• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.308-315
• /
• 2006

Since sewage characteristics are the most important factors that can affect the biological reactions in wastewater treatment plants, a detailed understanding on the characteristics and on-line measurement techniques of the influent sewage would play an important role in determining the appropriate control strategies. In this study, samples were taken at two hour intervals during 51 days from $1^{st}$ October to $21^{st}$ November 2005 from the influent gate of sewage treatment plant. Then the characteristics of sewage were investigated. It was found that the daily values of flow rate and concentrations of sewage components showed a defined profile. The highest and lowest peak values were observed during $11:00{\sim}13:00$ hours and $05:00{\sim}07:00$ hours, respectively. Also, it was shown that the concentrations of sewage components were strongly correlated with the absorbance measured at 300 nm of UV. Therefore, the objective of the paper is to develop on-line estimation technique of the concentration of each component in the sewage using accumulated profiles of sewage, absorbance, and flow rate which can be measured in real time. As a first step, regression analysis was performed using the absorbance and component concentration data. Then a neural network trained with the input of influent flow rate, absorbance, and inflow duration was used. Both methods showed remarkable accuracy in predicting the resulting concentrations of the individual components of the sewage. In case of using the neural network, the predicted value md of the measurement were 19.3 and 14.4 for TSS, 26.7 and 25.1 for TCOD, 5.4 and 4.1 for TN, and for TP, 0.45 to 0.39, respectively.

• Journal of Radiation Protection and Research
• /
• v.32 no.2
• /
• pp.65-69
• /
• 2007

The effects of bamboo (Phyllostachys nigra var. henenis Strapf) leaf extract (BLE) on the changes of ultraviolet (UV) light B radiation-induced apoptotic sunburn cell (SBC) and epidermal ATPase-positive dendritic cell (DC) in SKH1-hr or ICR mouse were investigated. The mice were treated with UVB ($200mJ/cm^2$) and were sacrificed 24 hours later. BLE (50 mg/kg of body weight) or vehicle (saline) was given i.p. at 36 and 12 hours before irradiation, and 30 minutes after irradiation. BLE cream (0.2%) or cream base (vehicle) was also topically treated at 24 hours and 15 minutes before irradiation, and immediately after irradiation. The skin of SKH1-hr mouse prepared from the back of untreated mice exhibited about 0.3 SBC/cm length of epidermis, and 24 hours after UV irradiation, the applied areas show an increased number of SBCs. But the frequency of UVB-induced SBC formation was significantly reduced by intraperitoneal injection (59.0%) and topical application (31.8%) of BLE extract. The numbers of DC in normal ICR mouse were $628.00{\pm}51.56\;or\;663.20{\pm}62.58\;per\;mm^2$ of ear epidermis. By 1 day after UVB treatment, the number of ATPase-positive $cells/mm^2$ were decreased by 39.0% or 27.1% in i.p. or topical application group with vehicle. The frequency of UVB ($200mJ/cm^2$)-induced DC decrease was reduced by treatment of BLE as 25.7% in i.p. group and 3.2% in topical application group compared with the irradiation control group. The results presented herein that BLE administration could reduce the extent of skin damages produced by UVB.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.37-46
• /
• 2015

In the case of adhesives & restoration agents currently being used for the preservation treatment of ceramics and earthenware, epoxy type, cellulose type and cellulose type are mainly being used. However, they are showing various problems such as re-detachment from severe contraction, color change from yellowing, work inconvenience of staining on tools and hand during usage and irreversibility. For the purpose of solving the issues of yellowing and irreversibility of epoxy resin being used to restore ceramics, urethane synthetic resin with low yellowing excellent reversibility has been developed in this study. The adhesive strength of urethane resin that has been developed has excellent properties with 2.07MPa for undiluted solution, which is 1.5 times higher than that of existing material EPO-$TEK301^{(R)}$ 1.21MPa. The result of workability measurement showed that the wear rate of urethane resin (in Talc 50wt%) was 1.09%, which was somewhat higher than that of existing material Quick $Wood^{(R)}$ (1.02%). In addition, its wear rate is two times higher than that of $EPO-TEK301^{(R)}$ (0.41%) and $L30^{(R)}$ (0.39%), thereby showing an advantage in its forming process compared to existing materials. As for the advantage of urethane resin of reversibility experiment, 12 hours after acetone, ethyl alcohol deposition, urethane resin and filler talc were dissolved 100% while showing powdering phenomenon. Compared to 0% reversibility of existing epoxy resin, it has much superior reversibility. The result of UV rays experiment to evaluate its durability showed that ${\Delta}E^*ab$ color change value based on undiluted solution of urethane resin was 2.76 before & after UV rays exposure, which was a decrease by about 7-20 times compared to that of existing resin, thereby minimizing the issue of heterogeneity.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.3
• /
• pp.281-287
• /
• 2011

BACKGROUND: According to Korean regulations, bottled waters (BWs) can not be treated with chemical disinfectants like chlorine, so UV and ozone disinfection is applied. During the past several years, chemicals were detected in some BWs, and the public was concerned about the safety of BWs. METHODS AND RESULTS: Mineral waters were stored for 180 days at $25^{\circ}C$ and $50^{\circ}C$, tested acetaldehyde and formaldehyde by HPLC. When mineral waters were put in a PET bottles, the formaldehyde level ranged from 5 to $66{\mu}g/L$ during 180 days at $50^{\circ}C$. While the acetaldehyde level ranged from 31 to $221{\mu}g/L$, it was low than $16{\mu}g/L$ in glass bottle. CONCLUSION(s): This result showed that formaldehyde and acetaldehyde were detected higher in PET bottles than glass bottles, these also increased depending on the time of storage. Concentration of formaldehyde and acetaldehyde could be significantly influenced by the time of storage and temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.163-177
• /
• 2019

This study aims to review the relations between the dyeing conditions (i.e., dye concentration, addition amounts of salt and alkali, and dyeing temperature) and dyeing properties and color fastness to light for identifying the optimal dyeing conditions when dyed regenerated woody fibers were obtained through the defibration of waste medium density fiberboard (MDF) using reactive Red H-E3B (Bis-monochlorotriazine (MCT)/MCT type) and reactive Red RB133% (Bis-MCT/Vinyl sulphone type). The dyeing yield (K/S) obtained using two types of reactive dyes increased as the dye concentration increased by 1-10% (on the weight of fiber (OWF)). In addition, the K/S of H-E3B was higher than that of RB133% irrespective of the dye concentration. The color difference of H-E3B after ultraviolet (UV) radiation was lower than that of RB133%, denoting good resistance to discoloration by UV. As the amount of sodium sulfate increased, the color difference and K/S also increased, and the adequate salt content was determined to be 50-70 g/L. Further, the color difference and K/S significantly increased only the addition of 2 g/L of sodium carbonate; however, almost no difference was observed when more than 2 g/L of sodium carbonate was added. The addition amount of sodium carbonate was adequate 5-10 g/L to dyeing the fiber and the pH at this addition level was 10. The dyeing yield of H-E3B increased when the dyeing temperature increased; however, it subsequently decreased after the dyeing temperature became $80^{\circ}C$. The dyeing yield of RB133% was almost the same up to $60-70^{\circ}C$ but declined subsequently. Thus, the adequate temperatures were $80^{\circ}C$ and $60^{\circ}C$ for H-E3B and RB133%, respectively. If the waste MDF woody fiber was dyed under the aforementioned optimal conditions, dyed regenerated woody fiber can be obtained having the following colors: 1.5 to 2.0R with the H-E3B dye and 9.6 to 10.0 PR with RB133%.

• Applied Biological Chemistry
• /
• v.18 no.1
• /
• pp.16-22
• /
• 1975

This experiment was carried out to investigate the physiological characteristics of two original yeasts, 5-Y-5 and 6-Y-6, which selected from 24 Takju yeasts and three mutants, 30-24,30-81 and 40-27. induced from two original yeasts by the irradiation of UV light. The results were summarized as follows. 1) Alcohol tolerances of three mutants were decreased in some degree as compared with those of original yeasts. 2) Tolerances of lactic and citric acids of acid producing mutant 30-81, was increased than those of original yeasts. 3) In the case of using ammonium sulfate as a nitrogen source, two original yeasts and three mutants required Ca-pantothenate as a essential growth factor and four strains of yeasts except the mutant, 30-81, required biotin as a stimulated growth factor, When asparagine was used as a nitrogen source, two original yeasts and three mutants showed the same as above result but the stimulated effect of biotin was far less. 4) Propagation powers of the mutants were weaken than those of original yeasts, particular that of acid producing mutant, 30-81, was the weakest in the three mutants. 5) The optimum temperature for fermentation of original yeasts were $30^{\circ}C\;to\;35^{\circ}C$ but three mutants were $25^{\circ}C\;to\;30^{\circ}C$. 6) The optimum pH for fermentation of original yeasts were pH 5 to 6, and there is no appreciable difference between original yeasts and three mutants. The fermentation power of mutant,30-81, was decreased more rapidly than those of other mutants according to approach neutral. Three mutants were more sensible to heat than original yeasts. 7) Two original yeasts and three mutants were inhibited more over 20 percent of sugar for fermentation and three mutants were more sensible to sugar concentration than original yeasts.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.3
• /
• pp.197-207
• /
• 2018

The radish skin and radish greens (mucheong) are an edible part of the radish. But they are removed before eating the radish and used as a byproduct or an animal feed material because of their tough and rough texture. This study was conducted to investigate the effect of supercritical heat-treated radish-extract on UV-induced Hos: HRM-2 wrinkled mouse animal model on anti-aging wrinkles. Supercritical heat-treated radish-extract was applied on the back of seven-weeks old HRM-2 mice. The effect of HRE on skin thickness, elasticity and wrinkle formation of the mice was observed by using UVB lamp to induce melanogenesis and wrinkle formation. As the result, increased depth of wrinkles was observed in the negative control group in comparison to the normal group. In contrast, decreased depth of wrinkles was observed in the radish-extract-free group compared to the negative control group. In the study of the effect of radish-extract on wrinkle-formation related gene expression and protein what protein expression, MMP-2 and MMP-2 gene expression significantly increased in the negative control group compared to the normal group. The gene expression reduced independence to the mass of radish-extract treated. Similar to quantitative results of mRNA expression, the expression of MMP-2 protein increased as a result of UVB-irradiation. The MMP-2 expression was inhibited in dependence to the mass of radish-extract treated. In conclusion, the supercritical heat-treated radish-extract has an effect on improving skin wrinkles not only when it is applied to the skin but also when orally ingested. Thus, it can be effectively used as a composition to health functional products. Thereafter, we can also conclude that radish, a food that does not show any side-effects even upon long-term intake, can reduce wrinkle formation as well as improve skin elasticity when taken regularly for a long period.

• Korean Journal of Food Science and Technology
• /
• v.40 no.5
• /
• pp.522-527
• /
• 2008

Low molecular peptides were isolated from Asterias amurensis via SDS-PAGE. The peptides were separated via consecutive gel filtration as five fractions (F1-F5) according to molecular weights, based on the results of MALDI-TOF MS analysis. The molecular weight of the most active peptide was estimated as 15,000 daltons. The peptide showed cytotoxicity on normal human fibroblast cells at levels as low as 20% when 1.0 mg/mL of the samples was added. The peptide also exhibited higher levels of nitric oxide production from macrophages than the lipopolysaccaharides. It was determined that prostaglendin $E_2$ production was significantly inhibited, up to 127.8% as compared to the control. The low molecular peptide inhibited hyaluronidase activity as 535.7 ${\mu}g/mL$ of $IC_{50}$. It can be concluded that the relatively low molecular weight peptide, fucoidan, from A. amurensis has excellent cosmetic and immunomodulatory activities, which can be considered as a possible resource of new cosmetic agents for skin immunomodulation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.95-95
• /
• 2018

강재의 방식법 중 도장은 부식을 억제하는데 효과적이고 편리한 방법으로 선박 및 해양 강 구조물의 방식법으로 사용되고 있다. 한편, 강 구조물의 효율적인 유지관리를 위해서는 방식 도장의 도막 열화도를 평가하고 잔존 수명을 예측하여 최적 시기에 보수도장 혹은 재도장하는 것이 필요하다. 일반적으로 선박 및 해양구조물에 적용되는 도막의 방식 성능 평가 방법으로 해수 침지 시험, 염수 분무 시험, 옥외 폭로 시험 등이 있다. 그러나 이러한 시험들은 그 시험 방법에 따라서 정량적인 평가에 한계가 있음은 물론 장기간 소요되는 등 곤란한 문제점이 있다. 그러므로 선박 및 해양구조물을 비롯하여 교량, 각종 강 구조물의 도장 방식에 사용되는 방식용 도료의 성능을 단기간에 적절하게 평가할 수 있는 가속시험법이 제시되며 연구-사용되고 있다. 그 중 도막 방식 성능을 보다 효율적, 비파괴적, 정량적으로 평가할 수 있는 임피던스 분광법(EIS)과 같은 전기화학적 방법은 상대적으로 시험 기간을 크게 단축시킬 수 있고, 대상 방식 도장의 미세한 성능 차이도 분별 가능하다는 장점이 있다[1]. 따라서 본 연구에서는 선박 및 해양구조물 등 가혹한 부식환경에서 강력한 내구성을 가질 수 있도록 다양한 종류의 표면처리 도장 시편을 제작하여 자외선 조사-염수분무-침지환경 등의 열악한 환경조건 하에서 부식-열화 촉진 시험을 실시하였다. 그리고 그 촉진 열화 과정에서 도막의 외관 상태를 관찰 분석함은 물론 전기화학적 임피던스 분광법을 병행 측정하며 그 표면막의 부식 및 도막 열화도를 비교-종합 평가하였다.본 연구에 사용된 시편은 Al 및 Zn 도금 강판에 에폭시, 에폭시-실리콘 우레탄, 에폭시-우레탄 도장 시편으로 Scribe, No Scribe 및 비교재 Al 및 Zn 도금 시편으로 분류하여 각각 실험을 진행하였다. 즉, 도막 열화 시험은 복합 노화 시험법으로 UV 조사 36 시간(ASTM G53), 염수분무 32 시간(ISO 7253), 수분 응축 10 시간을 1 Cycle로 100 Cycle(7800 시간) 동안 실험을 진행하였다. 이때 도막 열화도 평가는 전기화학적 임피던스 분광법을 이용하여 각 실험 조건별로 주파수에 따른 임피던스(Z) 값을 평가하였다. 즉, 상온 $25^{\circ}C$의 3.5% NaCl 100 ml 수용액에 작동 전극(Working Electrode)과 구리 도선을 통해 연결하였고, 노출 면적은 $1cm^2$로 일정하게 유지 하였으며, 상대 전극(Counter Electrode)은 탄소봉, 기준 전극(Reference Electrode)으로 포화카로멜전극(Saturated Calomel Electrode)을 사용하여 측정하였다. No Scribe 시편의 경우에는 Al 기판 에폭시-실리콘 우레탄 도장 시편이 우수한 도막 저항성을 나타내었으며, 에폭시-우레탄 도장시편은 23사이클 이후의 저항값이 가장 낮게 나타났다. Zn 기판의 경우는 에폭시, 에폭시-실리콘 우레탄, 에폭시-우레탄 도장 시편 모두 저항 값이 유사하였으며, Al 및 Zn 도금 시편은 도장 처리된 시편에 비해 훨씬 낮은 저항 값을 보였다. 또한 Scribe 시편의 경우에는 Al 기판 에폭시-실리콘 우레탄 도장 시편에서 높은 초기 저항 값을 보였으며, 23 사이클 후의 저항 값은 세 종류의 도막에서 약 1~0.1 Gohm 으로 나타났다. 그리고 Zn 기판 에폭시-실리콘 우레탄 도장 시편에서 가장 낮은 도막 저항 값이 나타났다. 이상의 실험을 통해서 본 연구 내용은 실내촉진시험으로 선박 및 해양 강 구조물에 사용되는 다양한 종류의 도막의 열화도를 평가하는 기초 설계 지침으로 응용될 수 있을 것으로 사료된다. 한편, 도막은 노출 환경에 따라 방식 성능이 다르므로 실제 도막의 사용환경을 고려하여 도장 사양별 적용 부위에 따른 적정 가속 실험 방법을 선정할 필요가 있다고 사료된다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.37 no.4
• /
• pp.351-356
• /
• 2011

Citrus unshiu (C. unshiu) Markovich were dried peel of mandarin orange, of which fresh fruit was one of the famous foods in Korea and Eastern Asia. In the oriental medicine, C. unshiu peel was known to have a diuretic effect and to strengthen spleen function. Recently, natural flavonoids of C. unshiu peel have been investigated. In this study, C. unshiu peel extract containing flavonoid-glycosides was cultured with Schizophyllum commune (S. commune) mycelia producing ${\beta}$-glu- cosidase and its biological activities were investigated. ${\beta}$-glucosidase of S. commune mycelia converted the flavonoid-glycosides (rutin and hesperidin) into aglycones (naringenin and hesperetin). Fermented C. unshiu peel extract compounds were analyzed by HPLC system. The photoprotective potential of fermented C. unshiu peel extract was tested in human dermal fibroblasts (HDFs) exposed to UVA. Fermented C. unshiu peel extract extract also showed notable in vitro anti-inflammatory effect on cellular systems generating cyclooxygenase-2 (COX-2) and 5-lipoxygenase (5-LOX) metabolites. Also, UVB-induced production of interleukin-$1{\alpha}$ in human HaCaT cells was reduced in a dose-dependent manner by treatment with fermented C. unshiu peel extract. These results suggest that fermented C. unshiu peel extract may mitigate the effects of photoaging in skin by reducing UV-induced adverse skin reaction.