• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.507-510
• /
• 1998

In this paper, a novel test method is proposed to detect hard and soft fault in CMOS operational amplifiers. Proposed test method mark use of the offset character, which is one of the op-amps characteristics. During the test mode, CUT is implemented to unit gain op-amps with feedback loop. When the input is grounded, a good circuit has a small offset voltage, but a faulty circuit has a large offset voltage exceeding predefined range of tolerance. Using the proposed method, no test vector is required to be applied. Therefore the test vector generation problem is eliminated and the test time is reduced. The accuracy and effectiveness of the method is verified through HSPICE simulation.

• Speech Sciences
• /
• v.11 no.3
• /
• pp.143-156
• /
• 2004

In this paper, we implemented a vocabulary-independent speech recognizer using the TMS320VC33 DSP. For this implementation, we had developed very small-sized recognition engine based on diphone sub-word unit, which is especially suited for embedded applications where the system resources are severely limited. The recognition accuracy of the developed recognizer with 1 mixture per state and 4 states per diphone is 94.5% when tested on frequently-used 2000 words set. The design of the hardware was focused on minimal use of parts, which results in reduced material cost. The finally developed hardware only includes a DSP, 512 Kword flash ROM and a voice codec. In porting the recognition engine to the DSP, we introduced several methods of using data and program memory efficiently and developed the versatile software protocol for host interface. Finally, we also made an evaluation board for testing the developed hardware recognition module.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.356-360
• /
• 2006

Recently, for the purpose of improving the isolation performance of impact noise, many resilient materials have been installed in a residential building. As one of the reduction method for improving the performance of light-weight impact noise, this study is focused on the load condition of floating layer over resilient material. We studied the correlation between the mass or load of the floating layer and the reduction of light-weight impact noise by experiments in reverberation chamber for testing the impact noise. The results show that the reduction of impact noise is improved by increasing the mass per unit area of floating layer until about $140kg/m^2$. But the reduction is not obvious by adding extra mass on the floating layer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4253-4258
• /
• 2012

The investigation of the undrained strength and the important several undrained geotechnical properties was, in detail, made for highly plastic soils using the field and laboratory testing results. The plastic index, activity, water content, and effective unit weight did not show the notable relationship with both Su and normalized Su. The OCR, sensitivity, and undrained elastic modulus presented remarkable tendency with normalized Su. It could be concluded that the use of the normalized Su may lead to the reasonable results then the normalized Su needs further research.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1813-1819
• /
• 2016

In this paper, LS-SynRM (Line Start-Synchronous Reluctance Motor) has been attracting attention in replace of induction motor which hardly provides high efficiency. Compared to induction motor, LS-SynRM has better efficiency per unit area. This study demonstrated the electromagnetic design methods of LS-SynRM while maintaining the frame of existing IE3 induction motor for blower. We documented the design procedures for generating high saliency which is the most essential and mechanical stress analysis is also treated. In conclusion, we proved the validity of our design by manufacturing and testing our LS-SynRM models.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.1036-1042
• /
• 2011

APR1400 RVI CVAP using the non-prototype category II is being conducted to verify integrity of the RVI design and to secure the CVAP technology. The measurement programs are to confirm vibration analysis results for reactor internals during pre-operational and initial startup testing and to determine the safety margin. One of the important basis for the measurement programs is test acceptance criteria. Therefore, this paper is on establishment of response instrumentation test acceptance criteria for APR1400 RVI CVAP. The established acceptance criteria show that the stress criteria of APR1400 RVI are more conservative values than those of the valid prototype plant(Palo Verde unit 1) and, the displacement criteria of the inner barrel assembly and the upper guide structure were established to 0.03 in and 0.01 in, respectively.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.648-655
• /
• 1993

The hydraulic coconut dehusking machine consists of three main parts ie. The frame , the power unit including the hydraulic accessories, the lifting and dehusking mechanisms. Two sets of the hydraulic coconut dehusking machine were developed . their hydraulic and electrical control circuits were connected in series to enable them operating contemporaneously. Two operators are required to operate the machine. Each of them put a coconut on the lifting mechanism in order to start the working cycle automatically. As a result, the nut are immediately pushed up and seized by the holding teeth under the supplement of the hydraulic reducing circuit. After that the dehusking mechanism started operating via the sequence circuit. At the end of the cycle, both mechanisms return to their original positions. Some remaining fibrous is taken out manually from the nut subsequently . The continuous dehusking speed was found to be 22.2 seconds per 2 coconuts.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.640-642
• /
• 2008

This paper presents the design, development and performance of a 250kW power conditioning system(PCS) for large scale photovoltaic power plant. The PV inverter consists of a three phase IGBT stack, L-C filter, transformer and HMI unit for monitoring. To verify the performance of the PV inverter a testing facility was designed and constructed to simulate the characteristics of the solar cell and grid.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.59-62
• /
• 2008

This paper presents the procedure and the results of modal identification testing of a seismic monitoring system central processing unit cabinet for a nuclear power plant. This paper also provides a model updating for making effective analytical modeling of cabinet-type electrical equipment by comparing the test results with the analysis results. From the test results and their interpretation, modal properties (modal frequency, mode shape, and modal damping) of the specimen were satisfactorily identified. However, the analysis results may need to study further to find the effective and presentative model for the cabinet-type electrical equipment. This paper just presents the first stage of the research project "Development of dynamic behavior analysis technique of dynamic structure system" which is trying to build the lumped mass beam stick model even their results do not agree well with the test results.

• Journal of Korean Academy of Nursing
• /
• v.36 no.8
• /
• pp.1295-1300
• /
• 2006

Purpose. The purposes of this methodologic paper are to (1) describe theoretical background in conducting research across different cultures; (2) address measurement issues related to instrument administration; and (3) provide strategies to deal with measurement issues. Methods. A thorough review of the literature was conducted. A theoretical background is provided, and examples of administering instrument in studies are described. Results. When applying an instrument to different cultures, both equivalence and bias need to be established. Three levels of equivalence, i.e., construct equivalence, measurement unit equivalence, and full score comparability, need to be explained to maintain the same concept being measured. In this paper, sources of bias in construct, method, and item are discussed. Issues related to instrument administration in a cross-cultural study are described. Conclusion. Researchers need to acknowledge various group differences in concept and/or language that include a specific set of symbols and norms. There is a need to question the philosophical and conceptual appropriateness of an assessment measure that has been conceptualized and operationalized in a different culture. Additionally, testing different response formats such as narrowing response range can be considered to reduce bias.