• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.6
• /
• pp.489-496
• /
• 2021

Water disinfection using UV-LED(Light emitting diode) has many advantages, such as smaller footprint and power consumption as well as relatively longer lifespan than those of conventional mercury-UV lamps. Moreover, UV-LED disinfection is considered an environmentally benign process due to its mercury-free nature. In this study, disinfection using an LED module emitting 275nm UV was carried out. 384 UV-LEDs were put into a cylinder tube with a capacity of 1.7 liters. The UV intensity of the UV-LED module was controlled from 1.7 to 8.4 mW/cm². The disinfection efficiency for the model microorganism solutions(E. coli ) was monitored. As the UV intensity(I) and contact time(t) varied, inactivation of the microorganisms from 2 to 4-log-removals(i.e., 99 to 99.99% of disinfection efficiency) was achieved. Disinfection using UV-LED was followed to 1^st order reaction and the reaction rate constant, k was determined. In addition, the relationship between UV intensity(I) and contact time(t) in order to obtain 99.99% of disinfection efficiency was modeled: I^1.2·t= 460, which indicates that the product of UV intensity and contact time requiring 4-log-removals is always constant.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.339-345
• /
• 2018

We investigated the curing properties of cured coatings for a multi-focal UV-LED. The coatings are for LEDs that operate at multiple UV wavelengths, unlike conventional single-wavelength UV-LEDs. Using UV-LED light sources with wavelengths of 365, 395, 420, and 450 nm, we analyzed the optical characteristics such as the direction of light flux and light source. We also analyzed the curing characteristics at each UV-LED wavelength to optimize the LED for composite wavelengths. The curing performance state was predicted through computer simulation for when the multiple wavelengths of UV light sources are superimposed, and then actual LEDs were designed and fabricated. To improve the internal high-speed curing, a multi-spot module was fabricated, in which each LED is condensed, and multiple wavelengths are synthesized and condensed at the same position. The adhesive strength, surface hardness, and internal hardness of the curing agent were tested by varying the wavelength combination conditions. The surface hardening and internal hardening were compared and analyzed using a hardness tester and FT-IR analyzer. As a result, the characteristics of the surface and internal hardness were improved by a multi-spot method in which four wavelengths were overlapped in a UV-LED rather than a single wavelength.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2011.06a
• /
• pp.196-196
• /
• 2011

최근 연구가 활발히 진행되고 있는 UV-LED를 활용한 살균 기술에 있어서 제조 공정상 고가를 유지하는 UV-LED는 그 살균 시스템의 발전에 큰 지장이 되고 있다. 이러한 문제점을 해결하기 위하여 본 연구에서는 LED의 갯수는 줄어들지만 살균 효율은 유지될 수 있는 시스템을 살펴보았다. 이 시스템에서는 UV-LED 갯수를 1개로 유지하며 이를 LED의 방사 Angle에 맞추어 꺾은 상태로 회전하게 되고 그 조광 범위가 향상된다. 또한 그 상태에서 조광구역과의 거리와 회전 시키는 스피드, Angle의 변화에 따른 최적의 위치 및 속도를 찾아보았다. 현재는 일반 가시광 LED를 이용하여 LED를 회전했을 때의 조광 범위와 조광의 정도에 대해서만 서술하였고 추후 UV-LED를 통하여 더 활발한 연구를 진행하려 한다.

• Smart Media Journal
• /
• v.11 no.9
• /
• pp.21-29
• /
• 2022

Ultra Violet(UV) is gradually being replaced with LED instead of general UV lamps. However, the light efficiency of UV LED is still lower than that of the general lamp, and the light efficiency is also low. Due to the current environment and technical problems of UV lamps, the LED replacements are gradually being made. In this study, a new package design and analysis were performed to increase the lifetime and performance of UV LEDs. A new packaging for UV LED were designed and implemented. The new packaging for UV LED was constructed to improve light efficiency. And the electrical and optical characteristics were analyzed respectively. To improve the optical efficiency in UV LED package, the Al has been used based on high reflectivity and applying the optimal lens focusing. Compared to the existing silver Ag, the light efficiency was improved by about 30% or more, and it was confirmed that the light output degradation characteristic was improved by about 10% in the newly applied optical device chip.

• 프린팅코리아
• /
• v.12 no.12
• /
• pp.96-97
• /
• 2013

Air Motion Systems, Inc(대표 Stephen Metcalf)가 개발 공급하고 있는 LED UV램프가 새롬인쇄(대표 장순성)에 국내 1호로 도입됐다. AMS에서 공급하고 있는 LED-UV시스템은 기존의 UV 경화 장치가 전력 소모가 크고 오존이 발생하며 발열이 많아 사용상에 여러 가지 제약이 많았던 것을 획기적으로 개선한 것이 특징이다. AMS의 LED UV램프는 마이크로컨트롤스(대표 조병우)가 아시아 지역을, LH코퍼레이션이 국내를 담당하고 있다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.264-269
• /
• 2019

The design for household sterilizer applying UV LED was studied. Based on UV LED sterilization distance and time data, the concept of home disinfectioner design was presented. Using technologies such as computer aided design software, 3D printing and laser cutting, etc., three different UV LED operating method models were produced. The final design was derived by conducting an analysis of the product's merits and demerits on the three plans from the result of each model.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.133-137
• /
• 2016

Use of UV gel for nail management have been increasing gradually. In order to develop an UV lamp necessary to UV gel, in this study, we was designed circuits of the UV-LED lamp. Power supply part that supplies constant power to the several UV-LEDs, was designed the circuit with the method of DC-DC converter. Taking into account the direction of the thumb nail and the position of the little finger nail, it was placed UV-LEDs. Input power of the power supply part was used as a battery voltage of 3.8[V]. The output voltage of the power supply part was appeared in approximately 3.1[V]. And in order to examine the state of change of the output voltage according to the amount of current consumption of UV-LEDs, after inserting of load resister, the output voltage was more than about 3.0[V] in the simulation results of the power supply part while changing the resistance value.

• Journal of Adhesion and Interface
• /
• v.13 no.1
• /
• pp.31-37
• /
• 2012

In this study, we investigated the curing properties of UV-LED curable color coating. Specially, the effects of UV-LED wavelength (365, 395, and 405 nm), inert gas, the concentration of photosensitizer, and dual curing on the curing behavior of UV-LED coating systems were studied. The photopolymerization behaviors and the unreacted acrylate groups at Film-air (FA) interface and Film-substrate (FS) interface were investigated by photo differential scanning calorimetry (Photo-DSC) and Fourier-transform infrared spectroscopy with attenuated total reflection (FT-IR/ATR), respectively. Photo-DSC results showed that the heat flow and the ultimate conversion for coating system cured by 405 nm UV-LED were higher than the corresponding values for coating systems cured by 395 and 365 nm UV-LED. FT-IR/ATR results showed that the UV-LED curing systems improved interior and through curing of the coating film, but significantly are affected by oxygen inhibition at FA-interface. The inert environment such as nitrogen purging and the dual curing improved the surface and interior curing of the coating films.

• Korean Journal of Optics and Photonics
• /
• v.35 no.5
• /
• pp.235-240
• /
• 2024

Since the coronavirus pandemic, research and application of space sterilization effects using UV light sources have been rapidly increasing. In this paper, the space-sterilization effect of UV LED light sources that can be built into indoor environmental systems or lighting devices is quantitatively analyzed through an illumination optical approach. Through this, it is possible to establish a foundation for optimizing the sterilization effect in indoor spaces in the 275±5 nm wavelength range, which is known to have excellent space-sterilization power.

• Horticultural Science & Technology
• /
• v.34 no.4
• /
• pp.596-606
• /
• 2016

The growth and contents of anthocyanins and ascorbic acid in lettuce(Lactuca sativa L., 'Jeokchima') as affected by supplemental UV-A LED irradiation under different light quality and photoperiod conditions were analyzed in this study. Five light qualities, namely B (blue LED), R (red LED), BUV (blue LED+UV-A LED), RUV (red LED+UV-A LED) and Control (white fluorescent lamps) with photoperiods of 12/12 hours (day/night), 16/8 hours, or 20/4 hours were provided to investigate the effects of light quality and photoperiod on the growth and accumulation of anthocyanins and ascorbic acid in lettuce leaves. As measured 28 days after transplanting, the number of leaves, leaf length, leaf width, leaf area, shoot fresh weight and dry weight of lettuce were significantly affected by light quality and photoperiod. The number of leaves, leaf length, leaf width, leaf area, shoot fresh weight and dry weight of lettuce grown under R treatment increased with increasing light period. By contrast, leaf development was inhibited, but chlorophyll content increased, under B treatment. Supplemental UV-A irradiation significantly decreased leaf length, leaf width, leaf area and shoot fresh weight. Anthocyanins in lettuce increased significantly with decreasing dark period under B treatment. A synergistic effect of supplemental UV-A LED irradiation on anthocyanins accumulation was found for lettuce leaves grown under R treatment but not B treatment. Ascorbic acid in lettuce was greatly affected by photoperiod. Ascorbic acid content at BUV and RUV treatments increased by 20-30% compared to without UV-A LED irradiation. From these results, it was concluded that growth and contents of anthocyanins and ascorbic acid in lettuce are significantly affected by supplemental UV-A LED irradiation. The results obtained in this study will be informative for efforts to improve the nutritional value of leafy vegetables grown in plant factories.