• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.37-41
• /
• 2007

Recently PZT is used in ultra precision mechanism field. PZT has a small motion range although it has a high resolution. Many methods, such as inchworm, impact driving, etc., have been applied for the expansion of the motion range.? In this study, the new actuating mechanism for rotational motion with two PZT actuators is proposed. The ultra precision rotational actuator which is made by proposed mechanism is able to operate both coarse and fine motion. The design parameters of the proposed mechanism are considered to improve the performance of the system. The rotational stage which is applied by the proposed mechanism is fabricated. The resolution and velocity for fabricated rotational stage are measured by laser interferometer.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2386-2388
• /
• 2005

As anti-crash and pre-crash systems in vehicles become more extensively used, the need for high performance short-range radars is playing an increasing role. This paper presents the design of a micromachined, ultra-wideband beamformer centered at 24 GHz for automotive short-range radar systems. This beamformer is a Butler matrix designed using ultra-wideband transmission-line couplers, which consist of a multilayered structure that exhibits wider bandwidth compared to conventional microstrip branch-line couplers. The circuit has been designed on a quartz substrate, and to achieve the desired coupling, lines suspended on BCB layers located at specific parts of the circuit were used, achieving a three metal layered structure in form of wide microstrips, that give low loss and a wideband response. In this paper the design and fabrication procedure of the proposed beamformer are fully described.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.152-157
• /
• 1998

Since early 1960s, the high precision machining technology, so called ultra-precision technology or nano technology, has been developed in many Held based on single point diamond turning technology. The major application of this technology is the optical components with aspherical surfaces. Now a days, customer requires the smaller and lighter optical elements, such as camera video and etc., with higher performance for convenience. So, the manufacturer focuses on the ultra-precision technology. Thus, this technology becomes the major target to challenge the advanced barrier for the next machining technology.

• ETRI Journal
• /
• v.45 no.3
• /
• pp.534-542
• /
• 2023

The large amount of secondary effects in complementary metal-oxide-semiconductor technology limits its application in the ultra-nanoscale region. Circuit designers explore a new technology for the ultra-nanoscale region, which is the quantum-dot cellular automata (QCA). Low-energy dissipation, high speed, and area efficiency are the key features of the QCA technology. This research proposes a novel, low-complexity, QCA-based one-bit digital comparator circuit for the ultra-nanoscale region. The performance of the proposed comparator circuit is presented in detail in this paper and compared with that of existing designs. The proposed QCA structure for the comparator circuit only consists of 19 QCA cells with two clock phases. QCA Designer-E and QCA Pro tools are applied to estimate the total energy dissipation. The proposed comparator saves 24.00% QCA cells, 25.00% cell area, 37.50% layout cost, and 78.11% energy dissipation compared with the best reported similar design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.4
• /
• pp.76-86
• /
• 2019

The cross-flow turbine is a key hydraulic power system that is widely due to low costs, high efficiency, and low maintenance. In particular, the cross-flow turbine considered as the most suitable turbine for low head situations as it is known to operate down to 5 m of water head. However, the conventional cross-flow turbine is unsuitable for ultra-low head situations with less than a 3 m water head. In this study, we propose an inverted-type cross-flow turbine to overcome the limitations of conventional cross-flow turbines under ultra-low head situations. First, we described the limitations of conventional turbines and suggested a new turbine for the ultra-low head circumstances. Second, we investigated the performance of the new turbine using CFD analysis. Results demonstrated the effects of the design parameters, such as number of blades and rotor diameter ratio, on the performance of the suggested turbine. As a result, we developed an inverted-type cross-flow turbine with up to 60% efficiency under low water head conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.76-83
• /
• 2021

This study examines the bending behavior of lap-spliced ultra-high-strength fiber-reinforced concrete members and evaluates the safety of the design codes for ultra-high-strength fiber-reinforced concrete structures. An experiment on a total of six beams was performed. The main variables were the fiber-inclusion and the lap-spliced length at the center of the beams. The steel fibers in a volume fraction of 2% were used, and the lap-splice lengths were determined to be 8db and 16db. As a result of the test, the specimens not reinforced with fiber lost abrupt load-bearing capacity at the lap region and did not experience yielding of the reinforcing bar. In the case of fiber-reinforced concrete, if a lap-splice length of 16db is secured, the yielding of the main reinforcing bar can be experienced, and appropriate flexural strength can be expressed. Based on the experimental results of this study, as a result of reviewing the lap-splice length calculation formulas of the current design standards and the ultra-high-strength concrete structural design recommendations, it was found that all of them were evaluated conservatively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.7
• /
• pp.18-22
• /
• 2010

In this paper, we propose and analyze the two way ranging (TWR) positioning technique using ultra wideband (UWB) for indoor environment. We employed IEEE 802.15.3a channel as a simulation environment and used to time of arrival (TOA) algorithm. UWB technology in a low transmission power the less the effect of interfering with the existing system, the frequency can be shared so that it can improve the spectral efficiency. And, positioning technique based on UWB with a very narrow pulse width has high accuracy in indoor environment. From the simulation results, it is analyzed the probability of error and positioning performance for channel effects and confirmed usefulness of the proposed scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.12
• /
• pp.1267-1271
• /
• 2012

Demand for optical glass device used for lighting could increase rapidly because of LED lighting market growth. The optical glass devices that have been formed by hot press molding process the desired optical performance without being subjected to mechanical processing such as curve generation or grinding. EL-Max material has been used for many engineering applications because of their high wear resistance, high compressive strength, corrosion resistant and very good dimensional stability. EL-Max is very useful for a glass lens mold especially at high temperature and pressure. The performance and reliability of optical components are strongly influenced by the surface damage of EL-Max during grinding process. Therefore, the severe process condition optimization shall be necessary for the highly qualified EL-Max glass lens mold. To get the required qualified surface of EL-Max, the selection of type of the diamond wheel is also important. In this paper, we report best grinding conditions of ultra-precision grinding machining. The grinding machining results of the form accuracy and surface roughness have been analyzed by using Form Talysurf and NanoScan.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1249-1255
• /
• 2010

An ultra high- pressure system generally consists of a hydraulic power unit, an oil supply unit, an electrical power supply device, and an electrical control device. The hydraulic power unit supplies the hydraulic power to the intensifier to create generate ultra high pressure. The intensifier amplifies increases the pressure using the oil supplied from by the hydraulic power unit. The electrical supply devices and control devices maintain are provided for the electric motors, valves, and sensors. In this study, instead of a flow-control device, a pressure-control type device was mounted on a manifold block in the hydraulic power unit instead of the flow-control type. A servo valve was fitted in the intensifier, and the performance characteristics of the intensifier varied according to the variations of in the pressure cycle and with the temperature of the operating oil in the hydraulic power unit.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.10
• /
• pp.1197-1205
• /
• 2014

Recently signal transmission of ultra high-definition(4K-UHD) video system is transferred as uncompressed high speed data. However, this has a limit to compose the system because EMI between separate cables of high speed interface section and skew bring distortion of the video signal and jitter. In this paper we applied V-by-One HS interface technique to transfer uncompressed high speed data. We analyzed HSD(High Speed Differential) transmission line signal integrity. Also we applied RF transmission technique instead of UHD video pattern control interface PCB design. When we measured V-by-One HS video signal of designed 4K-UHD class signal generator, We found that the transmission performance has been signal standard.