• Structural Engineering and Mechanics
• /
• 제10권3호
• /
• pp.289-298
• /
• 2000

Based on the two-dimensional constitutive relationship of the piezoelastic material, this paper derived an analytic solution to the elastic beam with the piezoelectric layer under the electric field, presented the explicit expressions of its displacement and stress. It is helpful for understanding the electrical and mechanical behavior of piezoelectric materials as actuators and the validation of the numerical methods such as FEM.

• 센서학회지
• /
• 제19권2호
• /
• pp.130-136
• /
• 2010

The microbolometer array sensor with fine pitch pixel array has been implemented to the released amorphous silicon layer supported by two contact pads. For the design of focal plane mirror with geometrical flatness, the simple beam test structures were fabricated and characterized. As the beam length decreased, the effect of beam width on the bending was minimized, Mirror deformation of focal plane in a real pixel showed downward curvature by residual stress of a-Si and Ti layer. The mirror tilting was caused by the mis-align effect of contact pad and confirmed by FEA simulation results. The properties of bolometer have been measured as such that the NETD 145 mK, the TCR -2 %/K, and thermal time constant 1.99 ms.

• Advances in materials Research
• /
• 제11권1호
• /
• pp.41-57
• /
• 2022

This paper is focused on delamination analysis of a multilayered inhomogeneous viscoelastic beam subjected to linear creep under constant applied stress. The viscoelastic model that is used to treat the creep consists of consecutively connected units. Each unit consists of one spring and two dashpots. The number of units in the model is arbitrary. The modulus of elasticity of the spring in each unit changes with time. Besides, the modulii of elasticity and the coefficients of viscosity change continuously along the thickness, width and length in each layer since the material is continuously inhomogeneous in each layer of the beam. A time-dependent solution to the strain energy release rate for the delamination is derived. A time-dependent solution to the J-integral is derived too. A parametric analysis of the strain energy release rate is carried-out by applying the solution derived. The influence of various factors such as creep, material inhomogeneity, the change of the modulii of elasticity with time and the number of units in the viscoelastic model on the strain energy release rate are clarified.

• 전기학회논문지
• /
• 제60권1호
• /
• pp.114-118
• /
• 2011

Dye-Sensitized Solar Cells(DSSCs) consist of a titanium dioxide($TiO_2$) nano film of the photo electrode, dye molecules on the surface of the $TiO_2$ film, an electrolyte layer and a counter electrode. But two transparent conductive oxide(TCO) substrates are estimated to be about 60[%] of the total cost of the DSSCs. Currently novel TCO-less structures have been investigated in order to reduce the cost. In this study, we suggested a TCO-less DSSCs which has titanium double layer electrodes. Titanium double layer electrodes are formed by electron-beam evaporation method. Analytical instruments such as electrochemical impedance spectroscopy, scanning electron microscope were used to evaluate the TCO-less DSSCs. As a result, the proposed structure decreases energy conversion efficiency and short-circuit current density compared with the conventional DSSCs structure with FTO glass, while internal series impedance of TCO-less DSSCs using titanium double layer electrodes decreases by 27[%]. Consequently, the fill factor is improved by 28[%] more than that of the conventional structure.

• 한국재료학회지
• /
• 제29권4호
• /
• pp.271-276
• /
• 2019

Oxide-dispersion-strengthened (ODS) alloy has been developed to increase the mechanical strength of metallic materials; such an improvement can be realized by distributing fine oxide particles within the material matrix. In this study, the ODS layer was formed in the surface region of Zr-based alloy tubes by laser beam treatment. Two kinds of Zr-based alloys with different alloying elements and microstructures were used: KNF-M (recrystallized) and HANA-6 (partial recrystallized). To form the ODS layer, $Y_2O_3$-coated tubes were scanned by a laser beam, which induced penetration of $Y_2O_3$ particles into the substrates. The thickness of the ODS layer varied from 20 to $55{\mu}m$ depending on the laser beam conditions. A heat affected zone developed below the ODS layer; its thickness was larger in the KNF-M alloy than in the HANA-6 alloy. The ring tensile strengths of the KNF-M and HANA-6 alloy samples increased more than two times and 20-50%, respectively. This procedure was effective to increase the strength while maintaining the ductility in the case of the HANA-6 alloy samples; however, an abrupt brittle facture was observed in the KNF-M alloy samples. It is considered that the initial microstructure of the materials affects the formation of ODS and the mechanical behavior.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.754-758
• /
• 2010

In general, Dye-sensitized Solar Cells(DSCs) consist of the nanocrystalline titanium dioxide($TiO_2$) layer which is fabricated on a transparent conductive oxide(TCO) layer such as $F/SnO_2$ glass, a dye adhered to the $TiO_2$, an electrolyte solution and platinum-coated TCO. Among these components, two TCO substrates are estimated to be about 60% of the total cost of the DSCs. Currently novel TCO-less structures have been investigated in order to reduce the cost. In this study, TCO-less DSCs consisting of titanium electrodes were investigated. The titanium electrode is deposited on top of the porous $TiO_2$ layer using electron-beam evaporation process. The porosity of the titanium electrode was found out by the SEM analysis and dye adhesion. As a result, when the thickness of the titanium electrode increased, the surface resistance decreased and the conversion efficiency increased relatively.

• 한국음향학회지
• /
• 제34권6호
• /
• pp.470-478
• /
• 2015

음선 모델링에서 다층 해저 바닥을 고려하는 경험적 방법 중 하나는 단일층 가정으로써, 다층 구조에 대한 평면파 반사계수를 사용하는 것이다. 본 연구자는 이층 해저 바닥에 대해 단일 층 가정의 유효성을 조사하고, 음속비, 송수신 거리 당 층 두께, 1차 반사파의 스침각의 함수로 표현되는 간단한 부등식 조건을 얻었다. 부등식 조건으로부터, 단일 층 가정이 실제 해양 환경의 중주파수 음선 모델링에 적용될 수 있음을 보였다. 마지막으로 한국 동해와 유사한 해양환경에 대해 수치실험을 수행하였다. 다층 해저 바닥에 대한 평면파 반사계수를 적용한 기하학적 빔 모델을 이용하여 비상관 전달손실을 계산하고, 서울대학교에서 개발한 포물선 방정식 패키지인 SNUPE 2.0의 결과와 비교하였다.

• Steel and Composite Structures
• /
• 제46권2호
• /
• pp.203-210
• /
• 2023

In the present research, dynamic deflections of a sandwich beam having functionally graded (FG) porous core have been investigated assuming that the sandwich beam is exposed to a pulse load of blast type. The two layers of sandwich beam have been made of a polymeric matrix reinforced by graphene oxide powder (GOP). The micromechanical formulation of the layers has been done via Halpin-Tsai model. The solution method is chosen to be Ritz method which is an efficient method to solve the system of equations of beams modeled based on a higher-order theory. To derive the time history of sandwich beam under pulse load, Laplace method has been used. The porosity content of the core, the GOP content of the layers, thickness of the layer and also duration of the applied load have great influences of the responses of sandwich beam.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.768-773
• /
• 2016

엔진 밸브 시트와 페이스는 엔진 성능에 영향을 미치므로 내마모성, 내열성 및 내식성이 요구된다. 이러한 특성을 갖는 표면층을 형성하기 위해 일반적으로 PTA 프로세스를 사용하고 있지만 넓은 열 영향부와 높은 모재 희석 등과 같은 문제가 발생한다. 이러한 단점을 개선한 레이저 클래딩은 희석률이 낮고 열 영향 및 열 변형을 최소화하므로 더욱 우수한 클래드 층을 형성할 수 있다. 하지만 레이저 빔의 특성상 넓은 면적을 클래딩 할 경우, 1 패스 클래드 층의 중첩이 불가피하다. 중첩률 기준을 빔 사이즈와 클래드 층 폭으로 나누어 멀티패스 클래드 층을 형성한 결과, 기준에 관계없이 중첩률이 증가할수록 클래드 층의 폭이 감소하고 높이가 증가하였다. 하지만 빔 사이즈 기준 중첩률 조건으로 형성된 멀티패스 클래드 층이 다른 기준보다 모재 희석이 감소하여 더욱 높은 경도 값을 나타내었다. 결론적으로, 중첩률 기준을 클래드 층 폭으로 할 경우, 클래드 층 형상에 영향을 주는 공정변수가 변할 때 마다 폭의 길이가 달라지기 때문에 빔 사이즈를 중심으로 중첩률을 정의하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.45-48
• /
• 2003

BiSrCaCuO thin films were fabricated by atomic layer-by-layer deposition using an ion beam sputtering method. 10 wt% and 90 wt% ozone mixed with oxygen were used with ultraviolet light irradiation to assist oxidation. At early stages of the atomic layer by layer deposition, two dimensional epitaxial growth which covers the substrate surface would be suppressed by the stress and strain caused by the lattice misfit, then three dimensional growth takes place. Since Cu element is the most difficult to oxidize, only Sr and Bi react with each other predominantly, and forms a buffer layer on the substrate in an amorphous-like structure, which is changed to $SrBi_2O_4$ by in-situ anneal.