretical results from the experimental result increases. The available literature indicates that regenerative heat exchangers are having relatively more effectiveness (60-80%), compared to other heat exchangers. It is also observed that the finite difference method and finite volume methods are mostly used for discretizing the heat transfer governing equations, under some assumptions. Research also indicates that for the effectiveness calculation the ${\varepsilon}-NTU$ method is the most popular and convenient.

• Korean Journal of Materials Research
• /
• v.23 no.5
• /
• pp.281-285
• /
• 2013

In the present work, ZnO nanofibers were applied to electrode materials for the detection of cholesterol. ZnO nanofibers were synthesized using the electrospinning technique with zinc acetate as a precursor. Electrospinning-synthesized ZnO nanofibers were uniformly distributed by properly controlling the electrospinning parameters. After the calcination treatment, nanofibers of pure ZnO phase were synthesized. Then, these fibers were successfully placed on Au-coated glass substrates by dispersion of ZnO nanofibers in ethanol, dropping, and drying, in sequence. Cholesterol oxidase was then immobilized onto the surface of the ZnO nanofibers. To enhance the immobilization, Nafion was additionally applied. The sensing performances of the fabricated ZnO nanofibers-based sensors were analyzed by cyclic voltammetry in terms of cholesterol concentration ranging from 100 to 400 mg/dl. In the I-V curves, measured by cyclic voltammetry, the ZnO nanofiber-based sensor showed a proportional current behavior with cholesterol concentrations in phosphate buffered saline solution. The sensitivity was measured and found to be $30.7nA/mM{\cdot}cm^2$, which is comparable to the values reported in the literature. After not only optimizing the shape of the ZnO nanofibers but also improving the adhesion nature between the ZnO nanofibers and the Au conducting layer, these fibers can be a good candidate for electrode materials in devices used to detect low concentrations of cholesterol in blood.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.159-159
• /
• 2011

Among the semiconductor ternary compounds in the I-III-$VI_2$ series, $CulnS_2$ ($CulnSe_2$) are one of the promising materials for photovoltaic applications because of the suitability of their electrical and optical properties. The $CuInS_2$ thin film is one of I-III-$VI_2$ type semiconductors, which crystallizes in the chalcopyrite structure. Its direct band gap of 1.5 eV, high absorption coefficient and environmental viewpoint that $CuInS_2$ does not contain any toxic constituents make it suitable for terrestrial photovoltaic applications. A variety of techniques have been applied to deposit $CuInS_2$ thin films, such as single/double source evaporation, coevaporation, rf sputtering, chemical vapor deposition and chemical spray pyrolysis. This is the first report that $CuInS_2$ thin films have been prepared by Aerosol Jet Deposition (AJD) technique which is a novel and attractive method because thin films with high deposition rate can be grown at very low cost. In this study, $CuInS_2$ thin films have been prepared by Aerosol Jet Deposition (AJD) method which employs a nozzle expansion. The mixed fluid is expanded through the nozzle into the chamber evacuated in a lower pressure to deposit $CuInS_2$ films on Mo coated glass substrate. In this AJD system, the characteristics of $CuInS_2$ films are dependent on various deposition parameters, such as compositional ratio of precursor solution, flow rate of carrier gas, stagnation pressure, substrate temperature, nozzle shape, nozzle size and chamber pressure, etc. In this report, $CuInS_2$ thin films are deposited using the deposition parameters such as the compositional ratio of the precursor solution and the substrate temperature. The deposited $CuInS_2$ thin films will be analyzed in terms of deposition rate, crystal structure, and optical properties.

• Journal of Powder Materials
• /
• v.22 no.6
• /
• pp.408-412
• /
• 2015

This study attempts to manufacture a Ni-Cr-Al-Y coating layer using a kinetic spray process and investigates the microstructure and physical properties of the manufactured layer. The Ni-22Cr-10Al-1Y (wt.%) composition powder is used, and it has a spherical shape with an average diameter of $23.7{\mu}m$. Cu plate is used as the substrate. Optical microscope, X-ray diffraction, scanning electron microscope and Vickers hardness test are carried out to characterize the macroscopic properties of the coating layer. Furthermore, the coating layer underwent vacuum heat treatment at temperatures of $400^{\circ}C$ and $600^{\circ}C$ for 1 hour to check the effect of heat treatment temperature on the properties. The manufactured coating layer is 1.5 mm thick, and featured identical phases to those found in the powder. The porosity of the coating layer is measured at 2.99%, and the hardness is obtained at $490.57H_v$. The layer shows reduced porosity as heat treatment temperature increased, and hardness is reduced at $400^{\circ}C$ but shows a slight increase at $600^{\circ}C$. Based on the findings described above, this study also discusses possible manufacturing methods for a Ni-Cr-Al-Y coating layer using the kinetic spray process.

• Journal of Fashion Business
• /
• v.20 no.5
• /
• pp.60-75
• /
• 2016

This research was conducted to understand the different circumstances for wearing shirts by adult males aged 20-39, and to provide this basic information to the shirt industry prior to developing new functional men's shirts. A total of 345 respondents participated in the survey. Most of questionnaire, frequency, mean and standard deviation were calculated and the differences between the 20s and 30s were analyzed by t-test or ${\chi}^2$ test. The results of the survey are as follows. Grading the satisfaction degree of their body parts, the respondents were relatively unsatisfied with their height, weight, and waist, abdominal and hip circumferences. Majority preferred department stores, discount stores and outlets for purchasing shirts. Many have never owned tailored shirts - men in 20's had less experience with tailoring than men in 30's. The foremost selection criterion for purchasing shirts was fit -during purchase, men in their 20's considered fit more important than men in their 30's. The most preferred unbuttoning of the top button when wearing shirts. For favored collar shapes with one button unbuttoned, the most valued collar angle and style was V-neck shape when unbuttoned, low collar band, collar with unopened collar, and stiff collars. Most shirt designs and details included slim fit, no dart in the front and one dart on the back. Men in 20's more preferred the no dart in the front and one tuck on the back, as compared to men in 30's. On the other hand, men in their 30's preferred one dart shirts than men in 20's. Regarding shirt bands and cuffs, one button and regular collar and one button cuffs with round angle design, were the most preferred, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.132-132
• /
• 2018

NiTi 형상 기억 합금은 형상기억 효과 (Shape memory effect) 또는 초탄성 효과 (superelasticity effect)를 나타낸다고 알려져 있다. 대표적으로 Ni:Ti 조성비가 1:1을 갖는 NiTi(니티놀) 합금은 형상기억 및 초탄성 효과가 우수하여 기계 가공 공정뿐만 아니라 우수한 내마모성을 요구하는 공구에 사용하기 적합하다. 하지만 NiTi 박막은 합금과 같은 Damping capacity를 가지고 있지만 비교적 낮은 물리적 특성을 가지고 있다. 본 연구에서는 NiTi 박막의 낮은 물리적 특성을 향상시키기 위하여 TiN과 NiTi의 2층형 박막을 제조하고 각 층의 두께 변화를 조절하여 특성 향상에 대한 기초연구를 진행했다. 타겟은 NiTi (Ni:Ti=48.2:51.8 at.%) 합금 타겟과 Ti 타겟을 사용하였고, 시편과 타겟 간의 거리는 약 10cm 이며, 시편은 기초분석을 위한 SUS304, 물리적 특성 평가를 위한 초경 을 사용하였다. 초경은 실제 공구에서 사용하고 있는 Co함량이 10% 함유된 시편은 선정했다. 시편 전처리는 알코올과 아세톤으로 세척을 실시한 후 진공챔버에 장착하고 ${\sim}10^{-5}Torr$ 까지 진공배기를 실시하였다. 기판 정청은 글로우 방전 방식으로 약 800 V 전압에서 30분간 실시했다. 공정 가스는 Ar와 $N_2$ 혼합가스를 사용하였으며, UBM(Un-Balanced Magnetron) 스퍼터링 소스를 이용하여 2층형 박막을 제조했다. TiN과 NiTi 층의 두께 비율을 0.5, 1 그리고 2 로 변화시켜 코팅했으며, 박막의 총 두께는 약 ${\sim}3{\mu}m$ 이다. 기초분석은 FE-SEM을 통해 두께와 박막 비율을 확인 및 XRD 분석을 통해 박막 정성분성을 실시했다. 2층형 박막의 물리적 특성은 Nanoindentation test, AFM 및 ball on disc를 이용하여 평가했으며, 그 결과 두께 비율 변화에 따라 물리적 특성 변화가 나타남을 확인했다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.10
• /
• pp.2217-2222
• /
• 2011

In this paper, the relationship of potential and charge distribution in channel for double gate(DG) MOSFET has been derived from Poisson's equation using Gaussian function. The relationship of subthreshold swing and oxide thickness has been investigated according to variables of doping distribution using Gaussian function, i.e. projected range and standard projected deviation, The analytical potential distribution model has been derived from Poisson's equation, and subthreshold swing has been obtained from this model for the change of oxide thickness. The subthreshold swing has been defined as the derivative of gate voltage to drain current and is theoretically minimum of 60 mS/dec, and very important factor in digital application. Those results of this potential model are compared with those of numerical simulation to verify this model. As a result, since potential model presented in this paper is good agreement with numerical model, the relationship of subthreshold swing and oxide thickness have been analyzed according to the shape of doping distribution.

• Journal of Sensor Science and Technology
• /
• v.23 no.2
• /
• pp.114-121
• /
• 2014

We report a polysilicon active area membrane field effect transistor (PSAFET) pressure sensor for low stress deflection of membrane. The PSAFET was produced in conventional FET semiconductor fabrication and backside wet etching. The PSAFET located at the front side measured pressure change using 300 nm thin-nitride membrane when a membrane was slightly strained by the small deflection of membrane shape from backside with any physical force. The PSAFET showed high sensitivity around threshold voltage, because threshold voltage variation was composed of fractional function form in sensitivity equation of current variation. When gate voltage was biased close to threshold voltage, a fractional function form had infinite value at $V_{tn}$, which increased the current variation of sensitivity. Threshold voltage effect was dominant right after the PSAFET was turned on. Narrow transistor channel established by small current flow was choked because electron could barely cross drain-source electrodes. When gate voltage was far from threshold voltage, threshold voltage effect converged to zero in fractional form of threshold voltage variations and drain current change was mostly determined by mobility changes. As the PSAFET fabrication was compatible with a polysilicon FET in CMOS fabrication, it could be adapted in low pressure sensor and bio molecular sensor.