• 보존과학연구
• /
• 통권29호
• /
• pp.149-162
• /
• 2008

Because stone cultural heritages in Korea are mostly situated outdoors without any notable protection, there are severe damages from physical, chemical and biological weathering. And this in turn causes deformation and structural damage. To counteract this problem and increase durability, various kinds of conservation materials are used in the conservation and restoration treatment. However, there are not many practical and technological experiments on this subject. Accordingly this research is for analysis of effect for treatment to make use a resin of the ethyl silicate for the granite in Mt. Nam of Gyeongju. It takes a long time to confirm the test result regarding durability and side effects of the conservatives after treatment. So we built up an artificial environment through freezing and melting test, and evaluated the conservation materials. As a result of this experiment, porosity and absorptivity was increased in accordance with processing of freezing and melting test. But other things such as elastic wave speed, elastic modulus, uniaxial compressive strength and tensile strength was decreased. It will make a plan to form a method of research systematically for mechanism and element of weathering and to elicit a correlation among experiment of artificial weathering and practical natural weathering from next research.

• 산업기술연구
• /
• 제19권
• /
• pp.67-74
• /
• 1999

The mechanical properties including forming limit and deep-drawability of commercially-used sheet metals were experimentally estimated in this study. Uniaxial tensile test to obtain basic mechanical properties was carried out, followed by limiting dome height (LDH) test and forming limit diagram (FLD) test to quantitatively evaluate the sheet-formability. Deep drawing and reverse drawing tests were also performed to find out the critical values of the blank holding force and the gap between the die and the blank holder which enabled the deep drawing and reverse drawing of a successful cop without any wrinkle or fracture. The thickness of the cup wall along the rolling-, transeverse- and $45^{\circ}$-directions was measured and compared with one another. And the punch force-stroke curve and the critical punch force expected from the theory coincided with the experimental result very well for mild steel while not for aluminium alloy.

• 한국건설순환자원학회논문집
• /
• 제8권3호
• /
• pp.349-355
• /
• 2020

이 연구의 목적은 섬유의 혼입량과 종류에 따른 고강도 섬유보강 복합재료의 정적하중에서의 압축강도 및 인장거동과 비상체 하중 하에서의 충격 저항성을 조사하고자 한다. 이를 위하여 3가지 배합을 설계하였고, 압축강도, 직접인장, 그리고 고속 비상체 충돌 실험을 수행하였다. 실험결과 섬유의 혼입량은 압축강도에 비하여 인장강도에 큰 영향을 미치며, 하이브리드 섬유 사용으로 인장변형성능이 향상되는 것으로 나타났다. 강섬유의 혼입량은 충격 저항성에 큰 영향을 미치는 것으로 나타났다. 하이브리드 섬유를 사용하면 충격 저항성이 더욱 향상되는 것으로 나타났다. 다만, 단일 섬유 사용에 비하여 실험체별성능 차이가 크게 발생하는 것으로 나타났다.

• Advances in concrete construction
• /
• 제7권2호
• /
• pp.117-126
• /
• 2019

When designing reinforced concrete (RC) members, the rebar is assumed to resist all tensile forces, but the resistance of the concrete in the tension area is neglected. However, concrete can also resist tensile forces and increase the tensile stiffness of RC members, which is called the tension stiffening effect (TSE). Therefore, this study assessed the TSE, particularly after yielding of the steel bars and the effects of the steel ratio on the TSE. For this purpose, RC member specimens with steel ratios of 2.87%, 0.99%, and 0.59% were fabricated for uniaxial tensile tests. A vision-based non-contact measurement system was used to measure the behavior of the specimens. The cracks on the specimen at the stabilized cracking stage and the fracture stage were measured with the image analysis method. The results show that the number of cracks increases as the steel ratio increases. The reductions of the limit state and fracture strains were dependent on the ratio of the rebar. As the steel ratio decreased, the strain after yielding of the RC members significantly decreased. Therefore, the overall ductility of the RC member is reduced with decreasing steel ratio. The yielding plateau and ultimate load of the RC members obtained from the proposed equations showed very good agreement with those of the experiments. Finally, the image analysis method was possible to allow flexibility in expand the measurement points and targets to determine the strains and crack widths of the specimens.

• 비파괴검사학회지
• /
• 제30권5호
• /
• pp.471-478
• /
• 2010

박막은 마이크로 전자 장치, 자기 기록 매체, 미세 기전 시스템 및 표면 코팅과 같은 다양한 응용에 있어서 매우 중요한 역할을 수행하는 재료이다. 이러한 박막의 재료 물성 값은 상응하는 거시 재료의 물성 값과 다를 수 있기 때문에 박막의 기계적 물성 값들을 신뢰성 있게 측정할 수 있는 시험법의 개발이 요구되어져 왔다. 본 연구에서는 종래의 약 처짐 시험법과 단축 인장 시험법의 한계성을 극복하기 위해 나노미터 이하의 면외 변위 측정 분해능을 갖는 백색광 간섭계를 채택한 새롭고 간편한 시험법을 개발하였다. 개발된 시험법의 유효성을 검증해 보기 위하여 스퍼터링을 포함한 마이크로 공정에 의해 자유지지 알루미늄 박막 시험편을 제작한 뒤 이를 이용하여 인장 물성 값을 측정하였다. 폭 0.5 mm, 두께 $1{\mu}m$인 시험편을 실리콘 다이상에 1~5개 제작하여 사용하였다. 모터 구동 팁, 하중계 및 6 자유도 정렬 장치로 구성된 시험기를 자체적으로 제작한 뒤 막 처짐 시험을 수행하였다. 시험기는 가능한 작게 제작하여 상용 백색광 간섭 현미경 아래에 설치 가능하도록 하였다. 백색광 간섭무늬를 이용하여 시험편과 시험기 사이의 정렬 맞춤을 수행하였다. 영 계수는 62 GPa, 항복점은 247 MPa로 측정되었다.

• Geomechanics and Engineering
• /
• 제17권4호
• /
• pp.333-342
• /
• 2019

Geological dynamic hazards during coal mining can be caused by the failure of a composite system consisting of roof rock and coal layers, subject to different loading rates due to different advancing velocities in the working face. In this paper, the uniaxial compression test simulations on the composite rock-coal layers were performed using $PFC^{2D}$ software and especially the effects of loading rate on the stress-strain behavior, strength characteristics and crack nucleation, propagation and coalescence in a composite layer were analyzed. In addition, considering the composite layer, the mechanisms for the advanced bore decompression in coal to prevent the geological dynamic hazards at a rapid advancing velocity of working face were explored. The uniaxial compressive strength and peak strain are found to increase with the increase of loading rate. After post-peak point, the stress-strain curve shows a steep stepped drop at a low loading rate, while the stress-strain curve exhibits a slowly progressive decrease at a high loading rate. The cracking mainly occurs within coal, and no apparent cracking is observed for rock. While at a high loading rate, the rock near the bedding plane is damaged by rapid crack propagation in coal. The cracking pattern is not a single shear zone, but exhibits as two simultaneously propagating shear zones in a "X" shape. Following this, the coal breaks into many pieces and the fragment size and number increase with loading rate. Whereas a low loading rate promotes the development of tensile crack, the failure pattern shows a V-shaped hybrid shear and tensile failure. The shear failure becomes dominant with an increasing loading rate. Meanwhile, with the increase of loading rate, the width of the main shear failure zone increases. Moreover, the advanced bore decompression changes the physical property and energy accumulation conditions of the composite layer, which increases the strain energy dissipation, and the occurrence possibility of geological dynamic hazards is reduced at a rapid advancing velocity of working face.

• 한국공간구조학회논문집
• /
• 제1권2호
• /
• pp.93-100
• /
• 2001

A stress-strain relationship for reinforced concrete membrane elements subjected to reversed cyclic loading is quite different to that of concrete cylinder subjected to uniaxial compression. The compressive strength of cracked concrete membrane elements is reduced by cracking due to tension in the perpendicular direction. Based on the three reinforced concrete panel tests, a softened stress-strain curve of concrete subjected to reversed cyclic loading is proposed. The proposed model consists of seven stages in the compressive zones and six stages in the tensile zones. The proposed model is verified by comparing to the test results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.58-61
• /
• 1998

Anisotropy is closely related to the formability of sheet metal and should be considered carefully for more realistic analysis of actual sheet metal forming operations. In order to better describe anisotropic plastic properties of aluminum alloy sheets, a planar anisotropic yield function which accounts for the anisotropy of uniaxial yield stresses and strain rate ratios simultaneously was proposed recently[1]. This yield function was used in the finite element simulations of cup drawing tests for an aluminum alloy 2008-T4. Isotropic hardening with a fixed initial back stress based on experimental tensile and compressive test results was assumed in the simulation. The computation results were in very good agreement with the experimental results. It was shown that the initial back stress as well as the yield surface shape have a large influence on the prediction of the cup height profile.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.89-93
• /
• 1997

A superlastic material, aluminum - lithium alloy 8090, were examined with uniaxial tensile test to investigate its thermomechanical behavior. The tests were carried out at the strain-rates ranging from 2${\times}$10-4 to 1${\times}$10-2 and at the temperatures from 48 0$^{\circ}C$ to 540$^{\circ}C$. The experiments produced force-displacement curves which converted to stress-strain curves. From the curves, several important superplastic factor such as strain-rate sensitivity, optimum strain-rate and strength coefficient were obtained.

• 한국항공운항학회지
• /
• 제20권1호
• /
• pp.103-111
• /
• 2012

This study reviews several fracture models for predicting the residual strength of notched composite laminates. Representative experimental results on the residual strength of composite laminates containing a notch subjected to static uniaxial tensile loading have been collected from open literature. And notched strength data for T300/5208 are analyzed. The various parameters associated with the fracture models have been determined for laminates. Notched strength data sets are compared with fracture models and the applicability of the different fracture models in predicting the notched strength of composite laminates is discussed. And static tests have been performed on 2.0mm depth notched specimen. And the test results are compared with analysis models.