• Journal of Fashion Business
• /
• v.10 no.1
• /
• pp.58-78
• /
• 2006

This study materializes body type measurement based on ISO(International Standard Organization)size system, targeting 1381 Chinese women, and suggests clothes size standards. It provides basic information on Chinese women size for Korean clothes companies advanced in China to strengthen the national competitiveness of Korean clothing industry. First, after the body type examination, based on the ISO's drop value, the results of types are in its decreasing order: A, M, H, and D. Second, women upper garment sizes by body types are set in the section of height 152cm, 160cm, and 168cm. Garment sizes are suggested based on the section that has more than 0.8% of appearance rate for the survey target: A, H, and M. Third, the clothes sizes of women pants are set in the section of height 152cm, 160cm, and 168cm just with the same as the upper garment.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.43-52
• /
• 2005

The effect of fuel injection spray on engine performance has been known as one of the major concerns for improving fuel economy and reducing emissions. In general, reducing the spray droplet size could prevent HC emission in gasoline engine. As far as PFI (Port Fuel Injection) gasoline engine is concerned, the mixture of air and fuel may not be uniform under a certain condition, because breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve. This study, by constituting PFI gasoline spray system, was performed to study the transient spray characteristics and dynamic behavior of droplets from 2hole 2spray type injector used in DOHC gasoline engine. Mean droplet size and optical concentration in accordance with various conditions were measured by LDPA and CCD camera. Through this study, the variation of drop size and optical concentration could be used for understanding the behavior of unsteady spray was declared and the existing the small droplets between each pulse spray could be estimated caused to the development of wall film was conformed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.41-48
• /
• 2001

This paper was made to evaluate the effect of the type of latex for coating on the printability by investigating the structure of pore such as the pore fraction, the number of pores, pore size and distribution of coated paper. The coated structure is mainly depend on the results of interaction between pigment and binder. It means that the structure of pore formed is chiefly affected by the type of latex. This physical properties of pore have a close relation with ink set-off associated with the drying rate, the speed of penetration of ink into base paper and printing gloss. Therefore it was necessary to find out the relationship between pore structure and the performance of printability by modifying the type of latex to vary the pore structure of coated paper. Acrylic latex was superior to S/B latex in the sedimentation volume, compressibility, smoothness, pore fraction and its number, the weight of transferred ink onto the coated paper and ink repellance. In contrast, water retention and ink setting were not good. in the comparison of anionic and amphoteric latex, amphoteric latex showed better performance in the thickness, smoothness, pore fraction and its number, pore size, the weight of ink transmitted and K&N ink receptivity, etc.

• Journal of ILASS-Korea
• /
• v.16 no.1
• /
• pp.27-36
• /
• 2011

The impact force on the single and overlap region of twin spray was experimentally evaluated using visualization method in full cone type swirl nozzle spray. Visualization of spray was conducted to obtain the spray angle and breakup process. The photography/imaging technique, based on Particle Image Velocimetry (PIV) using high-speed camera, was adopted for the direct observation of droplet motion and axial velocity measurement, respectively. Droplet size was measured by Particle Motion Analyze System (PMAS). The purpose of this study is to provide fundamental information of spray characteristics, such as impact force, for higher etching factor in the practical wet etching system. It was found that the spray angle, axial velocity and impact force were increased with increasing the nozzle pressure while droplet size decreased with increasing the nozzle pressure. Droplet size increased as the distance from nozzle tip was decreased. The impact force of twin spray in the overlap region was about 63.29, 67.02, 52.41% higher than that of single spray at 40, 50 and 60 mm of nozzle pitch, respectively. Also, the nozzle pitch was one of the important factors in the twin spray characteristics.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.572-576
• /
• 2003

Open/closed porosity, pore size and its distribution and pore type as a funtion of sintered density of UO$_2$-20 wt％CeO$_2$ pellets were investigated. Pore appeared almost closed-type with the density above 96％ of the theoretical density. Bimodal pore size distribution was observed regardless of the sintered density, but the number of pore decreased with increasing the sintered density. The shape of pore was changed from irregular shape to round type with increasing the sintered density.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.163-171
• /
• 1999

The abnormal grain coarsening in wire rolling induces detrimental defects, such as jagged size tolorance, severe bending after heat treatments and drawing troubles, in the following secondary processes. Neishi et al observed that there is a band type region where grain coarsenting occurs in the plastic strain vs. deformation temperature plot. Based on the finding, we have investigate whether grain sizes and ferrite volume fractions are correlation to deformation strain with three kinds of wire rod diameters as for the different average deformation conditions. The samples were chosen from the No.2 Wire Rod Mill of POSCO where 3-roll type of finishing mill stand are used. It was found in the present work that the grain size and ferrite volume fraction of the rolled and cooled microstructure were changed with rolling reduction and rolling temperature. Abnormally grown grains at various observed points were also found. To have homogeneously fine grains of microstructure from the No. 2 Wire Rod Mill, it will be easier to control finish rolling temperature at around 750$^{\circ}C$ rather than to find another rolling schedule.

• Particle and aerosol research
• /
• v.9 no.1
• /
• pp.23-29
• /
• 2013

Inertial impaction type mist eliminators are the most effective instruments to separate mist from the gas. In this work, the effect of the horizontal chevron type mist eliminators is characterized experimentally. Droplet size distribution and evaluation of removal efficiency of the chevron type mist eliminators at different gas flows were investigated using an aerosol particle size analyzer and a portable aerosol spectrometer, respectively. The experimental investigations showed that the mist removal efficiency in these instruments is dependent in the droplet size, and the pressure drop is nil.

• Journal of Families and Better Life
• /
• v.2 no.1
• /
• pp.165-177
• /
• 1984

The purpose of this study was to investigate satisfaction with the function of interior space of apartment and factor which influence it, and then to provide housing practitioners with basic data for more desirable apartment interior environment. On the basis of the review of literature, questionnaire was developed. The sample was classified into type of unit floor plan and house size of 17 districts in Seoul. 139 households were selected in three districts which were the first three regions of high apartment density. Data were analyzed by computer using frequency, percentage, mean, standard deviation, F-test, Duncans multiple range test, η2 , person's product moment correlation coefficient. the results are as follows: Factors which influence satisfaction with the functionality of interior were household size and family life cycle as sociodemographic variable, and type of unit floor plan as physical variable. It was shown that the satisfaction with the functionality of interior was related to satisfaction with the external environment. More specifically, (1)the smaller a household size was the more the owner became satisfied. (2)households were in the stage of establishment in the family life cycle and households with C type of unit floor plan showed higher degree of satisfaction. (3) satisfaction with the functionality of interior had positibly related to satisfaction with the external environment.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.5
• /
• pp.691-702
• /
• 2002

The purpose of this study was to provide basic information on the propriety of the ready to wear garment sizes of Tween Generation(ages from 5th grade to 8th grade) who has different clothing preferences in color, styles, and design and also different body sizes and shapes from younger and older students. The objectives of the study were to ascertain (a) the body figure changes occurring during Tween Generation; (b) the coverage of manufactures'garment sizes. The body measurements of elementary school students(5th & 6th grades) and junior high school students(7th & 8th grades) provide the basic statistics for this study. The mean differences of each size within each figure type are compared by using t-teats. The differences in various manufacturers'apparel sizing and figure size are investigated. Also the body measurements and the apparel sizes of the manufacturers are compared in order to evaluate the suitability of the garment size. Results indicate that the body type factors are different in each age group. And manufactures'sizes come out to be much smaller than the actual body measurements. Young casual wear can cover junior high school students satisfactorily but for elementary school students, because of low drop-value, the overall satisfaction with filling is low.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.70-74
• /
• 2004

There are many researches being in process to develop the information storage devices applying to the portable devices recently. Based on this need, the information storage devices have to be satisfied with the fast access time, the robustness of the system, high data transfer rate and lower media price. The total size of the drive must design to adapt the portable devices such as CF II card or PC II card size. This paper proposes the swing arm type actuator to insert the designed actuator in the drive of the CF II size. Hereafter the research will be going on to be suitable to the physical standard and design the focus magnetic circuit newly. The swing arm type actuator including this circuit is designed to have the dynamic characteristic satisfying the mechanical specification as well as the BD 1x. Finally, the adaptability to the portable devices was demonstrated by the finite element analysis and optimization of structural part.