Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.23
no.8
/
pp.655-659
/
2010
Nanoporous titanium dioxide ($TiO_2$) is very attractive material for various applications due to the high surface to volume ratio. In this study, we have fabricated nanoporous $TiO_2$ thin films on Si by anodic oxidation. 500-nm-thick titanium (Ti) films were deposited on Si by using electron beam evaporation. Nanoporous structures in the Ti films were obtained by anodic oxidization using ethylene glycol electrolytes containing 0.3 wt% $NH_4F$ and 2 vol% $H_2O$ under an applied bias of 5 V. The diameter of nanopores in the Ti films linearly increased with anodization time and the whole Ti layer could become nanoporous after anodizing for 3 hours, resulting in vertically aligned nanotubes with the length of 200~300 nm and the diameter of 50~80 nm. Upon annealing at $600^{\circ}C$ in air, the anodized Ti films were fully crystallized to $TiO_2$ of rutile and anatase phases. We believe that our method to fabricate nanoporous $TiO_2$ films on Si is promising for applications to thin-film gas sensors and thin-film photovoltaics.
This paper describes a low-voltage and low-power channel selection analog front end with continuous-time low pass filters and highly linear programmable-gain amplifier(PGA). The filters were realized as balanced Gm-C biquadratic filters to achieve a low current consumption. High linearity and a constant wide bandwidth are achieved by using a new transconductance(Gm) cell. The PGA has a voltage gain varying from 0 to 65dB, while maintaining a constant bandwidth. A filter tuning circuit that requires an accurate time base but no external components is presented. With a 1-Vrms differential input and output, the filter achieves -85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA were implemented in a 0.18um 1P6M n-well CMOS process. They consume 3.2mW from a 1.8V power supply and occupy an area of $0.19mm^2$.
Proceedings of the Korean Vacuum Society Conference
/
2016.02a
/
pp.165.1-165.1
/
2016
Zn의 수요는 매년 증가하지만 매장량의 한계로 대체용 물질계가 개발이 필요한 시점이다. Zn보다 상대적으로 풍부하고 동일 두께의 Zn 코팅층과 비교하여 우수한 내식성을 보이는 Al과 Mg의 코팅층을 제작하여 Al-Mg 코팅 강판의 특성 분석 및 평가를 실시하였다. Al-Mg 코팅층은 99.99%의 Al, 99.9%의 Mg target을 사용하여 스퍼터링을 이용하여 냉연강판 위에 코팅하였다. 증발물질과 기판과의 거리는 7cm 이며, 기판은 세척을 실시한 후 클리닝 챔버에 장착하고 ~10-5 Torr 까지 진공배기를 실시하였다. 클리닝 챔버가 기본 압력까지 배기되면 아르곤 가스를 주입하고 기판 홀더에 -800 V의 직류 전압을 인가하여 약 30분간 글로우 방전 청정을 실시하였다. 기판의 청정이 끝나면 아르곤 가스를 차단하고 코팅 챔버로 시편을 이송 후 코팅층 성분의 구성형태에 따라 Al과 Mg을 코팅하였다. Al-Mg 코팅층은 $3{\mu}m$의 두께를 기준으로 Mg wt.%의 비율을 5% ~ 90%까지 변화시키며 코팅하였다. 그리고 후속 공정으로 질소 분위기 $400^{\circ}C$에서 10분간 열처리를 하였다. Al-Mg 코팅층을 주사전자현미경으로 관찰한 결과, 표면에서는 Al-Mg 코팅층에 존재하는 Mg 함량이 높아질수록 grain의 크기가 증가하였고 단면에서는 열처리 전의 치밀한 구조에서 열처리 후에는 주상구조 혹은 grain 구조가 선명해지는 것을 볼 수 있었으며 글로우방전분광기로 Al과 Mg의 성분 비율변화를 확인할 수 있었다. 또한 Al-Mg가 코팅된 강판을 염수분무시험을 통해서 내부식 특성을 확인하였다. Al-Mg 코팅 강판의 염수분무시험 결과, Mg 함량이 낮은 Al-Mg 코팅층은 열처리 후 뚜렷한 내식성 향상을 보였으며 Mg 조성 변화에 따라 일정한 경향성을 보였다. 하지만 Mg 함량이 높은 Al-Mg 코팅층은 열처리 후 급격한 내식성 저하와 함께 시편간의 편자가 커지는 것을 확인 할 수 있었다. 최적의 내식성을 보이는 Mg의 조성을 확인하기 위해서는 향후 보다 변별력이 높은 평가가 결과가 필요하다고 판단되어진다.
This is a report on the recovery of vegetation and secondary succession in the burned area studied from April, 1990 to April. 1991. The forest fire occurred in a part of Mt. $K\v{u}mo-san$ on April, 1986 and the pine forest and its understory vegetation were burned out completely. The floristic compositions of burned (B) and unburned (U) areas were composed of sixty eight and thirty one species (vascular plants), respectively. These species were divided into invaders (47 species), increasers (15 species), deceasers (3 species), neutrals (3 species), and retreaters (10 species) on the basis of summed dominance ratio ($SDR_3$). Biological spectra showed the $H-D_1-R_5-e$ type in both the burned and unburned areas. The species of Lespedeza ($SDR_3$=94.7), Miscanthus (91.95), Festuca (68.33), and Spodiopogon (52.06) were dominant in the burned areas, while the species of Pinus (76.67), Robinia (56.25), Quercus (52.08), and Carex (40.25)were dominant in the unburned area. Dominance index (C) in burned and unburned areas was 0.15 and 0.25, respectively. the index of similarity (CCs) was 0.42. The degree of succession (DS) and species diversity (H) in burned and unburned areas were 675.8, 884.2 and 4.07, 2.05, respectively. The degree of succession in the burned area graduall increased and the burned area was recovered to be simmilar to the unburned area. Evenness index in burned and unburned areas was 0.965 and 0.595, respectively.
Asymetric system have been introduced in these years by KODAK company nam of Insight system for the purpose of improve the chest image. We have had a problem of chest radiology that it is very difficult to visualize the lung field and modiastinal region at one shot. That's why we are the RT using the technique of high voltage hard quality radiography in chest radiography. Also it is known the c-type wide latitude film can lift up the density of mediastinal structures. Authors investigated the photographic characteristics and physical structure of Insight system. Method 1. Investigated the structure of Emulsion layer. Calculated the particle size of Insight system using SEM(Scanning Electron Microscope). 2. Photographic characteristics has been compared the Insight system with the ortho KM/MG combination in $60{\sim}120kV$ range. Results 1. The particle size of backside film were investigated about 2 times larger that of front side film. 2. The front and backscreen's thickness ratio was detected 1 : 3.87, that the backscreen's thickness was thicker than frontscreen. 3. At the view point of photographic characteristics the frontside of insight system make up the contrast, backside make up the density at low exposure lesion.
Monolayer graphene grown via chemical vapor deposition (CVD) is recognized as a promising material for sensor applications owing to its extremely large surface-to-volume ratio and outstanding electrical properties, as well as the fact that it can be easily transferred onto arbitrary substrates on a large-scale. However, the Dirac voltage of CVD-graphene devices fabricated with transferred graphene layers typically exhibit positive shifts arising from transfer and photolithography residues on the graphene surface. Furthermore, the Dirac voltage is dependent on the channel lengths because of the effect of metal-graphene contacts. Thus, large and nonuniform Dirac voltage of the transferred graphene is a critical issue in the fabrication of graphene-based sensor devices. In this work, we propose a fabrication process for graphene field-effect transistors with Dirac voltages close to zero. A vacuum annealing process at $300^{\circ}C$ was performed to eliminate the positive shift and channel-length-dependence of the Dirac voltage. In addition, the annealing process improved the carrier mobility of electrons and holes significantly by removing the residues on the graphene layer and reducing the effect of metal-graphene contacts. Uniform and close to zero Dirac voltage is crucial for the uniformity and low-power/voltage operation for sensor applications. Thus, the current study is expected to contribute significantly to the development of graphene-based practical sensor devices.
The influence of fungicidal spray was assessed on powdery mildew epidemics caused by Erysiphe polygoni D.C. and on yield-attributing characters of mungbean [Vigna radiata (L.) Wilczek]. Mildew attack adversely affected the yield-attributing characters of mungbean and exhibited negative significant correlation with pod length (-0.57), pods/plant (-0.74), pod weight (-0.68), 100 seeds weight (-0.69), 100 seeds swell weight (-0.59), and seed germination (-0.71). These characters had direct or indirect effects on grain yield, which was also adversely affected due to mildew attack (-0.89). Powdery mildew was significantly retarded due to the single spray of carbendazim (0.05%) at 30-day-old crop, where the apparent rate of infection (r) was minimum at 0.0095/ unit/day and with low (11.44%) powdery mildew intensity. Other fungicides like tridemorph (0.075%) and penconazole (0.05%) were equally effective against the mildew disease where the disease intensity was less than 20% and the values of r were 0.0134 and 0.039/unit/day respectively, as compared with the control at 0.267/unit/day. Fungicide spray influenced the yield-attributing characters besides controlling the disease. Such effects were more pronounced in carbendazim (0.05%)-treated plots due to its phytotonic nature where pod length (7.59cm), pods/plant (29.75), pod weight (8.16 g), 100 grain weight (3.94 g), and swell weight of 100 seed (9.49 g) were maximum resulting to the highest yield (480 kg/ha) as compared with that of control (224 kg/ha). Spray of carbendazim also improved seed germination (74.5%). Spray of other fungicides like carbendazim with copper oxychloride in 1:1 ratio, tridemorph (0.075%), and penconazole (0.05%) was equally effective against powdery mildew of mungbean. These fungicides also exhibited positive effects on yield-attributing characters of the crop and finally increased yield. These systemic fungicides were more effective in controlling powdery mildew disease of V. radiata in the rainy season compared with wettable sulphur.
CHA, Jong Whan (Dept. of Biology, College of Education, Seoul National University). Effect of gibberallin on the growth and internal componsents of Astragalus sinicus L. Kor. Jour. Bot. V(4) : 1-5, 1962. The effect of GA on the growth as well as on the internal components of the leaves of Astragalus sinicus L. under the soil culture was investigated. The result has indicated that small variation in the relative concentration of GA treated on the leaves shows a marked influence on the internal components of the plants. The increase of growth was associated with increasing intensity of GA. Chlorophyll and carotene contents in the leaves were depressed with increasing concentration of GA. It was noticed that the growth was pomoted with the decrease of the contents of chlorophyll and carotene. In contrast the aacorbic acid in the leaves treated with GA decreased in proportion to the degree of the concentration of GA. Carotens content varied with chlorophyll, although the ratio of chlorophyll to carotene was not so high as the results obtained by Beck and Redman. Chlorophyll and ascorbic acid values with respect to growth differed greatly during the two experimental periods. The chlorophyll content was found highly significant in this experimental periods. The chlorophyll content was found highly significant in this experiment. As the concentration of GA was increased, it was noticed that there was a reduction of anthocyanin, sucrose, and reducing sugar contents. The anthocyanin content was not so high in this study as in the results obtained from the corn by Jacob Straus.
This study was performed to evaluate accuracy and precision of filter method and impinger method for analyzin airborne isocyanates in mixture (2, 6-TDI, HDI, 2, 4-TDI, MDI). Filter method was performed using the OSHA Method 42 and impinger method using the NIOSH Method 5521. The samples were analyzed by high performance liquid chromatography-ultraviolet detector (HPLC-UVD). After the optimum operating conditions for each method were investigated, samples with various concentration levels were quantified at the conditions. The precision was expressed by the pooled coefficient of variation(C.V.) and the accuracy by overall accuracy. The results are summarized as follows: 1. The optimum condition of filter method was determined at 35/65 ACN/buffer (0.01 M ammonium acetate) in mobile phase. And in case of impinger method, it was at 30/70 ACN/buffer(0.2 M sodium acetate). The effect of concentrations of acetate on the separation of the peaks was not significant, but, the effect of ACN/buffer ratio was significant. 2. The correlation coefficients for the two methods were above 0.9 in all isocyanate compounds. Average recovery efficiencies for 2, 6-TDI, HDI, 2, 4-TDI and MDI in filter method were 92.4%, 102.6%, 87.3% and 101.0%, respectively. Those in impinger method were 106.6%, 106.7%, 99.0% and 103.6%, respectively. As a result, the recovery efficiency of impinger method was higher than those of filter method in analyzing isocyanate compounds. 3. The pooled coefficients of variations of the methods were slightly higher than expected. The overall accuracies of the methods were within $\pm 25%$ for each isocyanate compound. Since these results satisfy NIOSH criteria, the accuracy of the experiment is appropriate. 4. As seen above, impinger method is more efficient than filter method. But, there are many disadvantages in impinger method. Therefore, solid sorbent such as a glass fiber filter must be developed in order to have the high efficiency not less than that of impinger method in the future.
In this study several kinds of spun silk yarn-synthetic filament compounded yarn was manufactured, and several fabrics woven from above mentioned silk compound yarn for evaluation of serviceability as clothing materials. The following results were obtained: 1. Degumming agents are in the order of sodium silicate, sodium hydroxide, sodium carbornate, soap and water. 2. When the concentration of sodium hydroxide is exceeded 3%, degradation of floss silk property is resulted because of excessive dissolving out of silk protein. 3. Degumming effect is much improved by concentration of degumming agent and less by its treating time. 4. Simultaneous application of more the 2 kinds of degumming agent is desirable for improvement of floss silk. 5. Application of natural organic acid brings very good results in keeping original scooping and color of the silk. 6. Load and elongation it increased by compound with synthetic filament yarn. 7. Even the evenness of compound yarn is largely dependent on the quality of floss silk and extent of degumming, the C.V.% of silk compound yarn in the experiment was 8-12%. 8. Single bath dyeing technique was impossible for their cloth, and dyeing was performed in 2 bath system separately for silk and synthetic fiber. 9. Shrinkage ratio due to the dyeing of fabric was 23% in case of polyester and spun silk fabric. 10. The final woven cloth can be applicable to (a) Blouse in care of thin cloth (compound silk fabric) (b) Korean costume for women in case of thick cloth. (compound hand spun silk fabric)
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.