• Journal of the Korean Geotechnical Society
• /
• v.34 no.10
• /
• pp.39-49
• /
• 2018

In this study, aimed at determining the elastic modulus of deep mixed samples, 320 test specimens were developed by mixing 8%, 10%, 12%, and 14% of stabilizer mixture in the granular conditions of clay, sand and gravel. Uniaxial compression tests were carried out using these specimens, and the uniaxial compression strength and strain were analyzed to determine the secant elastic modulus and tangent elastic modulus. Laboratory test results showed that the uniaxial compression strength of all deep mixed samples increased with increasing curing time and stabilizer mixing ratio, and that the secant elastic modulus and the tangen elastic modulus also increased. The increase of the elastic modulus according to the curing period turned out greater in the tangent elastic modulus than in the secant elastic modulus. In order to measure elastic modulus with changes in stabilizer mixing ratio, the correlation coefficient between the elastic modulus for stabilizer mixing ratio of 8% and that of 10%, 12% and 14% was calculated respectively by the specimen condition. The elastic modulus tended to increase as the grain size in a deep mixed specimen increased. The distribution of grain size that had the greatest effect appeared when the composition ratio of sand was high. On the other hand, the increase in the elastic modulus was larger in the sand specimens than in the clay and gravel specimens. Based on these results, it is suggested that a pertinent soil parameter of the deep mixed ground in the field may be obtained by the particle size distribution and the mixing ratio of stabilizer of the deep mixed soil.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.327-333
• /
• 2004

Corestone ground mass has complicated characteristics as it is made up of hard and stiff corestone in a relatively weak and soft matrix. Model corestone ground mass which is physically identical with the stiff corestone in weak matrix were tested in uniaxial compression. The tests show that the increase of the corestone proportion brought the gradual increase of the elastic modulus as well. The ground mass was weaker when the corestone proportion was low while it was stronger in higher corestone proportion. The size of the corestone had no influence on the strength and elastic modulus as long as the proportion of the corestone remains same.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.605-612
• /
• 2002

The objective of this study is to investigate the behavior of Visco-Elasto-Plastic materials of Silicate Grouted Sands due to external load. Uniaxial compression strength of silicate grouted sands was increased accordingly with curing time, but it was almost unchanged after 7days. A series of uniaxial compression creep tests were peformed for $\sigma$/$\sigma$$\sub$f/ = 8%,16% and 24%. The tested Silicated Grouted Sands exhibits three types of strains : elastic, plastic, viscoelastic. It is seen that the magnitude of the instantaneous recoverable strains $\varepsilon$$\sub$r/(o) is approximately independent of the unloading time. In this tests, The total creep strains( elastic, plastic, viscoelastic) are proportional to the stress level. Based on the constant creep test results, relationships between the time and the creep compliance are developed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1487-1493
• /
• 2008

The frost heaving is related with thermal conduction rate and permeability. If the thermal conduction rate can be controlled, it is effective to prevent from frost heaving. If soil mixed with shredded tire which has relatively lower thermal conduction rate than soil, it helps preventing from frost heaving. However, in this case, the shear strength can get weak. In this study, we compared thermal conduction rate of soil and shredded tire, and test uniaxial compression strength of soil which is mixed with shredded tire and cement in different ratio.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.655-662
• /
• 2003

Slope stability is an important issue ill civil engineering works or in open pit mines where both economy and efficiency is required. These are the long-term stability problems which depend on the change of physical properties under a certain weather condition. These can also result in progress of weathering which can change mechanical or hydro-geological properties of rock mass considerably. In this study, weathering in nature was simulated by freeze-thaw test and Soxhlet test which represent mechanical and chemical weathering respectively. Measured were elastic wave velocities, absorption rate, volume change. Uniaxial compression strengths before and after the weathering tests were also measured. The change in weight and volume of the specimens were not clearly related to the weathering process, but P, S wave velocities were clearly decreased as weathering progresses. For some class of rocks, P-wave velocity was increased probably because of the saturation due to improved connectivity of the pre-existing pores. Based on the test results, stability of the slopes were analyzed using FLAC$\^$2D/. Due to the reduced strength parameters, the factors of safety were decreased for the selected sites.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.1 s.68
• /
• pp.7-15
• /
• 2006

In this research, the behavior characteristics of cement mixing lightweight soil (CMLS) for recycling of dredged soil in the Nakdong River estuary are experimentally investigated. CMLS is composed of the dredged soil from Nakdong River estuary, cement, and air foam. For this purpose, uniaxial compression tests are carried out for artificially prepared specimens of CMLS, with various initial water contents, cement contents, and mixing ratio of dredged soils. The experimental results of CMLS indicated that the compressive strength is strongly influenced by the cement contents, rather than water contents and air foam. Compressive strength of CMLS increased with an increase in cement content, while it decreased with an increase in water content and air foam content. It was also found that the modulus of deformation E50 was in a range of 44 to 128 times greater than the value of uniaxial compressive strength, cured in 28 days.

• Tunnel and Underground Space
• /
• v.11 no.4
• /
• pp.301-310
• /
• 2001

Gypsum blocks with sixteen flaws have been prepared and tested in uniaxial compression. Results from these experiments are compared with observations from the same material with two and three flaws. The results indicate that the cracking pattern observed in specimens wish multiple flaws is analogous to the pattern obtained in specimens with two and three flaws such as initiation and propagation of wing, and secondary cracks and coalescence. Wing cracks initiate at an angle with the flaw and propagate in a stable manner towards the direction of maximum compression. Secondary cracks initiate and propagate in a stable manner. As the load is increased, secondary cracks may propagate in an unstable manner and produce coalescence. Two types of secondary cracks are observed: quasi-coplanar, and oblique secondary cracks. Coalescence is produced by the linkage of two flaws: wing and/or secondary cracks. From the sixteen flaws test, four types of coalescence are observed. Observed types of coalescence and initiation stress of wing and secondary crackle depend on flaw geometries, such as spacing, continuity, flaw inclination angle, ligament angle, and steppings.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.501-506
• /
• 1999

The purpose of this study is to experimentally investigate the strength and ductility of reinforced high strength concrete columns under uniaxial load and several test variables. To do this, we have conducted tests on thirteen 20$\times$20$\times$60cm specimens with 8 and 12 longitudinal steel bars subjected to monotonic uniaxial compression. The main variables considered in this test are the configuration of ties, the space the ties, the diameter of ties and yield strength of ties. The results indicate that the strength and the ductility of reinforced high strength concrete columns have been influenced on these variables except yield strength of ties. Judging from test results, real stress of ties at peak concrete stress is suitable variable than yield strength of ties for estimation of the strength gain factor(Ks).

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.4
• /
• pp.31-35
• /
• 2018

When REBCO coated conductors (CCs) are applied to superconducting devices such as coils and magnets, they are subjected to deformation in various modes such as compression/tension bending, uniaxial/transverse tension and torsion. Despite outstanding performances by REBCO CC tapes, their electromechanical properties have been evaluated primarily under uniaxial tension, therefore data about the critical current ($I_c$) response in the compressive strain region are lacking. In this study, the characteristic responses of $I_c$ in REBCO CC tapes under bending strains in the range from tensile to compressive were evaluated. The springboard bending beam was used, wherein the CC tape sample was soldered onto the surface of the springboard. A Goldacker-type bending test rig, which lacks a support holding the sample during testing, was used as a comparator. Degradation in $I_c$ behaviors, including strain sensitivity, in differently processed REBCO CC tapes were examined based on the test rig used.

• Smart Structures and Systems
• /
• v.22 no.6
• /
• pp.643-662
• /
• 2018

One of the methods for investigation of mechanical behavior of materials is numerical simulation. For simulation, its need to model behavior is close to real condition. PFC is one of the rock mechanics software that needs calibration for models simulation. The calibration was performed based on simulation of unconfined compression test and Brazilian test. Indeed the micro parameter of models change so that the UCS and Brazilian test results in numerical simulation be close to experimental one. In this paper, the effect of four micro parameters has been investigated on the uniaxial compression test and Brazilian test. These micro parameters are friction angle, Accumulation factor, expansion coefficient and disc distance. The results show that these micro parameters affect the failure pattern in UCS and Brazilian test. Also compressive strength and tensile strength are controlled by failure pattern.