• The Research Journal of the Costume Culture
• /
• v.11 no.6
• /
• pp.967-971
• /
• 2003

As the concerns over health increased in 1990's, research and development on the health material were also activated. The development of UV-cut textile became the hot issue, because the damage of W irradiation due to ozone depletion has become widely known. UV-cut effect is determined by the material, the color, the organization and the density of UV-cut fibers. UV-cut effect is very different according to the fibers. Polyester is known to have a better effect. Even in the same textile material, staple fiber has more effect than filament fiber. Different colors have different offsets. Although textiles have the same color, the effects can be different according to the depth of color. PET, PET/cotton blend, nylon and cotton fabrics were ultraviolet cutting finished with padding method using several absorbers. These UV-cut effect can be improved through the processing. Safety of UV-cut textile for the body must be considered future, Until now the figure of the UV-cut effects has been emphasized. There has been no experiment on the human body, although the textiles are directly on the human body. Futhermore there os no safety standard of UV-cut textiles. Therefore every effort will be made to set the standard UV-cut processing is established. The need of UV-cut products will be known to the consumers.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.107-110
• /
• 2001

In order to estimate the UV-A line's cut efficiency it lens, it was measured the light transmittance in the 320~400nm wavelength regions. We obtained the area to integrate the light transmittance of standard CR-39 and sample in the 320~400nm wavelength regions and established ${\alpha}$, ${\beta}$ of UV-A line's cut efficiency by contrast its area. We obtained the absolute cut efficiency ${\alpha}$ CR=0.59 value of CR-39 Lens, and if ${\alpha}$ was the absolute cut efficiency value of the lens to estimate UV-A cut effect, the relative cut efficiency ${\beta}$ was $1.69{\alpha}$. It was obtained the absolute and the relative UV exclusion index through each $a=(1-{\alpha}){\times}100%$, $b=(1-{\beta}){\times}100%$.

• Journal of the Korean Home Economics Association
• /
• v.46 no.10
• /
• pp.1-9
• /
• 2008

The purpose of this study was to increase uv-cut ability of cotton, ramie, and rayon fabrics dyed with safflower red colorants. For this purpose, samples treated with uv-cut agent and tannic acid were compared with the untreated samples after ultraviolet(uv)-light exposure in terms of K/S value, color changes(${\Delta}E$), SEM, and tensile strength retention. K/S value rapidly decreased with increasing exposure time, but K/S value of the samples treated with both uv-cut agent and tannic acid decreased less than that of untreated samples. As increasing exposure time, $L^*$ and $b^*$ increased, $a^*$ decreased, and so ${\Delta}E$ increased, indicating less red character and more yellow character in color. This leads to change hue, value and chroma value. But color change of samples treated with both uv-cut agent and tannic acid was less than that of untreated samples. SEM pictures showed a severe degradation by uv exposure in all samples. Tensile strength slowly decreased for 21 days. And after this point, the decreased proceeded more rapidly. Tensile strength retention of the samples treated with uv-cut agent and tannic acid was higher than that of untreated samples.

• Journal of the Korean Home Economics Association
• /
• v.45 no.10
• /
• pp.73-81
• /
• 2007

The purpose of this study was to increase the ultraviolet-light (UV)-cut ability of cellulose fabrics (cotton, ramie, and rayon) dyed with safflower yellow colorants. For this purpose, samples treated with UV-cut agent and tannic-acid were compared with the untreated samples after UV exposure in terms of K/S value, color changes(${\Delta}E$), SEM, and strength retention. The K/S value rapidly decreased after 28 days exposure, whereas the K/S value of the samples treated with both UV-cut agent and tannic-acid decreased to less than that of the untreated samples. In color changes, $L^*$ increased while $a^*$ and $b^*$ decreased, indicating less red and yellow character in color. This induced a change in the hue, value and chroma values. However the color change(${\Delta}E$) of the samples treated with both UV-cut agent and tannic-acid was less than that of the untreated samples. Scanning electron microscopy (SEM) pictures showed a severe degradation by exposure in all samples. Tensile strength rapidly decreased after 28 days for cotton and rayon, and after 21 days for ramie. However, the strength retention of the samples treated with UV-cut agent and tannic-acid was higher than that of the untreated samples.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.129-134
• /
• 2002

We obtained the UV cut-off effect of tinted CR-39 Ophthalmic lens with the respect of concentration of green, brown, blue color. First, we analyzed the UV spectrum of tinted CR-39 lens measured by Spectrophotometer and then compared the UV data by Spectrophotometer with UV data by UV tester used in an optician shop. The result obtained show that the UV cut-off effect is increased with color concentration of tinted CR-39 lens, and the transmittance of 0%~5% at 400nm by Spectrophotometer is correspondence with transmittance of 0% by UV tester.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.5
• /
• pp.925-932
• /
• 2001

The influence of ultraviolet(UV)-ray in sun light on human skin has been noted. Textiles can provide protection against harmful UV-radiation. Normally UV-absorbing finishes are used to get better protection. The purpose of this study is to evaluate the UV-cut properties of cotton fabrics treated with UV-absorber. 2,2-dihydroxy-4,4-dimethoxbenzophenone, as UV-absorber was applied to 100% cotton fabric. Reagents added in finishing solution were Triton X-100, polyethylene glycol 400, and $MgCl_2{\cdot}6H_2O$, and C.I. Direct Red 81. Both untreated and treated cotton fabrics were exposed to a xenon arc lamp for 20 and 80 hours. UV absorption spectra of finishing solutions and UV transmission spectra of fabrics were measured by the UV/VIS spectrophotometer. The results of this study can be summarized as follows. The results of this study can be summarized as follows. Absorption and the related transmission spectra were modified in a controlled way with UV-absorber. Absorption effect of UV-absorber was improved by adding Triton X-100, PEG 400, and $MgCl_2{\cdot}6H_2O$ in finishing solution. The UV absorption of finishing solution was in the following order: U/D/T/P/M>D/T/P/M> D/T> D/P, D>U/T/P/M>U/T>T/P/M>T. The UV transmittance of cotton fabrics was remarkably decreased by the application of UV-absorber and additives. The UV-cut properties were most improved by the application of U/D/T/P/M.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.5
• /
• pp.622-627
• /
• 1994

The purpose of this study is to investigate the adsorption rate, adsorption quantities and the UV-Cut effects of cotton fabrics treated with several UV absorbents. The result of this study were as follows: cotton fabric treated with 2,2'-dihydroxy-4- methoxy-benzophenone shows more efficient than ones treated with 4-aminobenzoic acid and 2·hydroxy-1, 4-naphthoquinone in UV absorption. This may be due to the absorption of UV light by formation of intra moleculaar hydrogen bond. The formation of hydrogen bonds between hydrogen atoms of two hydroxy groups and one oxygen atom of carboxyl group in 2, 2'-dihydroxy-4-methoxy-benzophenone would be easier than that of the other absorbents. The adsorption isotherms of 4-aminobenzoic acid and 2-hydroxy-1, 4-naphthoquinone were similar to Freundlich type, while that of 2, 2'-Dihydroxy-4-methoxy-benzophenone was Henry type. Cotton fabrics treated with Antifade MC-100 and W Cut I-2 were just alike in UV absorption, but Antifade 8001 was inferior to the others.

• Textile Coloration and Finishing
• /
• v.14 no.4
• /
• pp.223-228
• /
• 2002

Cotton fabric was treated with $TiO_2$-PEG600 dispersion colloid by pad-dry-cure and wet-fixation process to improve the performance properties as well as UV-cut effect. As the concentration of $TiO_2$/PEG increased tensile strength, crease resistance, stiffness of treated cotton fabric increased. Application of wet-fixation method provided a further improvement in tensile strength, crease resistance, stiffness of treated cotton fabric. Cotton fabric treated with $TiO_2$/PEG was more efficient in UV-cut property than untreated cotton.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.17-21
• /
• 2001

We analyzed the luminance in the visual light region and the size of pupil by the luminance to estimate an UV-A line cut efficiency in the lens. The size of pupil by the luminance(L) was given by ${\Phi}=d-e{\cdot}tanh(f{\cdot}logL)$ and the transmittance efficiency value of a size of pupil was given by $T_r(r)=1-gr^2+hr^4$. We derived the absolute cut efficiency value ${\alpha}$ and the exclusion index $b=(1-{\alpha}){\times}100%$ about the UV-A in the $320{\sim}400nm$ regions. The ${\alpha}$ and b values were obtained respectively 0.018, 0.31, 0.273, 0.153 and 98, 69, 72, 85% of Uv-cut Lens, CR-39, red color and blue color.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.3
• /
• pp.9-17
• /
• 2010

The FPCB is used for electronic products such as LCD display. The process of manufacturing FPCB includes a cutting process, in which each single FPCB is cut and separated from the panel where a series of FPCBs are arrayed. The most-widely used cutting method is the mechanical punching, which has the problem of creating burrs and cracks. In this paper, the cutting characteristics of the FPCB have been experimented using Nd:YAG DPSS UV laser as a way of solving this problem. To maximize the industrial application of this laser cutting process, test samples of the multilayered FPCB have been chosen as it is actually needed in industry. The cutting area of the FPCB has four different types of layer structure. First, to cut the test sample, the threshold laser cut-off fluence has been found. Various combinations of laser and process parameters have been made to supply the acquired laser cut-off fluence. The cutting characteristics in terms of the variation of the parameters are analyzed. The laser and process parameters are optimized, in order to maximize the cutting speed and to reach the best quality of the cutting area. The laser system for the process automation has been also developed.