• 한국지반공학회논문집
• /
• 제18권4호
• /
• pp.75-83
• /
• 2002

본 연구에서는 준설토, EPS 그리고 고화재를 혼합한 경량혼합토의 역학적 특성을 일축 및 삼축압축시험을 통하여 고찰하였다. 역학적 특성은 다양한 준설토의 초기 함수비, EPS 함유율, 시멘트 함유율 그리고 양생압력에 대한 경량혼합토의 압축강도에 대하여 연구하였다. 삼축압축상태에서 EPS를 함유한 경량혼합토의 압축강도는 유효구속압에 의존 하지 않는 것으로 나타났다. EPS 함유율이 감소할수록($A_E$<2%) 그리고 시멘트 함유율이 증가할수록($A_c$>2%) 삼축압축강도-변형 거동특성은 극한 압축강도를 지나 급격한 압축강도의 감소를 보이는 시멘트 혼합토의 압축강도-변형 거동특성과 유사한 것으로 나타났다. 200kpa 이상의 압축강도를 요구하는 개량지반에 본 경량혼합토를 적용하는 경우에서 적절한 준설토의 초기함수비, EPS 함유율은 각각 약 165%~175%이상 그리고 3%~4%이상으로 제시할 수가 있었다. 삼축 및 일축압축상태에서 극한 압축강도는 시멘트 함유율이 2%이상에서 거의 증가하지 않음으로서 한계 시멘트 함유율은 2%로 제시할 수가 있었다.

• Geomechanics and Engineering
• /
• 제4권4호
• /
• pp.281-294
• /
• 2012

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.45-53
• /
• 2009

In this study, Finite Element Analysis (FEA) was used to decide three kinds of material property of vibration proof rubber with the unique characteristic of non-linear and large deformation. As well, three types of hardness (Hs 50, 55, 60) were compared with the result of fatigue tests, fatigue life was able to be predicted. The request for fatigue life becomes strict more and more as increasing stress under conditions like a compaction, high load and high temperature for parts because it is main characteristics of rubber mount for automotive. Regarding to the fatigue life under dynamic deformation condition, it can be predicted as checking forced deformation extends and its frequency and its strain-life curve. As for material property tests of uniaxial tension test, uniaxial compression test, pure shear test, Ogden model was used for FEA by observing relations between stress and strain's rate as curve fitting. As a result of FEA, fatigue life for rubber mount was predicted and accorded well with the experimental data of fatigue test with hourglass specimens. In addition, its property of the predictable fatigue life method suggested in this study was accorded well with the experimental data by comparing the predicted fatigue life of FEA with the result of fatigue test for rubber component of engine rubber mount.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.1032-1040
• /
• 2001

It is widely accepted that the pressure variation of interstitial fluid is one of the most important factors in bone physiology. In order to understand the role of interstitial fluid on porous bony structure, a consideration for the biomechanical interactions between fluid and solid constituents within bone is required. In this study, a poroelastic theory was applied to investigate the elastic behavior of calf vertebral trabecular bone composed of the porous solid trabeculae and the viscous bone marrow. The poroelastic behavior of trabecular bone in a uniaxial stress condition was simulated using a commercial finite difference analysis software (FLAC, Itasca Consulting Group, USA), and tested for 5 different strain rates, i.e., 0.001, 0.01, 0.1, and 10 per second. The material properties of the calf vertebral trabecular bone were utilized from the previous experimental study. Two asymptotic poroelastic responses, the drained and undrained deformations, were predicted. From the predicted results for the simulated five strain rates, it was found that the pore pressure generation has a linearly increasing behavior when the strain rate is the highest at 10 per second, otherwise it showed a nonlinear behavior. The pore pressure generation with respect to the strain was found to be increased as the strain rate increased. The elastic moduli predicted at each strain were 208.3, 212.2, 337.6, 593.1, and 602.2 MPa, respectively. Based on the results of the present study, it was suggested that the calf vertebral trabecular bone could be modeled as a poroelastic material and its strain rate dependent material behavior could be predicted.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.881-889
• /
• 2010

체적 적분방정식법(Volume Integral Equation Method)이라는 새로운 수치해석 방법을 이용하여, 서로 상호작용을 하는 등방성 함유체를 포함하는 등방성 무한고체가 정적 인장하중을 받을 때 무한고체 내부에 발생하는 응력분포 해석을 매우 효과적으로 수행하였다. 즉, 등방성 기지에 다수의 등방성 함유체가 1) 정사각형 배열 형태 또는 2) 정육각형 배열 형태로 포함되어 있는 경우에, 다양한 함유체의 체적비에 대하여, 중앙에 위치한 등방성 함유체와 등방성 기지의 경계면에서의 인장응력 분포의 변화를 구체적으로 조사하였다. 또한, 체적 적분방정식법을 이용한 해를 해석해 또는 유한요소법을 이용한 해와 비교해 봄으로서, 체적 적분방정식법을 이용하여 구한 해의 정확도를 검증하였다.

• 터널과지하공간
• /
• 제19권2호
• /
• pp.158-166
• /
• 2009

Hoek-Brown 암석에서 응력에 의해 발생되는 균열의 전파특성을 수치해석적으로 분석하기 위한 기초연구로서 탄성균열의 균질화 기법이 제안되었다. 균열의 개시조건으로 Hoek-Brown 경험식이 이용되었고, 균열의 방향 탐색을 위해 임계면법이 이용되었다. 균열물질과 무결암으로 구성된 대표체적에 대해 체적평균 응력 및 변형률 개념을 적용하여 균열과 신선암의 역학적 특성을 균질화시킴으로써 등가 이방성매질의 구성관계식을 유도하였다. 제안된 균질화모델을 포트란 코드로 작성하여 상업유한요소 코드인 COSMOSM에 이식하였다. 제안된 수치해석모델의 적합성을 검증하기 위하여 2차원 평면변형률조건에서 수치 일축압축시험을 실시하였다. 모델 상하부 가압면의 구속조건을 달리한 2가지 해석모델을 선정하여 구속조건이 일축압축시험편의 변형 및 파단면 형성형태에 미치는 영향이 분석되었다. 균열의 균질화를 고려한 수치 일축압축시험 결과는 실제 실험에서 발생되는 형태와 유사한 변형거동 및 파단면 형성 특성을 잘 나타내었다.

• 터널과지하공간
• /
• 제11권3호
• /
• pp.217-224
• /
• 2001

암석은 지질학적 생성과정으로 인해 많은 역학적 결함을 포함하고 있으며 이러한 결함 사이에는 암석 브릿지가 존재하게 된다. 이러한 암석 브릿지에서의 균열의 전파 및 결합(coalescence)과정은 사면, 기초, 터널 등의 안정성에 영향을 미치게 된다. 본 연구에서는 단축압축 하에서 균열의 형상변화에 따른 암석 브릿지에서의 균열의 개시, 전파 및 결합거동 변화에 대해 알아보았다. 여산 대리석을 재료로 120$\times$60$\times$25 mm크기의 시료에 균열각도 $\alpha$, 브릿지각도 $\beta$, 균열길이 2c, 브릿지길이 2b를 변화시키면서 2개의 인공균열을 제작하였다. 하중을 가하면서 날개형 균열개시응력, 날개형 균열 전파각도, 균열결합 응력을 측정하였으며 균열결합 유형을 정리하였다. 또한, 정규화된 최대강도(normalized peak strength)를 구하여 Ashby & Hallam 모형 (1986)의 이론해와 비교, 분석 하였다.

• 대한기계학회논문집A
• /
• 제36권1호
• /
• pp.59-71
• /
• 2012

체적 적분방정식법(Volume Integral Equation Method)이라는 새로운 수치해석 방법을 이용하여, 서로 상호작용을 하는 등방성 또는 이방성 다이아몬드 형 함유체를 포함하는 등방성 무한고체가 정적 인장하중을 받을 때 무한고체 내부에 발생하는 응력분포 해석을 매우 효과적으로 수행하였다. 즉, 등방성 기지에 다수의 등방성 또는 이방성 다이아몬드 형 함유체의 중심이 1) 정사각형 배열 형태 또는 2) 정육각형 배열 형태로 포함되어 있는 경우에, 다양한 다이아몬드 형을 포함하는 원형 실린더 함유체의 체적비에 대하여, 중앙에 위치한 다이아몬드 형 함유체와 등방성 기지의 경계면에서의 인장응력 분포의 변화를 구체적으로 조사하였다. 또한, 체적 적분방정식법을 이용하여 구한 해의 정확도를 검증하기 위하여, 체적 적분방정식법을 이용한 해를 유한요소법을 이용한 해와 비교해 보았다.

• Geomechanics and Engineering
• /
• 제19권1호
• /
• pp.49-60
• /
• 2019

Crack instability propagation during coal and rock mass failure is the main reason for electromagnetic radiation (EMR) generation. However, original cracks on coal and rock mass are hard to study, making it complex to reveal EMR laws and mechanisms. In this paper, we prefabricated cracks of different inclinations in coal and rock samples as the analogues of the native cracks, carried out uniaxial compression experiments using these coal and rock samples, explored, the effects of the prefabricated cracks on EMR laws, and verified these laws by measuring the surface potential signals. The results show that prefabricated cracks are the main factor leading to the failure of coal and rock samples. When the inclination between the prefabricated crack and axial stress is smaller, the wing cracks occur first from the two tips of the prefabricated crack and expand to shear cracks or coplanar secondary cracks whose advance directions are coplanar or nearly coplanar with the prefabricated crack's direction. The sample failure is mainly due to the composited tensile and shear destructions of the wing cracks. When the inclination becomes bigger, the wing cracks appear at the early stage, extend to the direction of the maximum principal stress, and eventually run through both ends of the sample, resulting in the sample's tensile failure. The effect of prefabricated cracks of different inclinations on electromagnetic (EM) signals is different. For samples with prefabricated cracks of smaller inclination, EMR is mainly generated due to the variable motion of free charges generated due to crushing, friction, and slippage between the crack walls. For samples with larger inclination, EMR is generated due to friction and slippage in between the crack walls as well as the charge separation caused by tensile extension at the cracks' tips before sample failure. These conclusions are further verified by the surface potential distribution during the loading process.

• Geomechanics and Engineering
• /
• 제30권3호
• /
• pp.259-272
• /
• 2022

Rockburst is a dynamic, multivariate, and non-linear phenomenon that occurs in underground mining and civil engineering structures. Predicting rockburst is challenging since conventional models are not standardized. Hence, machine learning techniques would improve the prediction accuracies. This study describes decision based uncertainty models to predict rockburst in underground engineering structures using gradient boosting algorithms (GBM). The model input variables were uniaxial compressive strength (UCS), uniaxial tensile strength (UTS), maximum tangential stress (MTS), excavation depth (D), stress ratio (SR), and brittleness coefficient (BC). Several models were trained using different combinations of the input variables and a 3-fold cross-validation resampling procedure. The hyperparameters comprising learning rate, number of boosting iterations, tree depth, and number of minimum observations were tuned to attain the optimum models. The performance of the models was tested using classification accuracy, Cohen's kappa coefficient (k), sensitivity and specificity. The best-performing model showed a classification accuracy, k, sensitivity and specificity values of 98%, 93%, 1.00 and 0.957 respectively by optimizing model ROC metrics. The most and least influential input variables were MTS and BC, respectively. The partial dependence plots revealed the relationship between the changes in the input variables and model predictions. The findings reveal that GBM can be used to anticipate rockburst and guide decisions about support requirements before mining development.