• Korean Journal of Geomatics
• /
• v.3 no.1
• /
• pp.33-41
• /
• 2003

Every year, several typhoons hit the Korean peninsula and cause severe damage. For the prevention and accurate estimation of these damages, real time or almost real time flood information is essential. Because of weather conditions, images taken by optic sensors or LIDAR are sometimes not appropriate for an accurate estimation of water areas during typhoon. In this case SAR (Synthetic Aperture Radar) images which are independent of weather condition can be useful for the estimation of flood areas. To get detailed information about floods from satellite imagery, accurate classification of water areas is the most important step. A commonly- and widely-used classification methods is the ML(Maximum Likelihood) method which assumes that the distribution of brightness values of the images follows a Gaussian distribution. The distribution of brightness values of the SAR image, however, usually does not follow a Gaussian distribution. For this reason, in this study the ANN (Artificial Neural Networks) method independent of the statistical characteristics of images is applied to the SAR imagery. RADARS A TSAR images are primarily used for extraction of water areas, and DEM (Digital Elevation Model) is used as supplementary data to evaluate the ground undulation effect. Water areas are also extracted from KOMPSAT image achieved by optic sensors for comparison purpose. Both ANN and ML methods are applied to flat and mountainous areas to extract water areas. The estimated areas from satellite imagery are compared with those of manually extracted results. As a result, the ANN classifier performs better than the ML method when only the SAR image was used as input data, except for mountainous areas. When DEM was used as supplementary data for classification of SAR images, there was a 5.64% accuracy improvement for mountainous area, and a similar result of 0.24% accuracy improvement for flat areas using artificial neural networks.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.299-303
• /
• 2008

In this study, an uncertainty assessment for surface air temperature(T2m) and precipitation(PCP) over East Asia is carried out. The data simulated by the intergovermental Panel on Climate Change (IPCC) Fourth Assessment Report (AR4) Atmosphere-Ocean coupled general circulation Model (AOGCM) are used to assess the uncertainty. Examination of the seasonal uncertainty of T2m and PCP variabilities shows that spring-summer cold bias and fall warm bias of T2m are found over both East Asia and the Korea peninsula. In contrast, distinctly summer dry bias and winter-spring wet bias of PCP over the Korea peninsula is found. To investigate the PCP seasonal variability over East Asia, the cyclostationary empirical orthogonal function(CSEOF) analysis is employed. The CSEOF analysis can extract physical modes (spatio-temporal patterns) and their undulation (PC time series) of PCP, showing the evolution of PCP. A comparison between spatio-temporal patterns of observed and modeled PCP anomalies shows that positive PCP anomalies located in northeastern China (north of Korea) of the multi-model ensemble(MME) cannot explain properly the contribution to summer monsoon rainfalls across Korea and Japan. The uncertainty of modeled PCP indicates that there is disagreement between observed and MME anomalies. The spatio-temporal deviation of the PCP is significantly associated with lower- and upper-level circulations. In particular, lower-level moisture transports from the warm pool of the western Pacific and corresponding moisture convergence significantly contribute to summer rainfalls. These lower- and upper-level circulations physically consistent with PCP give a insight of the reason why differences between modeled and observed PCP occur.

• Spatial Information Research
• /
• v.17 no.1
• /
• pp.89-102
• /
• 2009

The information of ocean topology is the fundamental source which is necessary for understanding the ocean, producing nautical charts and delimiting maritime boundaries. An echo sounder is being used generally to collect undersea bathymetric data, but an indirect method such as geophysical data acquired by satellites is being used recently. In this study, the outputs of ocean surveying for the production of the Basic Maps of the Sea in 1996 and 1997 in the East Sea and the bathymetric data produced by geophysical data are compared and analyzed. The study areas are Ulleung Plateau, Ulleung Basin and the southern area of Ulleung Basin which have different geophysical characteristics. Through this study, we found that the bathymetric data acquired by an indirect method using satellite is similar to the field surveying results in general configuration of ocean floor and average depth. However, the minimum square error is about 100m in 1700m depth, and it has been observed a local error up to 1000m. In addition, it has been found that the detailed undulation of ocean topology is shown on the gravity data which is acquired by the research vessel.

• Applied Microscopy
• /
• v.35 no.4
• /
• pp.74-83
• /
• 2005

The ontogeny of pollen wall in Panax ginseng was studied with transmission and scanning electron microscopy from early tetrad stage until pollen maturity. Initial indication of exine development is undulation of plasma membrane for the preparation of bacular mound. The first recognizable structure of the pollen wall is the cellulosic primexine which is formed outside of the plasma membrane while microspore tetrads are still surrounded by callose wall. As development proceeds, foot-layer and baculum differentiation, callose dissolution and exine formation were progressed. During this process, sporopollenin is deposited into the exine, and then endexine development was followed. The intine, innermost pollen wall layer, is developing form hypertrophic Golgi vesicles. The thickness of exine is very even on all along the pollen wall, but intine thickness of apertural region is thicker than that of nonapertural region. Mature pollen of ginseng is $20{\mu}m$ in size, tricolpate and shows fine reticulate sculpturing.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.8
• /
• pp.79-85
• /
• 2004

In this paper, the RF-ID system for ubiquitous tagging applications has been designed, fabricated and analysed. The RF-ID System consists of passive RF-ID Tag and Reader. The passive RF-ID tag consists of rectifier using zero-bias schottky diode which converts RF power into DC power, ID chip, ASK modulator using bipolar transistor and slot loop antenna. We suggest an ASK undulation method using a bipolar transistor to compensate the disadvantage of the conventional PIN diode, which needs large current Also, the slot loop antenna with wider bandwidth than that of the conventional patch antenna is suggested The RF-ID reader consist of patch array antenna, Tx/Rx part and ASK demodulator. We have designed the RF-ID System using EM and circuit simulation tools. According to the measured results, The power level of modulation signal at 1 m from passive RF-ID Tag is -46.76 dBm and frequency of it is 57.2 KHz. The transmitting power of RF-ID reader was 500 mW

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.35-43
• /
• 2005

Matrix converters have been studied for eliminating dc link of conventional converter-inverter system, and various undulation strategy have been proposed. Therefore, matrix converter have no energy storage component except for small ac later for the elimination of switching ripple, and can be made compact and highly reliable compare with the do link inverter system. Matrix converter, however, directly connected the input and the output terminals by bidirectional static switch. As a result if the input voltage are asymmetrical, and contain harmonics, the influence of the distortions directly appear on the output terminal. This problem is a major obstacle to the matrix converter. A new control method using average comparison strategy have been proposed in this paper. This control method realizes sinusoidal input and output current unity input displacement factor regardless of load power factor. Moreover, compensation of the asymmetrical and/or harmonic containing input voltage is automatically realized, and calculation time of control function is reduced.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.335-335
• /
• 2011

Instability of a thin film attached to a compliant substrate often leads to emergence of exquisite wrinkle patterns with length scales that depend on the system geometry and applied stresses. However, the patterns that are created using the current techniques in polymer surface engineering, generally have low aspect ratio of undulation amplitude to wavelength, thus, limiting their application. Here, we present a novel and effective method that enables us to create wrinkles with a desired wavelength and high aspect ratio of amplitude over wavelength as large as to 2.5:1. First, we create buckle patterns with high aspect ratio of amplitude to wavelength by deposition of an amorphous carbon film on a surface of a soft polymer poly(dimethylsiloxane) (PDMS). Amorphous carbon films are used as a protective layer in structural systems and biomedical components, due to their low friction coefficient, strong wear resistance against, and high elastic modulus and hardness. The deposited carbon layer is generally under high residual compressive stresses (~1 GPa), making it susceptible to buckle delamination on a hard substrate (e.g. silicon or glass) and to wrinkle on a flexible or soft substrate. Then, we employ glancing angle deposition (GLAD) for deposition of a high aspect ratio patterns with amorphous carbon coating on a PDMS surface. Using this method, pattern amplitudes of several nm to submicron size can be achieved by varying the carbon deposition time, allowing us to harness patterned polymers substrates for variety of application. Specifically, we demonstrate a potential application of the high aspect wrinkles for changing the surface structures with low surface energy materials of amorphous carbon coatings, increasing the water wettability.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.4
• /
• pp.383-388
• /
• 2002

This study suggests a data processing method for precise geoid height calculation through sea gravity data of mid-Yellow Sea provided by Haeyang 2000 and satellite altimetry data and the EGM96 geopotential model from GSFC/DMA in USA. Also it compared sea gravity data with satellite altimetry gravity data. As a result, precise geoidal undulation of the mid-Yellow Sea presented from calculating and integrating EGM96 geopotential model in degree and order 167 and a relative geoid by integral radius of 27km respectively It has a mean value of 18.339m, varying from 13.564m to 22.785m. the comparison between sea gravity data and satellite altimetry data shows that the former is more precise than the latter, which showed an anomaly of 0.56m0Gal and RMSE of 4.195m.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2008.10a
• /
• pp.93-96
• /
• 2008

We analyze a precise seabed feature around the Hupo Bank by using Multi-beam echosounder. Multi-beam echosounder system can observe the topography undulation according to the navigation of the survey ship by shooting wide beam. It is possible to embody a precision seabed feature because it can be make high density of incompletion depth sounding between survey lines. Through this survey, there is the Hupo Bank which is 84 km long, 1-15 km wide, 5.3-160 m deep in the center, at the west is moat, at the east is scarp and submarine canyon. The top of the Hupo Bank is the Wangdol reef that has 5.3 m in depth of water at least. Moat in survey area is 30 m long, and 30-40 m wide and has a depressed channel. The gap of depth of water in scarp is approximately 60 m and shows a characteristic of cuttig plane. Submarine canyon is 3.5 - 13.5 km wide.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1311-1319
• /
• 1990

For the purpose of preventing the flow undulation in the cascade of steam turbine, the blades are made into a constant expansion rate in static pressure. And the flow in those cascades is transonic or supersonic in the range of 0.7-2.0 in Mach number. As a consequence, an oblique shock wave, known as inner or outer edge shock wave, arises in the flow of cascades. Especially when the steam in cascades is in a state of high wetness, nonequilibrium condensation and condensation shock wave occur, and they give rise to an interference with oblique shock wave. In the present study the case of expansion of moist air through a supersonic nozzle of constant expansion rate, which behaves similar to that of wet steam, was adopted. The effect of nonequilibrium condensation on the oblique shock wave generated by placing the wedge into the supersonic part of the nozzle was investigated. Furthermore, the relationship between nonequilibrium condensation zone and incident point of the oblique shock wave, oblique shock wave angle, the variations of angles of incident and reflected shock waves due to the variation of initial stagnation supersaturation and the relationship between the height of Mach stem and initial stagnation supersaturation are discussed.