• 한국재료학회지
• /
• 제13권10호
• /
• pp.651-657
• /
• 2003

Ultrasonic microscope has been used to detect the defects on surface or inner solid. Conventionally, it has used at a single operating frequency. The resolution and quality of the measured images are determined by a characteristic of the transducer of the ultrasonic microscope. The conventional ultrasonic microscope has been used envelope detector to detect the amplitude of reflected signal, but the changes in amplitude is not sensitive enough for specimen with microstructure that in phase. In this paper, we have studied multi-frequency depth resolution enhancement with ultrasonic reflection microscope for the reflectors of a stainless steel reference specimen and a reference calibration block to be used as the material in nuclear power plants for ISI, PSI. Increased depth resolution can be obtained by taking two, three-dimensional images at more that one frequency and numerically combining the results. As results of the experiment, we could get enhanced images with the rate of contrast in proportion and high quality signal distribution for the image to the changing rate of depth for the reflectors of the two kinds of specimens.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1518-1520
• /
• 2002

Purpose of this research compares best transfer speed about applied frequency and voltage using characteristic of $L_1-B_4$ mode and $L_1-B_8$ mode linear ultrasonic motor that use piezoelectric effect. By method of study, analyzed best transfer speed measuring and comparison load status that use actuality telephone card in $L_1-B_4$ mode linear ultrasonic motor and no-load status of $L_1-B_8$ mode linear ultrasonic motor. Experiment result is applied frequency(58.4Hz) in $L_1-B_4$ mode linear ultrasonic motor (load state) and the best transfer speed by 19.8[cm/s] at applied voltage(56V) point. Also, $L_1-B_8$ mode linear ultrasonic motor (no-load state) is best transfer speed by applied frequency(27.9kHz) and 32.96[cm/s] at applied voltage (50V) point.

• 한국음향학회지
• /
• 제15권1호
• /
• pp.10-16
• /
• 1996

압전초음파모터는 기존의 전자기식모터와는 달리 압전전체가 발생하는 초음파진동에 의한 마찰력으로 회전자의 구동력을 얻는 모터이다. 이는 구조가 간단하고, 저속에서 높은 토오크를 얻을 수 있어 감속기구 없이 직접구동이 가능한 장점이 있어 주목을 받고 있다. 그러나 이 모터는 인가주파수, 인가전압, 2상의 구동신호사이의 위상차 및 구동신호의 duty비 등에 따라 그 특성이 변하므로, 모터를 제어하기 위해서는 이러한 변수들에 대해 정밀한 특성측정이 필요하다. 본 연구에서는 초음파모터의 제작과 함께 컴퓨터인터페이스된 압전초음파모터 평가장치를 개발하였고, 제작한 초음파모터의 특성을 여러 구동변수에 대해 측정하였다. 구동변수들은 모두 디지털로 처리되므로, 초음파모터의 특성측정을 쉽게 할 수 있을 뿐만 아니라, 차후 초음파모터의 디지털제어에 기본 바탕이 된다.

• 비파괴검사학회지
• /
• 제31권2호
• /
• pp.174-180
• /
• 2011

본 연구에서는 초음파원자현미경을 이용하여 비파괴적인 표면탄성이미지 분석과 나노표면에서의 기계적 물성 평가를 연구하였다. 이를 위해 접촉역학 특성에 따른 캔틸레버의 공진주파수 변화를 이론적으로 해석하고 실험적으로 측정하였다. 스프링-질량 모델과 Herzian 이론을 이용하여 계산한 이론적인 접촉공천주파수는 초음파원자현미경 캔틸레버의 실험적인 접촉 공진주파수의 변화와 매우 유사하였다. 결과적으로, 초음파원자현미경의 표면 높이 이미지와 진폭이미지를 성공적으로 얻을 수 있었고 진폭신호를 통하여 시료표면에서의 탄성특성을 정성적으로 평가하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술회의 초록집
• /
• pp.2-4
• /
• 2010

Nowadays, application fields using piezoelectric ceramics are various. On this paper, Characteristics of thin-type ultrasonic motor generating elliptical displacements has been analyzed by FEM, and then the motor was fabricated. Structure of the motor consists of sixteen ceramic pieces attached elastic body upper and bottom. Principle of the motor is to apply alternative voltages which have 90 phase difference to attached ceramics, and then elliptical displacements is generated at four edges of clastic body. And then rotor is rotated by the elliptical displacements. In case of ceramic thickness 1.5[mm], characteristic of the highest speed was found at 79[kHz]. In case of ceramic thickness 2[mm], Characteristic of the highest speed was observed at 77.5 [kHz]. Consequently, speed and torque of USM were increased linearly with increasing in applied voltage.

• 한국기계가공학회지
• /
• 제13권6호
• /
• pp.119-126
• /
• 2014

Micro-holes of conductive ceramic are required in micro structures. Micro-electrical discharge machining (Micro-EDM) is an effective machining method since EDM is as process for shaping hard metals and complex-shaped holes by spark erosion in all kinds of electro-conductive materials. However, as the depth of micro hole increases, the machining condition becomes more unstable due to inefficient removal of debris between the electrode and the workpiece. In this paper, micro-EDM was performed to evaluate machining characteristic such as electrode wear, machining time, taper angle, radial clearance with varying voltage and ultrasonic vibration on 10 vol.% Carbon-nanotube reinforced conductive $Al_2O_3$ composite fabricated by spark plasma sintering in previous research.

• 비파괴검사학회지
• /
• 제19권3호
• /
• pp.207-216
• /
• 1999

일반적인 하나 또는 두개의 압전소자를 사용하는 트랜스듀서에 비하여 다수의 압전소자를 사용하는 어레이 트랜스듀서는 각 압전소자에 가해지는 펄스의 지연시간을 제어함으로써 초음파 빔을 임의의 지점에 집속시킬 수 있고 기계적 구동없이 임의의 방향으로 조향시켜 실시간 주사를 할 수 있는 장점이 있다. 페이즈드 어레이 트랜스듀서의 설계조건은 압전소자의 수. 압전소자의 크기 그리고 압전소자 사이 간격 등 여러가지가 있으며, 본 연구에서는 그 중에서 압전소자수의 변화에 따른 초음파 빔의 특성을 호이겐스의 원리를 이용한 수평횡파의 시뮬레이션을 통하여 평가하였다. 그 결과 초음파 빔은 조향각이 증가 할수륵 음압이 감소하며, 초음파 빔 특성도 점차적으로 분산됨을 알 수 있었고 또한, 초점거리가 증가할수록 초점에서의 집속효과는 감소하고, 압전소자의 수가 증가되면 집속효과는 향상됨을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.597-599
• /
• 1996

This paper describes the bending traveling-wave type ultrasonic motor which generates the traveling wave by combining two standing waves with phase difference time and space. In $+20^{\circ}C{\sim}30^{\circ}C$, the USM motor operation character has represented normal condition. But the other temperature, (that is say, when long time operating condition) USM operation characteristic has abnormal condition, that is driving frequency, drive current and r.p.m is down. The recent USM has controller without temperature compensation. This study aimed at fuzzy controller which must follow the frequency at operation temperature and then r.p.m and torque increase.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1996년도 창립기념 전력전자학술발표회 논문집
• /
• pp.52-55
• /
• 1996

This paper describes the bending traveling-wave type ultrasonic motor which generates the traveling wave by combining two standing waves with phase difference time and space. In $+20^{\circ}C$~$30^{\circ}C$, the USM motor operation character has represented normal condition. But the other temperature, (that is say, when long time operating condition) USM operation characteristic has abnormal condition, that is driving frequency, drive current and r.p.m is down. The recent USM has controller without temperature compensation. This study aimed at fuzzy controller which must follow the phase angle difference 90$^{\circ}$at operation temperature and them r.p.m and torque increase.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.441-444
• /
• 1997

This paper describes the bending traveling-wave type ultrasonic motor which generates the traveling wave by combining two standing waves with phase difference time and space. In +2$0^{\circ}C$~3$0^{\circ}C$, the operation characteristic of USM has represented normal condition. But in the other temperature, the operation characteristic of USM has abnormal condition, that is driving frequency, drive current and r.p.m are down. The recent USM has controller without temperature compensation. This study aimed at fuzzy controller which must follow the frequency at operation temperature and then r.p.m and torque increased.