• 한국정밀공학회지
• /
• 제32권11호
• /
• pp.983-988
• /
• 2015

This paper details a new ultra-precise turning method for increasing surface quality, "Multi Point B Axis Control Method." Machined surface error is minimized by the compensation machining process, but the process leaves residual chip marks and surface roughness. This phenomenon is unavoidable in the diamond turning process using existing machining methods. However, Multi Point B axis control uses a small angle (< $1^{\circ}$) for the unused diamond edge for generation of ultra-fine surfaces; no machining chipping occurs. It is achieved by compensated surface profiling via alignment of the tool radial center on the center of the B axis rotation table. Experimental results show that a diamond turned surface using the Multi Point B axis control method achieved P-V $0.1{\mu}m$ and Ra 1.1nm and these ultra-fine surface qualities are reproducible.

• 소성∙가공
• /
• 제19권8호
• /
• pp.474-479
• /
• 2010

Newly suggested hybrid LED package can reduce the number of LED processes and enhance light efficacy in virtue of its integrated optical patterns. Square-type pyramid pattern was chosen for the integrated optical pattern in this study, and it was proved that the pattern enhances illuminance about three times and luminance about two and half times by optical simulation. Square-type pyramid patterns of 0.02mm height and 0.04mm pitch were successively machined on a copper mold which is necessary for imprinting the integrated pattern. Hybrid LED package with integrated optical pattern will be manufactured with ultra-fine machined mold in future study.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.58-63
• /
• 1999

Almost all concrete structures have many inevitable cracks for various reasons such as drying shrinkage, heat liberation of cement, fatigues or repeating loads and movements. Conventionally, they are repaired with epoxy materials. The Epoxy resins used by repair materials are different from properties of the base concrete materials such as thermal and mechanical properties - thermal expansion coefficients, bending strength. And the epoxy resin cannot release the water inside the concrete structure and cause corrosion of the steel bars. In this study, before the experiment got launched, we had analyzed cement and slag. Then We blended the two grades of ultra fine cement using high blaine cement and slag. And the cement slurry was produced by water and suprplasticizer to each blended ultra fine cement in various conditions. The slurry produced by each conditions was evaluated with flow properties such as viscosity, dropping time, segregation and observation of dry surface after injection.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.351-352
• /
• 2009

On-demand ejection of ultra-fine droplets that uses both electrohydrodynamic (EHD) force and mechanical actuation is presented. The liquid meniscus was controlled by a piezoelectric actuator and droplets were ejected by EHD force. Through these effects, it was possible to obtain a high operational jetting frequency of 5kHz with a short delay-time (about 50 us) when compared with existing on-demand EHD jetting methods, such as the pulsating jet mode (3-10 msec) and the pulsed-voltage cone-jet mode(3.6 msec). Also, we obtained ultra-fine droplets at a volume that was at the femto-liter level simultaneously. The jetting characteristics were examined for both hydrophobicity and hydrophilicity of the surface of a capillary.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.13-14
• /
• 2006

The quality of tool material is very important factor in machining evaluation. The characteristics of tungsten carbide, such as grain size and hardness, and density are depending on the variation of Co composition and WC size. In this study, the non-coated end mill which is made of ultra-fine tungsten carbide is investigated by measuring tool wear and tool lift test. The machining test is conducted with high hardened workpiece under high-speed cutting condition.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1323-1324
• /
• 2006

Refractory materials, such as W and Mo, are very useful elements for use in high-temperature applications. But it is not easy to fabricat pure W and Mo with very high density and retaining very fine grain size because of their high melting point. In this paper, a newly developed method named as resistance sintering under ultra high pressure was use to fabricate pure fine-grained W and Mo. The microstructure was analysis by SEM. The sintering mechanism is primary analyzed. Basic physical property of these sintered pure W and Mo, such as hardness, bend strength, are tested.

• 동아시아식생활학회지
• /
• 제4권2호
• /
• pp.45-49
• /
• 1994

The rapid preparaton method of soybean curd with ultra fine soy powder at home was investigated. The microwave oven of this study used common microwave attached sensor for the volume and temperature control, The temperature of the microwave oven was maintained at 98, not boiling over. It took 9 minutes to make 300g of soybean curd, 10 minutes to make 600g, 14 minutes to make 900g, and 17 minutes to make 1200g. Beany flavor and trypsin inhibitor could be removed by this conditon. It took only 5 min to make coaguation of the curd by glucono-$\delta$-lactone.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.1095-1100
• /
• 2000

Concrete structure often exhibit cracks due to the combination of material construction and design error. Minor crack can be tolerated depending on exposure condition, but major cracks are aesthetically unpleasant and affect the durability and safety of the structure. All of the reinforced concrete structure have many inevitable cracks for various reason such as drying shrinkage, heat liberation of cement and over loads. Epoxy resin injection widely used for repairing cracks in concrete is too sensitive to high temperature. Besides, the problem in the epoxy resin injection is the difficulty of quality control after execution. Whereas, Ultra Fine Cement is similar in coefficient of thermal expansion and modulus of elasticity to concrete. The objective of the study is to find out that it is possible for Ultra Fine Cement to be used for repairing cracks in reinforced concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.757-760
• /
• 2006

This study aims to manufacture ultra fine cement(UFC) with a multi air-classifier of the dry-type. The classifier employed and devised for materials refining was a cyclone type fitted with an air suction device. This study also investigates the basic physical properties and quality of UFC and evaluates its utilizable possibility as a construction material. The basic properties of the UFC containing granulated blast furnace slag were analyzed and examined through recovery ratio, particle size distribution, scanning electron microscopy and compressive strength. Results obtained from the analysis of ultra fine cement have shown that there are possibilities for manufacturing UFC, which could compensate the weak properties of ordinary Portland cement.

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.101-110
• /
• 2013

PURPOSES : The purpose of this study is to evaluate the durability of ternary blended concrete mixtures adding ultra fine admixture. METHODS : From the literature review, crack was considered as the main distress failure criterion on concrete bridge deck pavement. To reduce the initial crack development due to drying shrinkage, CSA expansion agent and shrink reduction agent were used to ternary blended concrete mixtures as a admixture. Laboratory tests including chloride ion penetration test, surface scaling test, rapid freeze & thaw resistance test, non restrained drying shrinkage and restrained drying shrinkage test were conducted to verify the durability of ternary blended concrete mixtures. RESULTS : Based on the test results, proposed mixtures were verified as high qualified durable materials. Expecially initial drying shrinkage crack was not occurred in ternary blended concrete mixtures with CSA expansion agent. CONCLUSIONS : It is concluded that the durability of proposed ternary blend concrete mixture was acceptable to apply for the concrete bridge deck pavement.