• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.9-14
• /
• 2020

In this paper, we studied on-board antenna(primary link/secondary link/satellite link) used in UAV Data-link system. As a result, it is ideal to configure the Data-link as a triple link to secure the flight stability of the UAV, but the communication link should be configured according to the operating platform. As a result of overseas R&D trend analysis, the on-board Data-link antenna is installed and operated in a location where it is easy to secure LOS. The primary link consists of a directional antenna for basic operation and an omni-directional antenna for emergency operation. The secondary link uses a monopole/dipole antenna in the UHF/C band. Satellite link has been developed to apply phased array antenna to improve UAV operability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.688-693
• /
• 2009

In this paper, a half wave-length microstrip antenna was proposed to be able to continuously tune the resonant frequency in the stated area of UHF ISM band. By loading varactor diodes at both edges of the half wavelength antenna, where the electric field is the strongest, and varying the voltage in order to tune the electrical resonance length continuously, it is possible to automatically recover the resonant frequency and input impedance shifted by surrounding environment. When the microstrip antenna(center resonant frequency: 425 MHB) was tested, by adjusting the each voltages of varactor diodes from DC 0.6 to BC 3.0 volts, the resonant frequency under 20 dB return loss was varied 385 to 465 MHz. The peak gain was -0.2 dBd and return loss -10 dB bandwidth was 3.3 MHz(0.8 %).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.490-499
• /
• 2006

In this paper, we present the newly developed propagation toss model of a long range maritime communication channel, measured by a ground to air flight test, and discuss its validity compared with the predictive value based on the spherical earth reflection model. To measure the propagation loss, actual flight test was performed in the Yellow Sea and the measurement of receiving signal strength was made for overall test range. As far as the test condition is concerned, it is expected that the receiving signal strength must be interfered with the reflected wave by an island existing around the reflection point. Therefore we introduce some modifications on the conventional spherical earth reflection model by including the effect due to the reflected wave from the island. And then, we compare the path loss measured by flight test with that one analyzed by the spherical earth reflection model accounting for reflected wave of the island. As a result of the comparison, it is verified to predict the path loss accurately by the spherical earth reflection model including the effect due to the reflected wave from an island for a long range ground to air communication.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.69-75
• /
• 2010

In this paper, with using the clapp type VCO(Voltage Controlled Osillator) configuration a wideband frequency synthesizer in UHF band is proposed. In order to design a wideband frequency synthesizer, the variation of phase in the negative resistance circuit as well as the load circuit was analyzed. Based on this result we propose a method to widen the operation range of the VCO. A frequency synthesizer using the proposed wideband VCO was designed and fabricated. It is shown that the synthesizer has the operating frequency range of 740~1,530 MHz by 0~5 V varactor tuning voltage, and it had the output power of 2~-6 dBm. Moreover, the phase noise measured as -77 dBc/Hz at 10 kHz offset, and as -108 dBc/Hz at 100 kHz offset from the oscillation frequency.

• Journal of Biosystems Engineering
• /
• v.33 no.3
• /
• pp.204-209
• /
• 2008

The power strength of electric wave of reader looked radiation forms from the gate type RFID system. The more distant from antennas, the weaker of power strength of electric wave. The power strength of electric wave with 3 antennas showed stronger than its with 2 antennas. With 2 antennas, the coefficient of correlation between the power strength of electric wave and response ability of tag was 0.665 (p=0.009), and it showed results at significance level. With 3 antennas, the coefficient of correlation was 0.711 (p=0.004), correlationship between the power strength of electric wave and the response ability of tag showed at significance high level. From the analysis result about tag reading performance on the gate type RFID system, the reading rate was good when tags were attached on a acrylic plate which were located in front of 3 or 4 antennas. As tags were getting away from antennas, the reading rate was decreased. The nearer from antennas, the higher the reading rate at the center. When tags were turned at right angles with antennas, the longer distant from antennas, the lower reading rates at the center, right and left locations. When the number of antennas and distance are constant, respectively, the significant difference of the tag reading rates according to the locations of left, right and center were not found.

• Journal of Advanced Navigation Technology
• /
• v.20 no.1
• /
• pp.45-52
• /
• 2016

In this paper, the method of interference analysis and its simulation have been suggested for the frequency sharing between aeronautical radio navigation systems and Link-16 platforms. In order to get the criteria for interoperability, the algorithm of interference analysis and protection ratio are derived to assure frequency sharing. Also the receiving power of wireless system has been illustrated with the help of radio propagation model of ITU-R Rec. P.1546 in VHF-UHF band. Finally the required receiving power or separation distance between DME/TACAN beacons and Link-16 ground station terminals has been considered based on system link budget in terms of evaluating interoperability as well as actual applications. As a result, if the suggested interference analysis and test set-up are applied to the field trial, it will lead to easy means to make a decision on interoperability over the existing incumbent systems.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.6
• /
• pp.51-61
• /
• 2007

In this paper, Air-interface protocols of ISO 18000-6 Types and EPCglobal Classes applied to RFID system in UHF band are analyzed, and those anticollision algorithms are realized. Also, the each algorithm which improves the performance of standard protocol is proposed, and the performance is compared when clock period of link timing is a identical condition on $12.5{\mu}s$. As the result, when 500 tags exist simultaneously inside reader interrogation zone, the tag recognition performance of a standard protocol is better in preceding order of Class-1 Generation-1, Type B, Type A, Class-0 and Class-1 Generation-2. And also the performance of improved protocol is better in ascending order of Type B, Type A, Class-1 Generation-1, Class-0 and Class-1 Generation-2. Therefore, performance of tag recognition remarkably depends on the regulated clock period in the protocol and link timing between a reader and a tag.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.5
• /
• pp.20-27
• /
• 2007

In this paper, Air-interface protocols of ISO 18000-6 Type A and B applied to RFID system in UHF band are analyzed, and those algorithms are realized. Also, the improved anticollision algorithms for the Type A and B of ISO 18000-6 protocol are proposed and the performances are compared. As the results, reduction ratio of total tag recognition time of the improved ISO 18000-6 Type A algorithm is 35.2 % for 100 tags and 24.3% for 1000 tags with respect to standard algorithm, respectively. And the reduction ratio of the improved ISO 18000-6 Type B algorithm is 6.0% for 100 tags and 6.6% for 1000 tags. Therefore, the improved anticollision algorithm proposed in this paper is the advanced method improving the performance of tag recognition in the RFID system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.954-963
• /
• 2007

As RFID systems are applied to various fields and applications such as supply chain management, asset management, location based applications etc. the requirements becomes diverse. For example, Much higher performance, TCP/IP protocol stack are required in some applications. However, low end processors based systems such as 8051 processor can not meet such requirements due to their low processing capacity and limited size of memory. In this paper a UHF band RFID system which meets the EPC Class-1 Generation-2 specification with ARM920T-based processor is implemented and tested.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.31-36
• /
• 2007

In the RFID system, one of the important criteria of tag antenna performance is the detection distance. The most important factor determining the detection distance of the tag antenna is the Radar Cross Sections(RCS). In this paper, we propose a method to simply measure the RCS of the RFID tag antenna using two reader antennas(Tx and Rx) and a network analyzer. We estimate RCS' from the RCS equation based on the measured $S_{21}$ using the network analyzer. We compare the measured $S_{21}$ values with the calculated $S_{21}$ values and the simulated $S_{21}$ values using EM simulator. The used tag antennas are two kinds of dipole-type, metal-type, and an inductively-coupled type ones. In case of the dipole type, the measured, simulated and calculated values of the RCS are almost the same. In case of other types, we obtain the measured RCS values with a difference of about 3 dB.