• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.4
• /
• pp.283-291
• /
• 1994

This paper describes about the behavior of the Striped mullet (Mugil cephalus) in the setnet by telemetry techniques. The telemetry system consists of a pinger of 50KHz, three omni-directional hydrophones and ultrasonic receivers, a single board computer for the signal processing, two RF transceivers for the data comunication and a personnel computer. The fish tagged the pinger was tracked by the LBL method, and its location was calculated by the hyperbolic method. The fish escaped from sea surface to 7m deep right after release and had been swum near the sea surface after 30 minutes being released. Also, in horizontal movements, the fish stayed long time around the enterance of the square net in setnet, and showed the escaping behavior repeatly. The average speed of the fish was about 0.41m/sec(1.1 times of the body length)

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.4
• /
• pp.273-282
• /
• 1994

This paper describes about the behavior of the lseraeli carp (Cyprinus cartio. body length 43cm) and the Red seabream (Chrysophrys major. body length 35cm) aquacultured by telemetry techniques. The telemetry system consists of a pinger of 50kHz, three omni-directional hydrophones and ultrasonic receivers, a single board computer for the signal processing, two RF transceivers for the data communication, and a personnel computer. Those fish tagged the pingers were tracked by the LBL method, and its location was calculated by the hyperbolic method. The average speed of the lsraeli carp was about 1.0 times of the body length in a farming water tank (24$\times$24$\times$1m), and the Red seabream 1.3 times of the body length in a farming raft (10$\times$10$\times$5m). A variation of the speed of the lsraeli carp was higher than the other one.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.1
• /
• pp.27-33
• /
• 1997

A neural network approach has been developed to determine the depth of a surface breaking crack in a steel plate from ultrasonic backscattering data. The network is trained by the use of feedforward three-layered network together with a back-scattering algorithm for error correction. The signal used for crack insonification is a mode converted 70$^{\circ}$transverse wave. A numerical analysis of back scattered field is carried out based on elastic wave theory, by the use of the boundary element method. The numerical data are calibrated by comparison with experimental data. The numerical analysis provides synthetic data for the training of the network. The training data have been calculated for cracks with specified increments of the crack depth. The performance of the network has been tested on other synthetic data and experimental data which are different from the training data.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.6
• /
• pp.703-710
• /
• 2012

A structural health monitoring technique for locating impact position in a composite plate is presented in this paper. The method employs a single sensor and spatial focusing properties of time reversal(TR) and inverse filtering(IF). We first examine the spatial focusing efficiency of both approaches at the impact position and its surroundings through impact experiments. The imaging results of impact localization show that the impact location can be accurately estimated in any position of the plate. Compared to existing techniques for locating impact or acoustic emission source, the proposed method has the benefits of using a single sensor and not requiring knowledge of anisotropic material properties and geometry of structures. Furthermore, it does not depend on a particular mode of dispersive Lamb waves that is frequently used in other ultrasonic testing of plate-like structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.111-117
• /
• 2011

Vibration monitoring is required for reliable thermosonic testing to decide whether sufficient vibration is achieved in each test for the detection of cracks. From a practical point of view, a cheaper and convenient monitoring method is better for the application to real tests. Therefore, the performance of different sensors for vibration monitoring was investigated and compared in this study to find a convenient and acceptable measurement method for thermosonics. Velocity measured by a laser vibrometer and strain provide an equivalent HI when measured at the same position. The microphone can provide a cheaper vibration monitoring device than the laser and the heating index calculated by a microphone signal shows similar characteristics to that calculated from velocity measured by the laser vibrometer. The microphone frequency response shows that it underestimates high frequency components but it is applicable to practical tests because it gives a conservative value of HI.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.2
• /
• pp.76-82
• /
• 1997

The discrimination of flaw shape and sizing is very important subject in the material evaluation for semiconductor and new materials. The aim of this paper is to investigate the spectrum analysis of artificial defect signal captured from steel ball embedded in the resin. The results show that it can be evaluated quantitatively the size of artificial defect, from the amplitude variation of same frequency if the probe with same diameter and focal length is used. Comparing with the amplitude variation of the high frequency component and low frequency component obtained from the distance of defect center position, it can be estimated steel ball and flat bottm defect.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.325-328
• /
• 2002

The partial-discharge(PD) is accompanied by physical and chemical phenomena, such as heat, light, noise, gas, chemical transformation, electric current, and electromagnetic radiation. The PD can be detected by measuring one of these changes. Although some techniques are employed in this purpose, several obstacles interfere with an on-line measurement. Now a fiber-optic sensor for detecting ultrasonics is suggested for the on line measurement system with high accuracy. In this paper, an optical fiber sensor utilizing the principal of Mach-Zehnder interferometer was proposed to detect the discharge signal.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.3
• /
• pp.38-46
• /
• 2005

The destructive method is reliable and widely used for the estimation of material degradation but it have time-consuming and a great difficulty in preparing specimens from in-service industrial facilities. Therefore, the estimation of degraded structural materials used at high temperature by nondestructive evaluation such as electric resistance method, replica method, Barkhausen noise method, electro-chemical method and ultrasonic method are strongly desired. In this study, various nondestructive evaluation(NDE) parameters of the Barkhausen noise method, such as MPA(Maximum Peak Amplitude), RMS, IABNS(Internal Area of Barkhausen Noise on Signal) and average amplitude of frequency spectrum are investigated and correlated with thermal damage level of 2.25cr-1.0Mo steel using wavelet analysis. Those parameters tend to increase while thermal degradation proceeds. It also turns out that the wavelet technique can help to reduce experimental false call in data analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.71-74
• /
• 2007

The objective of this presentation is to introduce a recent development of a magnetostrictive grating technique using an optimal yoke to efficiently generate and measure SH (Shear-Horizontal) waves in a plate. Gratings are effective means to generate frequency-tuned waves, but the gap between magnetostrictive gratings inevitably obstructs magnetic flow. Because magnetic field is the main physical quantity to actuate and sense ultrasonic waves, the transducer performance is most significantly influenced by the magnetic field distribution in the strips. Thus, wave transduction efficiency can be substantially improved if better magnetic flow is formed in the strips. To improve the efficiency, the topology optimization method was used to determine an optimal yoke configuration. A series of experiments on an aluminum plate were conducted using a grating with and without the designed yoke; when the yoke was used, the signal outputs increased up to 60 %.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1243-1246
• /
• 1987

To characterize the biological tissues, the new methods to measure the frequency dependent attenuation are presented in this paper. In general, ultrasonic phase information was assumed by linear function of the frequency. But, the minimum phase function which characterizes the frequency dispersion of tissue was derived in [l]. It is very significant to measure the attenuation by using the minimum phase function to characterize the frequency dispersion of tissue. Therefore, a more efficient method measuring the frequency dependent attenuation are proposed by using the estimated sound velocity and polarity of reflected signal. To verify the algorithms, pulse reflection experiments are performed.