• Journal of Technologic Dentistry
• /
• v.44 no.3
• /
• pp.76-80
• /
• 2022

Purpose: The purpose of this study is to analyze the depth according to curing using photocurable resin for dental three-dimensional printing. Methods: A stainless mold with a height of 4 mm was prepared. Ultraviolet (UV) polymerization resin was injected into the mold. Photocuring was then performed for 5 minutes using a photopolymerizer, and the height was measured using a digital measuring instrument (first group). Second, light polymerization was also performed outside the mold for 5 minutes, and the height was measured using a digital measuring instrument. Third, light polymerization was further performed for 5 minutes, and the height was measured using a digital measuring instrument. Statistical analysis was performed with the Kruskal-Wallis test, which is a nonparametric test (α=0.05). Results: The third group had the largest measurement length, whereas the first group had the smallest. However, the difference between groups was not statistically significant (p>0.05). The color of the first group was different from that of the second and third groups. Conclusion: All of the 4-mm-thick photocured specimens had a curing reaction, but the part that was not directly irradiated with UV did not show its original color.

• Clean Technology
• /
• v.16 no.4
• /
• pp.245-253
• /
• 2010

Optimum conditions for UV-radiated photopolymerization of unsaturated polyester that could be used as protecting layer of large diameter pipe were investigated in this paper. UV photopolymerization method was selected to solve the problems, arising when thermal polymerization by organic peroxide was used, such as the instability of peroxide initiator, the evolution of volatile organic compound, and thermal deformation of product. Two of the photo-initiators (Irgacure 819 and Darocure 1173) well known for its penetrating ability deep into the polymer layer were selected, and the optimum conditions for photopolymerization (1.5 phr initiator content, 1:1.2 initiator ratio, Ga lamp for UV source) were found from the thermal and mechanical test results of the resultant UP polymers. In addition, composite materials containing UP polymer and glass fiber were tested for hardness, impact strength, and flexural strength to find that the impact strength of composite significantly improved.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2005.05a
• /
• pp.112-115
• /
• 2005

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.902-906
• /
• 1999

Electrically conducting composite films were prepared by a vapor phase in situ polymerization of pyrrole in the methyl cellulose film containing a copper(II) perchlorate. Methylcellulose had high affinity to pyrrole and was used as a matrix polymer. Conducting polypyrrole was embedded in the methylcellulose film forming a conducting network and the conductivity of the composite films ranged $10^{-1}$ to $10^{-7}S/cm$. The conductivities of conducting composite films were dependent on the nature of the matrix polymers, concentration of oxidant and polymerization time. In situ polymerization of pyrrole was observed in the matrix polymer and confirmed by UV-vis spectra. From the results of the thermogravimetric analysis, the chemical oxidative polymerization of pyrrole in the matrix polymers did not give any negative effects on the thermal stability of the composite films. Electron micrograph of composites indicated good penetration of PPy in the matrix polymer. DMA suggested a certain degree of incompatibility of the polypyrrole in the composites.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.11 no.1
• /
• pp.45-55
• /
• 1993

• Textile Coloration and Finishing
• /
• v.24 no.2
• /
• pp.97-105
• /
• 2012

Compared with conventional adsorption-based coloration, the photoreactions of dyes such as photo-copolymerization and photo-crosslinking under UV irradiation can be employed for the coloration of textiles, which can be carried out without salt addition at room temperature. C.I. Reactive Black 5, a homo-bifunctional reactive dye containing two sulfatoethylsulfone groups, is used as a photo-reactive dye for wool fibers. Upon UV irradiation, the photo-reactive dye was grafted onto wool fabrics without photoinitiators. Since the disulfide bonds in the cystine residues of wool can be easily photodecomposed to active thiyl radicals which initiate the polymerization, the dye can be polymerized to an oligomeric dye of a degree of polymerization of 12 or more. The grafted fabrics reached a grafting yield of 2.3% o.w.f. and a color yield (K/S) of 18.2 by the photografting of an aqueous dye concentration of 9% using a UV energy of 25J/$cm^2$. Furthermore, the photochemically dyed wool fabric showed higher colorfastness properties to light, laundering and rubbing comparable to conventional reactive dyeing.

• Analytical Science and Technology
• /
• v.17 no.3
• /
• pp.225-229
• /
• 2004

The effect of the silicon acrylate as a reactive additive on the UV-curing photopolymerization reaction was studied by micro raman technique. For the study, acrylate systems and Darocur 1173 were used as oligomer and monomers, and a photo initiator, respectively. The content of silicon acrylate was within the range of 0-3 wt%. The extent of photo-polymerization reaction as a function of depth from the air interface was obtained from the conversion ratio of acrylate double bond calculated from the intensities of measured bands at $1410cm^{-1}$ and at $1635cm^{-1}$. Micro raman spectroscopic technique can be an useful tool for the investigation of the factors, which can affect the reaction progress, such as oxygen inhibition, composition of the formulations, depth, etc.

• Journal of the Korean Chemical Society
• /
• v.55 no.1
• /
• pp.98-103
• /
• 2011

This study was done for the preparation of macromolecular material with UV-blocking features by adding the benzophenone group that is commonly used as a UV-absorbent and $TiO_2$ which is known to be a very stable material in chemical and physical aspects. Also, we compared the level of UV absorbency of the polymer produced from polymerization with previous materials and measured basic properties such as water content, refractive index and optical transmittance of produced contact lenses. The results of the measurement showed that the refractive index and water content of the contact lens with added UV-absorbent was 1.430~1.440 and 35.0~45.0% respectively, which was similar to that of previous contact lenses. Also, for optical transmittances of each wave length, contact lenses without the UV-absorbent was 89%, 88% and 89% respectively for UV-A, UV-B and visible light, indicating that the UV transmittance is very high though contrary with cases of contact lenses with added 2-hydroxy-4-methoxy-benzophenone and 2,4-dihydroxy-benzophenone which showed transmittances of 0% and 6% respectively for UV-A and UV-B showing a UV-blocking effect. Meanwhile, contact lenses with added $TiO_2$ showed transmittance of 6% and 51% respectively for UV-A and UV-B also showing a UV-blocking effect. The visible transmittance was 77~89% showing that it satisfies the visible transmittance required for ophthalmological materials.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.303-309
• /
• 2006

In this study, functional anion-exchange membranes have been prepared and characterized to improve the permeation fluxes of the anion and urea for peritoneum dialysis. They were prepared by UV and radiation graft polymerization methods. The separation-membrane prepared by UV graft polymerization showed the highest grafting degree when HEMA and VBTAC were mixed by 1:2 ratio. However, the grafting degree decreased slightly at compositions above the 1:2 ratio because of the disruption of UV penetration caused by build-up of homopolymer. In the case of photo-initiator, the grafting degree increased up to 0.2 wt%, above which it decreased to a small extent. For the two membranes prepared by radiation graft polymerization, the VBTAC/HEMA membrane showed 96% grafting degree for 6 h reaction time and the GMA membrane showed over 100% grafting degree for 2 h reaction time. Anion-exchange membranes were prepared with 113% grafting degree and with DEA and TEA exchange groups. The DEA membrane showed the conversion degree of 70% in 4 h reaction time while the TEA membrane showed 30% in 2 h reaction time. The prepared anion-exchange membranes were permeable to only anions and urea, but not cations.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.144-149
• /
• 2010

Ag/polystyrene(PS) nanocomposites were prepared by in situ reduction of silver 2-ethylhexylcarbamate (Ag-CB) complex and follwing radical polymerization only by heating at 110 $^{\circ}C$. In contrast to this conventional heating method, the microwave irradiation afforded well-dispersed silver nanoparticles(NPs) in styrene monomer without polymerization. The synthesis of Ag NPs proceeded uniformly throughout the reaction vessel only under microwave irradiation, completing the reaction simultaneously in the whole reaction solution. Successive polymerization of the monomer containing the resultant NPs has successfully produced a hybrid of the silver NPs dispersed in PS matrix. Ag/PS (0.1/100) nanocomposites were prepared successfully by melt-mixing process using Ag/PS(4.0/100) as a master-batch. UV-VIS spectroscopy, TEM, and X-ray diffraction techniques were used to investigate the process of formation of Ag/PS nanocomposites.