• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.10 s.241
• /
• pp.1156-1162
• /
• 2005

In this study, a noble method is proposed to prevent the edge overcoating (EOC) that may develop near the edge of the steel strip in the gas wiping process of continuous hot-dip galvanizing. In our past study (Trans. of the KSME (B), Vol. 27, No. 8, pp. $1105\~1113$), it was found that EOC is caused by the alternating vortices which are generated by the collision of two opposed jets in the region outside the steel strip. When the two opposed jets collide at an angle much less than $180^{o}$, non-alternating stable vortices are established symmetrically outside the steel strip, which lead to nearly uniform pressure on the strip surface. In order to deflect both jets downward by a certain angle, a cylinder with small diameter is installed tangentially to the exit of the lower lip of the two-dimensional jet. In order to find an optimum cylinder diameter, the three dimensional flow field is analysed numerically by using the commercial code, STAR-CD. And the coating thickness is calculated by using an integral analysis method to solve the boundary layer momentum equation. In order to compare the present noble method with the conventional baffle plate method to prevent the EOC, the flow field with a baffle plate is also calculated. The calculation results show that the tangentially installed cylinder at the bottom lip of the jet exit is more effective than the baffle plate to prevent EOC.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.3
• /
• pp.255-267
• /
• 2008

Using the commercial CFD code FLOW-$3D^{(R)}$ which has an implicit General Moving Object (GMO) method, the ship-induced wave has been simulated. In the implicit GMO method of the FLOW-$3D^{(R)}$, a rigid body's motion which is either user-prescribed (prescribed motion) or dynamically coupled to fluid flow (coupled motion) can be computed with six degrees of freedom (DOF). The simulated horizontal wave patterns are agree with the wave patterns represented by depth Froude number. The model has been well-simulated to generate the depth-dependent wave transformation in comparison of uniform depth case to complicated depth case. Additionally, it shows that ship-induced waves have been reasonably generated by two ships passing each other and by a ship moving in a curve. Therefore, it is suggested that the FLOW-$3D^{(R)}$ model calibrated with observed data should provide more accurate prediction for the ship-induced wave in a certain fairway or harbor.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.28
• /
• pp.3-36
• /
• 2005

Most legal systems provides the aggrieved buyer with a right to put an end to the contract. Unlike Civil Law systems, the right is rather complicated and uncertain in Common Law systems because they do not sharply distinguish between a refusal which amounts merely to a defence in the nature of the exceptio non adimpleti contractus, and one which is intended to abrogate the aggrieved party's obligations completely and to seek restitution of what he has already performed. That is, they do not draw any sharp distinction between the right of rejection or revocation and the right to put an end to the contract. This explains why the right to put an end to the contract under Civil Law systems are often compared with the right of rejection or revocation under Common Law systems in most academic papers. Having said that, this article describes and analyzes in detail the relevant UCC rules to the buyer's right of rejection and revocation, particularly the rules on the requirements for the right of rejection or revocation. This is for the purpose of providing legal advice to our sellers residing either in U.S.A. or in Korea who plan to enter into U.S.A markets and take academics' interest in the buyer's right which is deemed to be unique compared to the Civil Law systems. In addition, the study attempts to compare the rules as to the right of rejection and revocation under the UCC with those of English law which are stipulated mainly in the Sale of Goods Act (1979) in a statutory form. This may help one better to understand the rules of the UCC which are mostly originated with English law and to find in what way the rules of the UCC depart from those of English law.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.373-377
• /
• 2006

The valve is used on control of flow and hydraulic in a ship. Flow coefficient of valve importance in the design of valve. In this paper, three-dimensional computer simulations by commercial code CFX were conducted to observe the value type and to measure valve flow coefficient when valve with various angles and uniform incoming velocity were used in a piping system. By contrast, a group of experimental data is used to compare with the data obtained by CFX simulation to investigate the validity of numerical method.

• Journal of Navigation and Port Research
• /
• v.31 no.1 s.117
• /
• pp.49-53
• /
• 2007

The valve is used on control of flow in a ship. Flow coefficient of valve is very importance in the design of valve. In this paper, three-dimensional computer simulations by commercial code CFX were conducted to observe the valve type and to measure flow coefficient when valves with various angles and uniform incoming velocity were used in a piping system. By contrast, a group of experimental data is used to compare with the data obtained by CFX simulation to investigate the validity of numerical method.

• Journal of Biosystems Engineering
• /
• v.25 no.4
• /
• pp.279-286
• /
• 2000

Most of the domestic cold storage rooms are inefficient for agricultural products because of temperature gradients inside the storage rooms. Temperature gradients are developed mainly by improper airflow pattern inside the storage room, which is a main cause of the spoilage of the agricultural products. There proper airflow pattern is essential to minimize these temperature gradients and the spoilage. The performance and characteristics of a cold storage room were determined as a function of airflow pattern and temperature distribution in forced circulation cold storage room. A commercial CFD(computational fluid dynamics) code was used to simulate 3-D airflow in the cold storage room. Solving the flow equations for the storage room, a standard k-$\varepsilon$ turbulent model was implemented to calculate steady state turbulent velocity distribution. The CFD prediction results were compared with temperature measurements inside the cold storage room. In case of pallet storage, Temperature gradients inside pallet storage was reduced because the contact area of cold air expanded through an alley of airflow in storage. But is case of bulk storage, the last temperature of storage considerably rose more than the initial temperature of storage. The reason was that bulk storage didn't include any alley of airflow in storage.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.3
• /
• pp.173-179
• /
• 2016

This is a numerical study on the curved channel type of hydrogen reformer using the commercial code of fluid dynamics. We numerically compared the numerical model in a previous study model and the modelling of a tube type curved channel. In the result of numerical analysis on 4 types of curved channel reformers, the methanol conversion efficiency of type 1~4 were 45.0%, 45.3%, 45.6%, 45.6% respectively, and there was hardly any difference by ${\pm}0.6%$. In light of flow characteristics, the rectangle type tube and the type 2 with $45^{\circ}$ turn showed most uniform flow characteristics and concentration distribution of methanol, and the circular type tube and the type 3 with $90^{\circ}$ turn had most un-uniform flow characteristics and concentration distribution of methanol. We concluded that the design for curved channel reformer has to have rectangle type tube with curve of almost $45^{\circ}$ as in the type of curved pipe with $45^{\circ}$ turn.

• International Commerce and Information Review
• /
• v.14 no.1
• /
• pp.345-366
• /
• 2012

The country using factoring actively today is England. The history of factoring could throw back to the Middle Ages, but modern factoring was developed in colonial age of the United States and it was known throughout England in 1960s. At the beginning, it performed mercantile agent who works in local area in order to get rid of uncertainty and inconvenience of a distant trade, but it was getting developed into a today's factoring system which focusing more on financial function. The factoring is called 'account receivable financing' in the United States and it is started out as sales agent and getting developed to 'del credere agent' who guarantee the payment. The activities of factors have been expanded to not only consignment sale and payment guarantees but also advance financing service. However, at the end of the 19th century, the direct sales(direct marketing) was expanded by the development of telecommunication and transportation technology, and then the marketing service by factor was degraded, but the collection of payment and advance finance had been maintained until now and developed into today's factoring system. Especially, the establishment of Uniform Commercial Code in 1931 had formed the basis for activating factoring in the United States through preparing a legal basis of factoring. Due to changes of international trade environment, most of commercial bank in Korea have to deal with export factoring as a trade finance service and it is desirable to specialize as a financing for small and medium company.