• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.116-119
• /
• 2003

Self-patterning of thin films using photosensitive sol solution has advantages such as simple manufacturing process compared to photoresist/dry etching process. In this study, ferroelectric $Sr_{0.9}Bi_{2.1}Ta_2O_9$(SBT) and $La_{0.5}Sr_{0.5}CoO_3$(LSCO)thin films have been prepared by spin coating method using photosensitive sol solution. $Sr(OC_2H5)_2$, $Bi(TMHD)_3$ and $Ta(OC_2H)_5)_5$ were used as starting materials for SBT solution and $La(OCH_2CH_2OCH_3)_3$, $Sr(OC_2H_5)_2$, $CO(OCH_2CH_2OCH_3)_2$ were used for LSCO solution. Solubility difference by UV irradiation on LSCO thin film allows to obtain a fine patterning due to M-O-M bond formation. The lowest resistivity($4{\times}10^{-3}{\Omega}cm$) of LSCO thin films was obtained by annealing at $740^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.9
• /
• pp.867-874
• /
• 2000

Two new azobenzene crown ether calix[4]arenes, 10 and 11, were synthesized by two pathways. In the first pathway,two ethoxy nitrobenzene groups were attached to t-butylcalix[4]arenes in a 1,3 position. Subsequent reduction ofthe nitrobenzene group s by metallic zinc in an alkaline solution afforded 10 and 11 in8% and 12%,respectively. In the second pathway,an azobenzene containing two glycolic units was prepared prior connect-ing to t-butylcalix[4]arenes. The yields from the second approach (5%, 8% for 10 and 11, respectively) were lower than those from the former approach. Single crystals of 10 suitable for X-ray crystallography was ob-tained by recrystallization in methanol.Both the X-ray structure and the 1H-NMR spectrum of 10 indicated that the stereoisomer of the azobenzene moiety was trans and the calixarene platform was in cone conformation. 1H NMR spectroscopy suggested that 10 underwent an observable cis-trans isomerization in CDCl3 under room light and upon UV irradiation with cis:trans ratios of 33:67 and 36:64,respectively. Compound 6 which was the precursor of 11showed fluxional behavior and was found to have mixed conformations ofcone and partial cone with a ratio of 47:53 at -30 $^{\circ}C.$ 1H NMR spectrum of 11 suggested that 11 was initially isolated as cis azobenzene with calix[4]arene in cone conformation and underwent conformational interconversion through calix[4]arene annulas in a similar fashion to 6 upon exposing to light. The complexation studies of 10 with picrate salts of Na+ and K+ using 1H NMR spectroscopysuggested that Na+ preferred to bind the cis form of 10 while K+ preferred to bind the trans form. The stereoisomer of the azobenzene unit in 11 changed partially from cis to trans upon complexing with K+.

• Journal of Appropriate Technology
• /
• v.6 no.2
• /
• pp.226-237
• /
• 2020

As the number of reported COVID-19 cases rises around the world, regions affected by the virus are taking serious measures to contain its spread. Face shields are one of the highest-need personal protective equipment (PPE) during COVID-19 pandemic. Beyond traditional face masks, as known cases of the coronavirus soar, currently there is a significant shortage of face shields around the world. In response, the protective face shields were designed and fabricated with open-source 3D modelling software and 3D printing technology, respectively. Our face shield consisted of two parts only; a reusable 3D printed headband and a visor made of transparent plastic sheet, as barrier. The resulting 3D printed face shields are affordable, lightweight, one-size-fits-most and ready-to-wear with minimal assemblies, and go on easily over glass, goggle and face mask. To ensure being donated to the healthcare professionals without risk infected by any pathogens, the 3D printed face shields were successfully be disinfected with ultraviolet germicidal irradiation (UVGI dosage of 1000 mJ/cm²) and 70% alcohol. For routine disinfection a UVGI chamber was designed and optimized to provide uniform UV-C illumination with an appreciated fluence for complete decontamination. More than 1,000 face shields were produced already and donated to the special hospitals for COVID-19 patients, quarantines, government and medical agencies in Ethiopia as well as in East-African countries. With certainty, our intention goes beyond the hospitals and other first responders, but not limited for all those who have to stay in the service or be in contact with many other people in the time of COVID-19 pandemic.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.1
• /
• pp.107-112
• /
• 2011

In this study, photocatalytic degradation and mineralization of bisphenol A (BPA), which has been listed as one of endocrine disruptors, were carried out in the CPC system using $Tio_2$ slurry and UVA irradiation. The degradation efficiency has been investigated under the controlled parameters including initial concentration (5, 10, 20 mg/L), dosage of $Tio_2$ (0.1, 0.5, 1.0 g/L), UVA power (0, 80, 120 W) and temperature (0, 20, 30). At 10mg/L of initial concentration, BPA was degraded above 80% after 10min, BPA were degraded 97% and 49% at 20 mg/L and 30 mg/L, respectively. At $Tio_2$ dosage was 0.1 and 0.5 g/L, the degradations of BPA showed similar trend and were about 70% after 1 hr, and the degradation of BPA was above 80% after 30 min at 1 g/L of $Tio_2$ dosage. The increase of degradation seem to be due to the increase in the total surface area, namely number of active sites, available for the photocatalytic reaction as the dosage of photocatalyst increased. When the UVA power was 120 W, BPA was degraded rapidly above 60% after 10min of reaction time. To investigate the effect of temperature, carried out experiment controlled temperature, there were no significant differences depending on the temperature. After 1hr, the degradation of BPA were 46%, 67%, and 69% at 10, 20 and $30^{\circ}C$.

• Applied Biological Chemistry
• /
• v.20 no.1
• /
• pp.66-80
• /
• 1977

This research was carried as a part of the basic study, in which the aptitude of theKorean oak varieties as barrels for aging apple fine spirits was investigated, and thefollowing results were obtained. 1. Following was the result of the chemical analysis of the fruits which are now mass-produced and can be used as a substitute for raw materials for wine production. Apple (Malus pumila Miller var. domestica Schneider) : Total sugar. total acid, volatile acid and pectin of Jonathan (Hong-og) were 13.95%, 0.46%, 0.012%, 0.20% respectively. Total sugar, total acid, volatile acid and pectin of Ralls (Koog-kwang) were 13.35%, 0.43%, 0.011%, 0.45% respectively. 2. Because of low yield of apple juice due to cellulose, pectin, hemicellulose which are present besides sugars, acids in apples, the apple juice were treated with xylanase of Aspergillus niger SUAFM-430, cellulase and pectinase of Aspergillus niger SUAFM-6. This treatment increased the yield of apple juice. And the apple juice was sterilized by adding potassium metabisulfite $(K_2S_20_5)$ and Saccharomyces cerevisae var. ellipsoideus Rasse Johannisberg II (SUAFM-1018) as a cultivation yeast, which has a strong fermentation power was used to ferment. The yield of apple wine based on raw material was 86-87%. The amount of ethanol, extract and methanol obtained from Jonathan and Ralls were 13.5%, 5.4%, 0.04-0.05% respectively. 3. Wines were distilled for two times by the pot still method to make fine spirits. The yield of fine spirits from apple wine mash was 86.6%, and the pH of fine spirits from Jonathan and Ralls were 4.1, 4.2 respectively. 4. The oak chips made of inner part or outer part of 24 Korean oak varieties were used to select the barrel for aging fine spirits. Two oak chips (one oak chip: $1{\times}1{\times}5cm$) of the inner part or of the outer part of each oak variety were dipped into 300 ml of fine spirits, which was bottled in 640ml beer bottle, and followed aging. The colors, flavors and tastes of the fine spirits were checked during 6 months. A. As a criterion for the first screening of oak barrels for aging fine spirits, the rate five of color extraction was determined. The oak chips showed good results in their order as follows and the best 5 varieties were selected. Gal-cham: Quercus aliena Blume (Inner part), Gul-cham: Quercus variabilis Blume (Outer part), Gal-chain: Quercus aliena Blume (Outer part), Jol-cham: Quercus serrata Thumb (Inner and Outer part). Sin-gal-cham: Quercus mongolica Fisher (Outer and Inner part) Sang-su-ri: Quercus acutissima Carruthers (Outer and Inner part) B. To find out the influence of aging temperature on aging, apple fine spirits were aged by dipping each oak chip at room temperature $(24-25^{\circ}C)$) and $45^{\circ}C$. Aging at $45^{\circ}C$ gave the best result followed aging at $30^{\circ}C$ and then at room temperature. C. Apple fine spirits was aged for six months by dipping oak chips in Erlenmeyer flasks and was irradiated with U.V light. The U.V irradiation enhanced the aging effect by nearly two times, compared with the aging without U.V irradiation. D. In aging apple fine spirits by dipping two oak chips, it was observed that the extent of the extraction of most components of oak chips were strongly dependent upon the pH of fine spirits. E. Oak chips of five selected oak varieties and a Limousin white oak from France as a control were used. Each apple fine spitits was dipped by two oak chips, and was aged at room temperature $(24-25^{\circ}C)$, $30^{\circ}C$, $45^{\circ}C$, and with the U.V irradiation at room temperature shaking every week. After six months of aging, the panel test of these aged fine spirits (Young Brandy) showed the following result. Young brandy of apples aged at $45^{\circ}C$ by dipping oak chips of Gal-chain was almost as the fine spirits which were aged at room temperature by dipping Limousin white oak chips from France. Young brandy of with U.V. irradiation at room temperature which were aged by dipping oak chips of Gal-chain was a little worse than that from the fine spirits aged at room temperature by dipping Limousin white oak chips from France. And so, Korean oak varieties are thought to be able to be used for aging every apple fine spirit which was here investigated.

• Journal of Animal Science and Technology
• /
• v.47 no.4
• /
• pp.547-554
• /
• 2005

An experiment was conducted to investigate the dietary effects of a transgenic Aspergillus oryzae(AO) culture on the performance, egg quality and intestinal microflora of layers. A total of 840 Hy-line Brown layers of 39wks old were assigned to one of the following 7 dietary treatments: control(C), C+0.2% AO culture, C+0.5% AO culture, C+0.2% transgenic AO culture, C+0.5% transgenic AO culture, C+0.2% transgenic mutant AO culture, and C+0.5% transgenic mutant AO culture. The transgenic AO was made by inserting Salmonella gallinarum gene to AO. And the transgenic mutant AO was made by inserting Salmonella gallinarum gene to mutant AO which was mutated by UV irradiation. Each treatment was replicated six times with 20 birds housed in 2 bird cage. Twenty birds units were arranged according to completely randomized block design. Feeding trial lasted for 8wks under 16 hour lighting regimen. Laying performance and egg quality were significantly(P<0.05) affected by the treatments. Transgenic AO culture supplementation at the level of 0.2% significantly increased egg production, while its egg weight was significantly decreased compared to that of the control. Feed intake and feed conversion ratio(FCR) were not significantly different among the AO treatments and the control. The eggshell strength of the AO treatments was significantly higher than that of the control. Transgenic mutant AO culture supplemented at the level of 0.5% significantly increased egg yolk color. Intestinal microflora were significantly(P<0.05) affected by the treatments. The cfu of Lactobacilli spp. significantly increased and those of Salmonella species and E. coli decreased in the AO treatments. The transgenic AO and transgenic mutant AO culture were more effective than the AO culture in reducing the cfu of Salmonella species and E. coli. It is concluded that supplementation of the transgenic AO culture at the level of 0.2% could be recommended for the improvement of egg production. Supplementation of transgenic AO or transgenic mutant AO culture at 0.2% level effectively controlled intestinal Salmonella species population.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.2
• /
• pp.181-187
• /
• 2004

Preparations of mesoporous materials using various templates and their applicability have been intensively investigated for many years. We studied on synthesizing mesoporous Ti02 with pores in which sensitive compounds having weak physico-chemical properties such as thermal or UV irradiation and low solubility in solvent are trapped. Prior to trapping OMC in the pores of mesoporous titania, OMC was nano-emulsified in O/W system using Lecithin. Thereafter the OMC was trapped in the pores of mesoporous titania using sol-gel method. Main focus of this work is to prepare OMC-trapped mesoporous titania and to trace the stability and solubility of nano-emulsified OMC in the pores of mesoporous titania, and compared with that of mesoporous silica. OMC-trapped mesoporous Inorganic-Organic hybrid titania showed higher factors in sun protecting and a skin penetration phenomenon was reduced.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.5
• /
• pp.241-245
• /
• 2013

Granular bamboo-derived active carbons (AC) were impregnated (or coated) with $TiO_2$ nano crystalline powders. The photocatalytic activity of the $TiO_2$-impregnated active carbons ($TiO_2$/AC) were determined on the basis of the degradation rate of methylene-blue aqueous solution under UV irradiation. The active compounds of $TiO_2$ were impregnated onto the AC under moderate hydrothermal conditions (${\leq}200^{\circ}C$, pH 11). The mean size of $TiO_2$ particles calculated from BET surface area were found to be as 50 nm. The $TiO_2$ precipitates were coated on the cavities or pores on the surfaces of highly activated carbons. Since the hydrothermal process led to a lowering of the on-set temperature of the anatase-to-rutile transition of $TiO_2$ as low as $200^{\circ}C$, $TiO_2$ crystallites of a pure anatase or a mixed form with rutile were successfully coated on the AC depending on the synthesis temperatures.

• Applied Biological Chemistry
• /
• v.18 no.1
• /
• pp.23-29
• /
• 1975

This experiment was conducted to study the effects of temperature and pH upon the acid productivity of the acid producing mutant induced by the treatment of ultraviolet light, and to identify the producing acid by PPC and p-oxydiphenyl method. Chemical composition of Takju mash brewed with selected yeast and producing acid were observed and the results were as follows. 1) There was no apprecible difference in acid producing activity of mutant at $25^{\circ}C\;to\;30^{\circ}C$. 2) The acid producing activity of mutant was little below pH 4 and was gradually increased according to approach nenutral, and the accumulation of acid was amounted to 0.5-0.7% as a lactic acid at pH 5 to 7 within 48 hrs of fermentation. 3) The acid produced by mutant was detected to the lactic acid. 4) In the cases of the Takju was brewed with the starter from the acid producing mutant the requirement of Ipkuk was 5% for all the raw materials, on the contrary, using orginal strain the requirement of Ipkuk was 20%. 5) In the case of both starters from the acid producing mutant and orginal strain were added at different brewing times, and only Bunkuk was used as a saccharifying agent (without Ipkuk), Takju was able to brewed more repidly and successfully than the case of general process.

• Analytical Science and Technology
• /
• v.20 no.4
• /
• pp.279-288
• /
• 2007

We have studied a method for the preparation of $ACF/TiO_2$ composites involving the penetrationof titanium n-butoxide (TNB) solution into activated carbon fiber. It was focused on the characterization of $TiO_2$ formed in prorous carbon was which increased with surface functional groups by hydrochloric acid treatment. The conversion of TNB to $TiO_2$ for the acid treatment effect must be important for the preparationof $ACF/TiO_2$ composites. From the characterization of surface properties, both the BET surface area and the total pore volume decreased as the distribution of $TiO_2$ on the activated carbon fiber surfaces after acid treatments.The changes in XRD pattern showed the typical anatase type on $ACF/TiO_2$ composite for the sample named FT, FT1 and FT2 treated with 0.05, 0.1 and 0.5 M, respectively. However, XRD patern of FT3 treated with 0.5M showed mixed amatase-rutile structure. According to the results of SEM micrographs, the titanium complexe particles were irregularly distributed around carbon. And some large clusters were found when an amount of acid treatment increased. The EDX results of $ACF/TiO_2$ composites showed the presence of C, O and P with strong Ti peaks. Finally, the excellent photocatalytic activity of the $ACF/TiO_2$ composites between relative concentration($c/c_o$) of MB (methylene blue) and UV irradiation time could be attributed to the both effects between photocatalysis of the formation of titania complexes and adsorptivity of the activated carbon fiber.