• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.161-164
• /
• 2004

In this study, to develop the composition ceramics for the Ultrasonic vibrator, $Pb(Mn_{1/3}Nb_{2/3})O_3Pb(Zr.Ti)O_3$ system ceramics were manufactured as a function of PCN substitution. Its dielectric and piezoelectric characteristics were investigated. With increasing the amount of PCN substitution, electromechanical coupling factor(kp) were increased until 3mol% PCN and that after decreased. mechanical quality factor(Qm) showed the maxinum value at 2mol% PCN. Eletromechanical coupling factor, mechanical quality factor and dielectric constant were showed optimum value at PCN 2mol% as 0.58, 1630 and 1407, respectively for ultrasonic vibrator applications.

• 한국정밀공학회지
• /
• 제20권2호
• /
• pp.146-153
• /
• 2003

Ultrasonic inspection of defects has been focused on the existence of defect in structural material and need has much time and expenses in inspecting all the coordinates (x, y) on material surface. Neural networks can have an application to coordinates (x, y) of defects by multi-point inspection method. Ultrasonic inspection modeling is optimized by neural networks Neural networks has trained training example of absolute and relative coordinate of defects, and defect pattern. This method can predict coordinates (x, y) of defects within engineering estimated mean error $\psi$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.305-308
• /
• 2002

This paper presents design and analysis of stator which is vibration source of ring-type ultrasonic motor. The stator were designed for 9th flexural vibration mode. Designed stator was simulated by FEA for changing its materials. As results, the resonance frequencies of stators were changed by Poisson's ratio and density. And higher displacement were obtained by using the materials of low Young's modulus. Using the results, can easily design and manufacture the stator of ring type ultrasonic motor. And we suppose that it can save the time and finances.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.292-295
• /
• 2002

Transducer for linear ultrasonic motor with symmetric and anti-symmetric modes was studied. The transducer was composed of two Langevin-type vibrators that cross at right angles with each other at tip. In order to excite two vibration modes, two Langevin-type vibrators must have 90-degree phase difference with each other. As a result, tip of transducers moves in elliptical motion. In this paper, elliptical trajectory of transducer was analyzed by employing the finite element method.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.103-106
• /
• 2003

In this study, an ultrasonic transducer is fabricated with 1-3 type composite resonators. Pulse-echo responses of an ultrasonic transducer are investigated in underwater dependent on the variable designated water-level. LED Output signals of a level limit with changing a water level is obtained by the 1-3 type self-made composite transducer and electric measuring unit. LED is turned on at above the up-limit level with increasing a water level, and LED is turned on at less than the down-limit level with decreasing a water level. There was good agreement between the virtual water level and output LED signal by using the self-made water-detecting system.

• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.861-865
• /
• 1998

A plate-type linear ultrasonic motor using logitudinal and bending multi-vibration mode was designed and fabricated for the application to card-forwarding device. The stator consisted of PZ-PT-PMS piezoelectric ceramic plate and stainless steel. The performances of the motor were measured. As the experimental results, no-load speed of the motor was 0.6m/s when applied voltage was $80\textrm{V}_{rms}$ in resonance frequency. Starting torque was 1.4 mNm and maximum efficiency was 1.2%.

• 한국전기전자재료학회논문지
• /
• 제16권9호
• /
• pp.838-841
• /
• 2003

This paper shows results on the application of optical fiber sensors(OFS) for locations of ultrasonic signals in silicon insulating oil. The OFS system based on the principle of Sagnac interferometry has been designed and established for this work. The hollowed cylindrical mandrel wound by single mode optical fiber was used as a sensing component and ultrasonic signals which simulate the partial discharge In the oil have been generated by PZT actuator operated with function generator. The experimental results shows that the OFS has a excellent performance for the PD location with resolutions less than 1$^{\circ}C$ error range in the miniature insulating oil tank.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.415-418
• /
• 2000

In this paper, we calculated equivalent circuit of Langevin type ultrasonic vibrator and designed a vibrator whose resonant frequency is 50(KHz). FEA (Finite Element Analysis) was employed to calculate the resonant frequencies and maximum displacements of designed vibrators. The computer calculated resonant frequencies were approached to the designed one. As AC voltage input the maximum displacements were shown sinusoidal changes. Terminal input admittance over a frequency range spanning the resonant frequency were calculated. ANSYS was employed to calculate resonant frequencies, displacements and terminal input admittance of vibrators

• 한국전기전자재료학회논문지
• /
• 제30권8호
• /
• pp.496-500
• /
• 2017

$Pb(Mn_{1/3}Nb_{2/3})_{0.07}(Ni_{1/3}Nb_{2/3})_{0.10}(Zr_{0.5}Ti_{0.5})_{0.83}O_3$ composition ceramics with high piezoelectric properties were fabricated by the columbite precursor method for ultrasonic generators, and the effects of sintering temperature on microstructure and piezoelectric properties were systematically investigated. It was found that the tetragonality of the ceramics decreased with increase in sintering temperature. Moreover, excellent physical properties such as $d_{33}=447pC/N$, ${\varepsilon}_r=1,843$, $k_p=0.641$, and $Q_m=1,207$ were obtained for an ultrasonic generator when the second calcination temperature and sintering temperature were $720^{\circ}C$ and $920^{\circ}C$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.292-295
• /
• 2003

In this study, an ultrasonic transducer is fabricated with 1-3 type composite resonators. Pulse-echo responses of an ultrasonic transducer are investigated in underwater dependent on the variable designated water-level. LED Output signals of a level limit with changing a water level is obtained by the 1-3 type self-made composite transducer and electric measuring unit. LED is turned on at above the up-limit level with increasing a water level, and LED is turned on at less than the down-limit level with decreasing a water level. There was good agreement between the virtual level and output LED signal by using the self-made water-detecting system.