• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.9-14
• /
• 2003

The new optical link receiver with data transfer rate higher than 10Mbps at the supply voltage of 1.8V was designed and fabricated using bipolar technology. The fabricated IC showed the dissipation current of 4.6mA under high level input voltage of 1.5V. The high level output voltage($V_{OH}$) and the low level output voltage($V_{OL}$) were 1.15V and 0V, respectively, for a given 10 Mbps signal which has duty ratio of 50%, $V_{IL}$(low level input voltage) of 0.5V, and $V_{IH}$(high level input voltage) of 1.5V, The duty ratio of output waveform was 52.6%. The rising time(t$_{r}$) and the falling time(t$_{f}$) were 9.5ns and 6.8ns, respectively. The propagation delay difference($t_{PHC}-t_{PLH}$) and the jitter($t_j$) were 11.7ns and 4.3ns, respectively.y.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.5
• /
• pp.494-498
• /
• 2022

In this study, SiO₂ 20 phr, ATH 70 phr, and platinum flame retardant were mixed with raw silicone rubber and -10 kV was applied to measure electrostatic charge attenuation voltage, surface resistance, and volume resistance, and the following conclusions were obtained. When the platinum flame retardant was 0 phr, the humidity 74.6% and the temperature was 21.8℃, the potential was half-reduced to 0.63 kV, 0.57 kV, and 0.44 kV when the applied voltage was changed from -10 kV to -8 kV, and the time halved to 50% was increased to 2.40 seconds, 2.47 seconds, and 2.61 seconds. It was confirmed that as the platinum flame retardant increased from 0.1 to 0.3 phr, the potential half-reduced to 0.67 kV, 0.60 kV, and 0.595 kV decreased, and the charge potential attenuation time half-reduced to 50% decreased to 3.44 seconds, 1.78 seconds, and 1.60 seconds. It was confirmed that the surface resistance increased as the humidity decreased, and the volume resistance decreased as the platinum flame retardant increased.

• Horticultural Science & Technology
• /
• v.34 no.5
• /
• pp.727-735
• /
• 2016

This research was conducted to investigate the influence of various pre-planting $NO_3:NH_4$ ratios in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium on the growth of tomato plug seedlings (cv. Dotaerang Dia), changes in chemical properties of root media, and tissue nutrient contents. With the fixation of N concentration to $300mg{\cdot}L^{-1}$, the $NO_3:NH_4$ ratios were adjusted to 100:0, 73:27, 50:50, 27:73, 0:100. Then, root media containing various $NO_3:NH_4$ ratios and equal concentration of other essential nutrients were filled into 50-cell plug trays and the seeds of 'Dotaerang Die' tomato were sown. The investigation of seedling growth and tissue analysis for mineral nutrient contents based on the dry weight of above-ground tissue were conducted 6 weeks after sowing. As seedlings grew, the EC decreased quickly and pH increased gradually in the all treatment media. The plant height, fresh weight and dry weight of seedlings in the treatment of 50:50 ($NO_3:NH_4$) were 29.0 cm, 13.7 g, and 1.21 g, respectively, which were the highest among treatments tested. However, the seedlings in the treatment of 0:100 ($NO_3:NH_4$) had 26.5 cm, 11.2 g, and 0.92 g in plant height, fresh weight and dry weight, respectively. These were the poorest among the treatments tested. The tissue contents of N were 2.77 to 3.22% in all the treatments. The treatment of 27:73 ($NO_3:NH_4$) had the highest contents of Fe, Mn and Zn and that of 0:100 ($NO_3:NH_4$) had the lowest contents of Mg, Na, Cu, Mn and Zn among the treatments tested. The results indicate that $NH_4$ ratio should be lower than 50% in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium for seedling growth of tomato and the optimum ratio will be used to draw up guide lines for plug seedling production.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.8
• /
• pp.522-527
• /
• 2014

In this study, using the silicone rubber sample of $4cm{\times}4cm{\times}0.1cm$ for low voltage cable, the electrostatic electrification properties of three samples that the conductive Al of 0%, 25%, and 50% is attached to the surface of sample was measured. The following conclusion was obtained through this experiment. 1) In case of the sample which has the Al area of 50%, the higher the humidity to 90% in the temperature of $10^{\circ}C$, the electrostatic electrification voltage was reduced about 0.25 kV to 0.02 kV, and it confirmed that the electrostatic electrification voltage was in constant about 0.02 kV in the temperature over $20^{\circ}C$. 2) Increasing the Al area of samples of 0%, 25%, and 50% in temperature of $10^{\circ}C$, it confirmed that the electrostatic electrification voltage was reduced by about 2.67 kV, 2.02 k, 0.21 kV. 3) This study shows that the conductor, followed by temperature and humidity affects the electrostatic electrification voltage.

• Journal of Astronomy and Space Sciences
• /
• v.33 no.4
• /
• pp.247-256
• /
• 2016

An analysis of light curves and spectra of observed gamma-ray bursts in gamma-ray ranges is frequently demanded because the prompt emission contains immediate details regarding the central engine of gamma-ray bursts (GRBs). We have revisited the relationship between the collimation-corrected peak luminosity and the spectral lag, investigating the lag-luminosity relationships in great detail by focusing on spectral lags resulting from all possible combinations of channels. Firstly, we compiled the opening angle data and demonstrated that the distribution of opening angles of 205 long GRBs is represented by a double Gaussian function having maxima at ~ 0.1 and ~ 0.3 radians. We confirmed that the peak luminosity and the spectral lag are anti-correlated, both in the observer frame and in the source frame. We found that, in agreement with our previous conclusion, the correlation coefficient improves significantly in the source frame. It should be noted that spectral lags involving channel 2 (25-50 keV) yield high correlation coefficients, where Swift/Burst Alert Telescope (BAT) has four energy channels (channel 1: 15-25 keV, channel 2: 25-50 keV, channel 3: 50-100 keV, channel 4: 100-200 keV). We also found that peak luminosity is positively correlated with peak energy.

• Journal of Chest Surgery
• /
• v.25 no.4
• /
• pp.364-382
• /
• 1992

In order to investigate the effect of intracellular cyclic GMP on the calcium channel, whole cell patch clamp technique with internal perfusion method was used in the single ventricular myocytes of the rabbit. Cyclic GMP, cGMP analogues, cAMP, isopernaline and forskolin were perfused into cells and their effects on the calcium current were analysed by applying depolarizing step pulse of 10 mV in amplitude for 200 msec from holding potential of -40 mV. Calcium currents usually activated from -30 mV and then reached a peak at +10 mV. Amplitude of the calcium current was standardized with membrane capacitance, 50 pF. Peak amplitude at +10 mV in control was -0.15 nA/50pF. When 100 mM cAMP was applied from the pipette, peak amplitude of calcium current increased to -0.32 nA and addition of 1 mM isoprenaline further increased its amplitude. In the presence of cGMP it alone also produced an increase of the calcium current to -0.52 nA/50pF and addition of isoprenaline or forskolin increased its magnitude to -[0.55~0.95] nA/50pF. Simultaneous application of cGMP and cAMP increased the calcium current to -0.67 nA/50pF. Among the cGMP analogues, 8-Br-cGMP was the most potent stimulant for the calcium current activation. From the above results it could be concluded tlat cGMP increases the calcium current not through cAMP dependent protein kinase nor cAMP dependent phosphodiesterase pathway, but through independent phosphorylation pathway, possibly cGMP dependent protein kinase pathway.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 1997.10a
• /
• pp.58-58
• /
• 1997

The corrosion rate of polymer polyethylene terephtalate and polyvinylchloride was characterized at various condition by potentiostate / galvanostate method. The cell and working electrode used for this study was specially preparatain, The potential was scanned at foward scan -2V to 3V and reward scan 3V to -2V, at 50mv/s (R: auto - compensation).

• Journal of radiological science and technology
• /
• v.33 no.3
• /
• pp.179-184
• /
• 2010

A hard X-ray microscope system for obtaining images of nano-spatial resolution has been widely studied and requires monochromatic X-ray. A multilayer mirror of 84% reflectivity was designed to acquire tungsten characteristic X-ray of 8.4 keV from the white beam generated from an X-ray tube, and the C/W multilayer mirror of $50{\times}50\;mm$ size and 5.65 nm d-spacing was fabricated by the ion-beam sputtering system. The C/W multilayer had a uniformity of 99.5%, and the structure of the multilayer mirror was verified by a TEM image. The obtainable x-ray reflectivity for the C/W multilayer mirror at 8.4 keV was estimated from measuring the X-ray reflectivity using the copper characteristic X-ray of 8.05 keV. Monochromatic X-ray of 8.4 keV was generated by combining a X-ray tube, and the reflectivity and monochromaticity were 77.1% and 0.21 keV, respectively. Monochromatic X-ray generated from the combination of an X-ray tube and an C/W multilayer mirror has enough potential to use X-ray source for hard X-ray microscope system of laboratory size. If the C/W multilayer mirror of d-spacing of a few nanometers can be fabricated, monochromatic X-ray corresponded to 17.5 keV, molybdenum characteristic X-ray, can be obtained and applied to mammography in the medical application.

• The Korean Journal of Mycology
• /
• v.40 no.1
• /
• pp.49-53
• /
• 2012

Hot-water extracted natural media were made from raw materials for mycelial culture of Pleurotus eryngii. Poplar sawdust, wheat bran and rice bran were used as substrates for hot water extraction. The mixed substrates of poplar sawdust, wheat bran, and rice bran with 50 : 20 : 30 (v/v/v, PWR523) and 50 : 30 : 20 (v/v/v, PWR532) were optimal for mycelial growth of P. eryngii, respectively. The hot-water extracted natural media from PWR523 and PWR532 showed a rapid mycelial growth and spawn running compared to PDA. There was no significant difference in mushroom yield when the mycelium grown on the hot-water extracted natural media was used as the inoculum source for producing fruit body.

• Applied Chemistry for Engineering
• /
• v.31 no.2
• /
• pp.179-186
• /
• 2020

In this study, chitosan/zeolite composites were prepared by using basalt-based zeolite impregnated with aqueous chitosan solution for the adsorptive separation of CO₂. The prepared composites were characterized by scanning electron microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption analysis. In addition, the adsorption equilibrium isotherms for CO₂ and N₂ were measured at 298 K using a volumetric adsorption system, and the results were analyzed by applying adsorption isotherm equations (Langmuir, Freundlich, and Sips) and energy distribution function. It was found that CO₂ adsorption capacities were well correlated with the structural characteristics of chitosan and zeolite, and the ratio of elements [N/C, Al/(Si + Al)] formed on the surface of the composite. Moreover, the CO₂/N₂ adsorption selectivity was calculated under the mixture conditions of 15 V : 85 V, 50 V : 50 V, and 85 V : 15 V using the Langmuir equation and the ideal adsorption solution theory (IAST).