• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.358-365
• /
• 2008

A differential-gain-controlled LNA is designed and implemented in 0.18 um CMOS technology for $3.1{\sim}4.8GHz$ UWB system. In high gain mode, measurements show a differential power gain of $14.1{\sim}15.8dB,\;13.3{\sim}15dB$, respectably, an input return loss higher then 10dB, an input IP3 of -19.3 dBm, a noise figure of $4.85{\sim}5.09dB$, while consuming only 19.8 mW of power from a 1.8V DC supply. In low gain mode, measurements show a differential power gain of $-6.1{\sim}-4.2dB,\;-7.6{\sim}-5.6dB$, respectably, an input return loss higher then 10dB, an input IP3 of -1.45 dBm, a noise figure of $8.8{\sim}10.3dB$, while consuming only 5.4mW of power from a 1.8V DC supply.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.1
• /
• pp.42-52
• /
• 2012

In this paper, a waveguide antenna is designed and fabricated for side and rear radar sensor of vehicles in UWB (Ultra Wide Band) high band (center frequency : 9.5 GHz, -10 dB bandwidth : 600 MHz (6.4 %)). For the radar antenna, a probe fed rectangular waveguide antenna having simple structure and wide bandwidth is used. An important performance factor in this antenna is the isolation between transmitting (TX) and receiving (RX) waveguide antennas because this radar system uses TX and RX antennas separately. Thus the isolation between two antennas was simulated for E-plane and H-plane array. As a result, it was verified that the isolation of the H-plane array of the antennas is better than E-plane array, due to the TE10 mode. Therefore, H-plane arrayed waveguide antennas were mounted on a T-shaped radar module and performance of antennas was investigated. The -10 dB bandwidth of the TX and RX antenna mounted on T-shaped radar module was measured as 1000 MHz (10.52 %) and 1090 MHz (11.47 %) respectively and the isolation is less than -50 dB in the operation band. The peak gain is 7.65 dBi for the TX antenna and 7.26 dBi for the RX antenna and the beamwidth of H-plane of TX and RX antenna was measured as $64^{\circ}$ and $65^{\circ}$ respectively. Consequently, we verified that the proposed waveguide antenna is appropriate for a vehicle radar applications.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.11
• /
• pp.5527-5545
• /
• 2019

Through-wall ultra-wide band (UWB) radar has been considered as one of the preferred and non-contact technologies for the targets detection owing to the better time resolution and stronger penetration. The high time resolution is a result of a larger of bandwidth of the employed UWB pulses from the radar system, which is a useful tool to separate multiple targets in complex environment. The article emphasised on human subject localization and detection. Human subject usually can be detected via extracting the weak respiratory signals of human subjects remotely. Meanwhile, the range between the detection object and radar is also acquired from the 2D range-frequency matrix. However, it is a challenging task to extract human respiratory signals owing to the low signal to clutter ratio. To improve the feasibility of human respiratory signals detection, a new method is developed via analysing the standard deviation based kurtosis of the collected pulses, which are modulated by human respiratory movements in slow time. The range between radar and the detection target is estimated using joint time-frequency analysis (JTFA) of the analysed characteristics, which provides a novel preliminary signature for life detection. The breathing rates are obtained using the proposed accumulation method in time and frequency domain, respectively. The proposed method is validated and proved numerically and experimentally.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.12
• /
• pp.1765-1767
• /
• 2016

Non-coherent UWB receivers are promising due to the low hardware complexity while the coherent receiver such as the rake receiver requires the complex hardware to estimate channel characteristics and get the synchronization. In this letter, the block coded modulation scheme as one of the most promising method is enhanced in terms of the performance. The performance enhancement is carried out by the modification of the block structure with unequal frame length for each pulse. Simulation results show that the proposed method has the performance enhancement by the transmission rate or bit error rate.

• ETRI Journal
• /
• v.30 no.4
• /
• pp.526-534
• /
• 2008

This paper presents a fully integrated 0.13 ${\mu}m$ CMOS MB-OFDM UWB transmitter chain (mode 1). The proposed transmitter consists of a low-pass filter, a variable gain amplifier, a voltage-to-current converter, an I/Q up-mixer, a differential-to-single-ended converter, a driver amplifier, and a transmit/receive (T/R) switch. The proposed T/R switch shows an insertion loss of less than 1.5 dB and a Tx/Rx port isolation of more than 27 dB over a 3 GHz to 5 GHz frequency range. All RF/analog circuits have been designed to achieve high linearity and wide bandwidth. The proposed transmitter is implemented using IBM 0.13 ${\mu}m$ CMOS technology. The fabricated transmitter shows a -3 dB bandwidth of 550 MHz at each sub-band center frequency with gain flatness less than 1.5 dB. It also shows a power gain of 0.5 dB, a maximum output power level of 0 dBm, and output IP3 of +9.3 dBm. It consumes a total of 54 mA from a 1.5 V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.1C
• /
• pp.113-119
• /
• 2009

The training sequence with the appropriate length for equalization and initial synchronization is necessary before sending the pure data in the burst transmission type DS-UWB system. The length of the training sequence is one of the factors which make throughput decreased. The noble structure with the variable length of the training sequence whose length can be adaptively tailored according to the channel conditions (CM1,CM2,CM3,CM4) in the DS-USB systems is proposed. This structure can increase the throughput without sacrificing the performance than the method with fixed length of training sequence considering the worst case channel conditions. Simulation results under IEEE 802.15.3a channel model show that the proposed scheme can achieve higher throughput than a conventional one with the slight loss of BER performance. And this structure can reduce the computation complexity and power consumption with selecting the short length of the training sequence.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.4
• /
• pp.43-49
• /
• 2013

In this paper, it is designed inverted triangle structural planar monopole antenna with edge and rectangle slot for UWB(Ultra Wide Band) communication (3.1~10.6 GHz) and researched in about 5.8 GHz notch structure to prevent interference between UWB systems and existing wireless systems for using Wi-Fi service. The antenna have broadband property structurally through inverted triangle structural planar monopole which have edge. and rectangle form addition planned notch slot of 1 mm and height 0.1 mm. Monopole and ground of proposed antenna exist on coplanar plane, and excite as CPW. It used FR4 epoxy dielectric substrate of ${\varepsilon}r$=4.4, and the size is $20{\times}20{\times}1.6$ mm dimension. The measured results that are obtained return loss under -10 dB through 3.1~10.6 GHz(7.5 GHz) without Wi-Fi bandwidth and maximum gain of 8.44 dBi at E-plane. Radiation pattern is about the same that of dipole antenna at all frequency. And using notch slot and it will be able to confirm the quality which becomes notch from 5.8 GHz which are a radio LAN frequency range.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.117-122
• /
• 2006

A CMOS LNA based on a single-stage cascode configuration is designed for MB-OFDM ultra-wide band(UWB) systems. Wideband($3.1GHz\~4.9GHz$) input matching is performed using a simple bandpass filter to minimize the chip size and the noise figure degradation. The simulation results using $0.18{\mu}m$ CMOS process parameters show a power gain of 9.7dB, a 3dB band width of $2.1GHz\~7.1GHz$, a minimum NF of 2dB, an IIP3 of -2dBm. better than -11.8dB of input matching while occupying only $0.74mm^2$ of chip area. It consumes 25.8mW from a 1.8V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11B
• /
• pp.792-803
• /
• 2005

Ultra wide band (UWB) technology will be applied in the high rare wireless personal area networks (WPANs) for its high rate, low power, and innate immunity to multipath fading. In this paper, a power aware multi-hop packet relay MAC protocol in UWB based WPANs is proposed and a power aware path status factor (PAPSF), which is derived from SINR and power resource condition of each device, is used to select a suitable relay node. Compared with relaying by piconet coordinator (PNC), which is easily chosen by other ad hoc routing protocol, the new scheme can achieve hi임or throughput, decrease the time required for transmitting high power signal and we can easily distribute the battery power consumption from PNC to other devices in the piconet to prevent the PNC device using up its battery too fast and finally avoid PNC handover too frequently.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1121-1129
• /
• 2009

In this paper, the UWB(Ultra-Wide Band) modules such as a pulse generator and the LNA(Low-Noise Amplifier) with AGC(Auto Gain Control) are designed to construct a cross-borehole pulse radar system, of which performance is compared with the existing system. The budget and specification of the radar system are determined by calculating the total path loss of the underground medium including an empty cavity. The pulse generator is fabricated to have the repeatation frequency 40 kHz, the pulse width lower than 5 ns and the peak signal level +73 dBm. The UWB LNA is designed to have the noise figure 3.77 dB, the variable gain range 100 dB and the frequency range of 20 MHz to 200 MHz. Compared with the existing system in an actual test site, the implemented system renders it possible to detect the blind area due to the UWB LNA with low noise figure.