• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.237-247
• /
• 1993

Activity ratio of two radioactive primary fission products which had sufficiently different half-lives was expressed as functions of cooling time and irradiation histories in which average burnup, irradiation time, cycle interval time and the dominant fissile material of the spent fuel were included. The gamma-ray spectra of 36 samples from 6 spent PWR fuel assemblies irradiated in Kori unit-1 reactor were obtained by a spectrometric system equipped with a high purity germanium gamma-ray detector. Activity ratio $^{l44}$Ce $^{l37}$Cs, analyzed from each spectrum, was used for the calculation of cooling time. The results show that the radioactive fission products $^{l44}$Ce and $^{l37}$Cs are considered as useful monitors for cooling time determination because the estimated cooling time by detection of activity ratio $^{l44}$Ce $^{l37}$Cs agreed well with the operator declared cooling time within relative difference of $\pm$5 % despite the low counting rate of the gamma-ray of $^{l44}$Ce (about 10$^{-3}$ count per second). For the samples with several different irradiation histories, the determined cooling time by modeled irradiation history showed good agreement with that by known irradiation history within time difference of $\pm$0.5 year. From this result, it would be expected to be possible to estimate reliably the cooling time of spent nuclear fuel without the exact information about irradiation history. The feasibility study on identification of and/or sorting out spent nuclear fuel by applying the technique for cooling time determination was also performed and the result shows that the detection of activity ratio $^{l44}$Ce $^{l37}$Cs by gamma-ray spectrometry would be usefully applicable to certify spent nuclear fuel for the purpose of safeguards and management in a facility in which the samples dismantled or cut from spent fuel assemblies are treated, such as the post irradiation examination facility.mination facility.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.301-309
• /
• 2017

This study was conducted to provide basic data needed to calculate the crop loads for the greenhouse design. Four countries' crop loads for greenhouse structures were compared and the crop loads were measured directly and analyzed for various greenhouse crops, including tomato, strawberry, cucumber, and eggplant. According to the analysis results of four country's standards for the design crop loads, it was judged that the new design crop loads suit for greenhouse crops in our country should be suggested because our standards just used the design crop loads of other countries. The maximum crop loads per plant of tomato, cucumber, eggplant, and strawberry were 3.9, 0.75, 1.9 and $2.1kgf{\cdot}plant^{-1}$, respectively. The crop load per unit area of tomato was $8.5kgf{\cdot}m^{-2}$, which was much greater than the cucumber and eggplant's crop load of 2.1 and $2.4kgf{\cdot}m^{-2}$ respectively. The crop loads of tomato and cucumber, suggested by the greenhouse structure design standard of Korea, is $15kgf{\cdot}m^{-2}$, which is far greater than the values suggested by this research. It was judged that this was because our standard just used the Dutch standard, our crop load standard should be reviewed considering this difference. The crop load of strawberry, including the growing bed, was $21.0kgf{\cdot}m^{-2}$, which was much greater than the crop load in the Dutch standard.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.6
• /
• pp.405-415
• /
• 2000

To determine application rate of elemental sulfur to adjust pH of alkaline soil, buffer curve method was investigated. The elemental sulfur required to control pH 8.3 to pH 6.3 by buffer curve calculation was treated in two soils of silty loam and sandy loam, and the sulfur-mixed soils were moistened with 50% of water holding capacity during incubation of 6 weeks at $30^{\circ}C$. Soil pH was lowered with incubation and reached to target point after 4 weeks of incubation, and elemental sulfur was oxidised entirely to sulfate. This means that buffer curve has the accuracy to determine sulfur application rate in alkaline soil. However it is estimated that application rate of sulfur should be carefully determined in the field scale. Excess application of elemental sulfur resulted in extremely low soil pH and caused the hinderance of lettuce growth by nutritional imbalance and ion toxicity. To simplify the determination procedure of sulfur requirement, buffer curve method by addition of 0.1N-HCl solution as unit of mL was developed, it was compared with theroutine methods which diluted $H_2SO_4$ solution and $Ca(OH)_2$ are added as cmolc per kg soil to adjust each pH step. Buffer capacities, cmolc kg $soil^{-1}$ $pH^{-1}$, calculated from two buffer curves were not significantly different. The result indicates that buffer curve method by 0.1N-HCl can be used to adjust high pH of alkaline soil.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.2
• /
• pp.225-231
• /
• 2020

Fresh water that can be used by a person of the total amount of water on the planet is increased because it is less than 0.01 % except underground water, ice and snow, etc. water management response need. In order to protect and efficiently utilize water resources, major countries are conducting water footprint studies that can quantitatively estimate the amount of water put into the operating phase of the resource harvesting phase, mainly agriculture. Korea has also recently developed a number of policies in order to cope with water shortages, and in the construction industry, as well as the need for basic research to support it has been emphasized. This study was constructed DB up to the raw material harvesting step, the transport step, the production stage in order to estimate the water consumption of resources to be put into the work process to target the drainage of the road. Water usage estimation method was utilized the method presented in the Water Footprint Manual and the environmental score card certification guide, unit water usage each drainage main method was calculated after estimating the water footprint considering the water character factor, indirect water and the direct water, the water consumption factor of material input to each process. Brown asphalt, rebar, remicon of the drainage material as a result of the water footprint calculation accounted for 97 % of the total. Drainage method is a culvert, a side channel, a culvert wing wall, reinforced concrete open channel accounted for 92.2 % of the total. Drainage total step-by-step calculated water consumption and water footprint was found in order of raw material harvesting step, transport stage, production stage. Water footprint each drainage method or total drainage material calculated in this study can be used as a base data in the agricultural and construction sectors. In order to increase the reliability of the analysis, it is believed that further overseas databases will be needed for continuous review and research.

• Radiation Oncology Journal
• /
• v.14 no.3
• /
• pp.237-244
• /
• 1996

Purpose : The accurate dosimetry of independent collimator equipped for 6MV and 15MV X-ray beam was investigated to search for the optimal correction factor. Materials and Methods : The field size factors, beam quality and dose distribution were measured by using 6MV, 15MV X-ray Field size factors were measured from $3{\times}3cm^2$ to $35{\times}35cm^2$ by using 0.6cc ion chamber (NE 2571) at Dmax. Beam qualities were measured at different field sizes, off-axis distances and depths. Isodose distributions at different off-axis distance using $10\times10cm^2$ field were also investigated and compared with symmetric field. Result: 1) Relative field size factors was different along lateral distance with maximum changes in $3.1\%$ for 6MV and $5\%$ for 15MV. But the field size factors of asymmetric fields were identical to the modified central-axis values in symmetric field, which corrected by off-axis ratio at Dmax. 2) The HVL and PDD was decreased by increasing off-axis distance. PDD was also decreased by increasing depth For field size more than $5{\times}cm^2$ and depth less than 15cm, PDD of asymmetric field differs from that of symmetric one ($0.5\~2\%$ for 6MV and $0.4\~1.4\%$ for 15MV). 3) The measured isodose curves demonstrate divergence effects and reduced doses adjacent to the edge close to the flattening filter center was also observed. Conclusion . When asymmetric collimator is used, calculation of MU must be corrected with off-axis and PDD with a caution of underdose in central axis.

• Korean Journal of Remote Sensing
• /
• v.37 no.5_1
• /
• pp.903-916
• /
• 2021

An area's topography refers to the shape of the earth's surface, described by its elevation, slope, and aspect, among other features. The topographical conditions determine energy flowsthat move water and energy from higher to lower elevations, such as how much solar energy will be received and how much wind or rain will affect it. Another common factor, the topographic wetness index (TWI), is a calculation in digital elevation models of the tendency to accumulate water per slope and unit area, and is one of the most widely referenced hydrologic topographic factors, which helps explain the location of forest vegetation. Analyses of topographical factors can be calculated using a geographic information system (GIS) program based on digital elevation model (DEM) data. Recently, a large number of free open source software (FOSS) GIS programs are available and developed for researchers, industries, and governments. FOSS GIS programs provide opportunitiesfor flexible algorithms customized forspecific user needs. The majority of biodiversity in island areas exists at about 20% higher elevations than in land ecosystems, playing an important role in ecological processes and therefore of high ecological value. However, island areas are vulnerable to disturbances and damage, such as through climate change, environmental pollution, development, and human intervention, and lacks systematic investigation due to geographical limitations (e.g. remoteness; difficulty to access). More than 4,000 of Korea's islands are within a few hours of its coast, and 88% are uninhabited, with 52% of them forested. The forest ecosystems of islands have fewer encounters with human interaction than on land, and therefore most of the topographical conditions are formed naturally and affected more directly by weather conditions or the environment. Therefore, the analysis of forest topography in island areas can be done more precisely than on its land counterparts, and therefore has become a major focus of attention in Korea. This study is focused on calculating the performance of different topographical factors using FOSS GIS programs. The test area is the island forests in Korea's south and the DEM of the target area was processed with GRASS GIS and SAGA GIS. The final slopes and TWI maps were produced as comparisons of the differences between topographic factor calculations of each respective FOSS GIS program. Finally, the merits of each FOSS GIS program used to calculate the topographic factors is discussed.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.1
• /
• pp.39-48
• /
• 2019

Based on the bidding data of the national marketplace for public procurement service from 2003 to 2015, this study investigated and analyzed the bidding trends of the landscape management public consignment service by analyzing total bidding, type, client, region, license. The results are as follows. First, the total number of bids for civilian consignment services in landscape management increased by 1,112 cases, corresponding to a 487.7% increase over 10 years, and the total bidding amount increased by 144,504 million won, corresponding to a 382.5% increase. Second, in 10 years, the proportion of landscape management in landscaping works increased by 10%, and the bidding amount increased by 3%. Third, in the analysis of bidding trends by type, green areas showed the greatest growth in the number of bids, while the greenery of buildings showed the highest increase in the bid amount. Fourth, local autonomous entities, Gyeonggi province, and the landscaping planting construction industry showed the highest increase in the number of bids and the amount in each field such as client, region, and license. In summary, the number of cases and the bidding amount is increasing year by year. Considering the increasing number of users and demands thereof, the number of bids and the amount of consignment service for landscape management will continue to increase. The purpose of this study is to investigate and systematically analyze the tendency of bidding for 10 years for the private consignment service of landscape management in the current situation, where the importance of landscape management is increasingly emphasized. Another purpose of this study is to discern the necessity of the landscape management business and to provide the basis for incorporating the landscape management business into the professional construction industry in the future, thus providing opportunities for widening the expertise and diversity of the landscaping field. For the following study, the legal basis of landscape management, qualification, equipment standards, calculation of management cost per unit, and the appropriateness of the management cost should be considered.

• Korean Journal of Construction Engineering and Management
• /
• v.24 no.6
• /
• pp.24-35
• /
• 2023

Recently, the Ministry of Land, Infrastructure and Transport presented the '6th Construction Technology Promotion Basic Plan' and 'Smart Construction Revitalization Plan (2022.7.20)'. Off-Site Construction (OSC), which involves construction and production of PC (Precast Concrete) and Modular, etc., has advantages in shortening the construction period, reducing costs, improving quality, reducing construction waste, and reducing safety accidents. However, the construction cost is high compared to the traditional RC construction method, which has hindered its utilization and spread. In this study, OSC utilization was improved. An economic analysis indicator and methodology that can support decision-making in the planning and design stages for multi-unit housing were proposed. The factors used in the economic analysis of OSC (based on the PC method) of apartment houses were reviewed. As for the indicators used in the cost and benefit section, 'Construction Period', 'Disaster Occurrence', 'Waste Generation', and 'Greenhouse gas Emission', which reflect the technical advantages of OSC, were derived. In addition, a scenario analysis was conducted based on actual apartment housing case data for the presented economic analysis indicators and benefit calculation standards. The level of benefit that offsets the difference between the existing RC construction method and the construction cost was reviewed. In future studies, it will be necessary to conduct additional case studies to apply the measurement criteria for detailed indicators and supplement the benefit indicators.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.52 no.5
• /
• pp.27-41
• /
• 2024

The current method of calculating the carbon stocks of Korea's forests is to multiply the forest standing crop by basic wood density, biomass expansion factor, and carbon fraction, but it does not sufficiently reflect forest vegetation. This study attempted to present a method of calculating carbon stocks using the biotope map and Biomass Allometric Equations for forests in Suji-gu, Yongin City. The biotope map is prepared every five years and contains detailed information on vegetation, including the actual vegetation and land cover status. The forest biotope of Suji-gu was extracted from the Yongin City biotope map, and the tree species, height, and breast height diameter of 24 representative types of forest vegetation sampled in Yongin City were analyzed in detail. To calculate the carbon stocks of trees and shrubs, the Biomass Allometric Equations developed by the National Institute of Forest Science was used, and to calculate the carbon stocks of shrubs, the previous research result of 0.457 kg per m² was applied. First, carbon storage was calculated for each types of forest vegetation sampled in Yongin City, and in order to apply this to the entire area, the 125 forest vegetation types in Suji-gu, Yongin City were retyped into 50. As a result, the Quercus mongolica community occupied the largest area, followed by the Pinus rigida community, the Quercus acutissima community, and the Quercus serrata community. The community with the highest carbon stocks per unit area (m²) was the Cornus controversa-Quercus mongolica community, and the community with the lowest was the oak-Betula dahurica community. The carbon stocks amount of forests in Suji-gu, Yongin City, calculated by applying the biotope map and Biomass Allometric Equations, was relatively higher than the carbon stocks amount calculated by multiplying existing forest standing crop by basic wood density, biomass expansion factor, and carbon fraction. This is because the currently officially used forest standing crop in Yongin City (144.44 m³/ha) does not sufficiently reflect the actual forest vegetation, and trees with a breast height diameter of less than 6 cm were excluded when surveying forest standing crop, resulting in a lower carbon stocks amount than the actual amount. This study complements the limitations of existing carbon stocks calculation methods by utilizing a biotope map with detailed information on vegetation, such as existing vegetation maps and land cover status, and a Biomass Allometric Equations developed by the National Institute of Forest Science, and provides higher precision when assessing carbon stocks of forests. It is meaningful in suggesting a method for calculating carbon stocks.

• Journal of Nutrition and Health
• /
• v.42 no.1
• /
• pp.78-96
• /
• 2009

The purpose of this study was to analyze and evaluate the menu served in government offices foodservice by using Kasavana & Smith's Menu-Engineering. Sales and food costs were collected from the daily sales reports for a year from Jan 2 to Dec 31 in 2007. Calculation for menu analysis and customer's data were done by computer using the MS 2003 Excel spreadsheet program and SPSS 12.0 package program. Menu mix% (MM%) and unit contribution margin were used as variables by Kasavana & Smith. Four possible classifications by Menu-Engineering technique were turned out as 'STAR', 'PLOWHORSE', 'PUZZLE', 'DOG'. The main menus served during a year were 128 dishes and about 141 peoples visited this restaurant daily. The mean age of the men was $44.1\;{\pm}\;6.3$, women were $32.7\;{\pm}\;6.4$ and showed that was statistically higher than that of women (p < .0001). The rates of STAR menus were 'Western style (75.0%)', 'guk/tang-ryu (48.1%)', 'jjigae/ jeongol-ryu (23.1%)', 'bap-ryu (17.2%)' in sequence. There were no STAR menus in gui/jorim/jjim-ryu. PLOWHORSE menus were 'gui-ryu (75.0%)', 'guk/tang-ryu (29.6%)', 'bap-ryu (27.6%)' in sequence. There were no PUZZLE or DOG menus in 'jjigae/jeongol-ryu'. PUZZLE menus were 'jorim/jjim-ryu and Myeonryu (each 33.3%)', 'bap-ryu (31.0%)' in sequence. PUZZLE menus were a lots of 'Chinese food (75.0%)' and 'myeonryu (55.6%)'. This study provides the basic data based on regularly menu analysis method applied the scientific menu analysis techniques in government offices food services, I'd like to suggest that the menu management must be done based on the necessity and result of menu analysis according to the seasonal and middle, long-term plans.