• International Journal of Highway Engineering
• /
• v.16 no.1
• /
• pp.49-56
• /
• 2014

PURPOSES : This study was done to model the headway distribution of rural two lane roads. METHODS : Time headway data for the various level of traffic volumes was measured in twelve sites. Based on the time headway data, existing seven mathematical models were evaluated and selected by comparing graphically the measured and theoretical distributions and conducting the Chi-square test. RESULTS : The results show that both the Schul model and Composite Model were the most appropriate models of the models. Based on the measured time-headway distributions, this study proposed a new headway distribution model by the shift of the Schul model. CONCLUSIONS : The shifted Schul model has the ability to describe time headway distirbutons for random, intermediate, and constant-headway states.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.4D
• /
• pp.305-311
• /
• 2012

With the rapid deployment of hipass$^{(R)}$, the congestion is inevitable due to the operation of the hipass lane system. Recently, SMART Highway project have developed a multi-lane mainline tolling system, called SMART Tolling system. To analyze the effectiveness of the system in terms of capacity, this study tries to estimate the capacity and its improvement of multi-lane tolling system based on current hipass$^{(R)}$ data. The methodology uses the saturation time headway. This follows three steps; 1) estimate the saturation time headway, using hipass$^{(R)}$ data, and capacity. 2) estimate two factors (the first one is dividing the one side lane width and lateral clearance factor ($f_w$) into two side one, the second one is dividing the capacity of hipass lane operating a circuit breaker into the capacity of hipass lane not operating, the last one is increasing factor of lane width). 3) calculate the capacity of multi-lane mainline tolling system. The results of method produced 2172~2187 veh/hour as smart tolling capacities, respectively. Those are higher about 370 veh/hour than the values from existing literature reviews. Additionally, saturation time headways were identified as lower by 0.5 seconds/veh than existing headways based on hi-pass$^{(R)}$ based one, which naturally implies the improvement in capacity. Some limitations and future research agenda have also been discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.68-74
• /
• 2001

A lane detection based on a road model or feature all needs correct acquirement of information on the lane in an image. It is inefficient to implement a lane detection algorithm through the full range of an image when it is applied to a real road in real time because of the calculating time. This paper defines two (other proper terms including"modes") for detecting lanes on a road. First is searching mode that is searching the lane without any prior information of a road. Second is recognition mode, which is able to reduce the size and change the position of a searching range by predicting the position of a lane through the acquired information in a previous frame. It allows to extract accurately and efficiently the edge candidate points of a lane without any unnecessary searching. By means of inverse perspective transform which removes the perspective effect on the edge candidate points, we transform the edge candidate information in the Image Coordinate System(ICS) into the plan-view image in the World Coordinate System(WCS). We define a linear approximation filter and remove faulty edge candidate points by using it. This paper aims at approximating more correctly the lane of an actual road by applying the least-mean square method with the fault-removed edge information for curve fitting.e fitting.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2843-2845
• /
• 2000

A lane detection based on a road model or feature all need correct acquirement of information on the lane in a image, It is inefficient to implement a lane detection algorithm through the full range of a image when being applied to a real road in real time because of the calculating time. This paper defines two searching range of detecting lane in a road, First is searching mode that is searching the lane without any prior information of a road, Second is recognition mode, which is able to reduce the size and change the position of a searching range by predicting the position of a lane through the acquired information in a previous frame. It is allow to extract accurately and efficiently the edge candidates points of a lane as not conducting an unnecessary searching. By means of removing the perspective effect of the edge candidate points which are acquired by using the inverse perspective transformation, we transform the edge candidate information in the Image Coordinate System(ICS) into the plane-view image in the World Coordinate System(WCS). We define linear approximation filter and remove the fault edge candidate points by using it This paper aims to approximate more correctly the lane of an actual road by applying the least-mean square method with the fault-removed edge information for curve fitting.

• Journal of Korean Society of Transportation
• /
• v.1 no.1
• /
• pp.56-63
• /
• 1983

Intersection control has dual-purposes; increasing capacity and reducing delay. The primary concern of efficient intersection control under oversaturated condition as in Korea is to increase capacity. Prevailing intersection operation technique permits thru traffic to utilize left turn lane, because the intersection without left turn pocket has left turn signal interval. In this situation, it seems not to be valid to calculate capacity, delay, and signal timings by conventional methods. By critical lane technique, capacity increases as cycle length increases. However, when thru traffic utilize LT lane, the capacity varies according to LT volume, LT interval as well as cycle length, which implies that specific cycle length and LT interval exist to maximize capacity for given LT volume. The study is designed is designed to calculate utilization factors of LT lane for thru traffic and capacities, and identify signal timings to yield maximum capacity. The experimental design involved has 3 variables; 1)LT volumes at each approach(20-300 vph), 2)cycle lengths (60-220 sec), and 3)LT intervals(2.6-42 sec) for one scenario of isolated intersection crossing two 6-lanes streets. For LT volume of 50-150 vph, capacity calculated by using the utilization factor is about 25% higher than that by critical lane method. The range of optimum cycle length to yield maximum capapcity for LT volume less than 120 vph is 140-180 sec, and increases as LT volume increases. The optimum LT interval to yield maximum capacity is longer than the intrval necessary to accommodate LT volume at saturation flow rate.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.2
• /
• pp.48-61
• /
• 2020

The objective of this study is to estimate traffic capacity based on the heavy-vehicle ratio in a two-lane freeway work zone where one lane is blocked by construction. For this, closed circuit television (CCTV) video data of the freeway work zone was collected, and the congestion at an upstream point was observed. The traffic volume at a downstream point was analyzed after a bottleneck was created by the blockage due to the upstream congestion. A distribution model was estimated using observed-time headway, and the road capacity was analyzed using a goodness-of-fit test. Through this process, the general capacity and an equation for capacity based on the heavy-vehicle ratio passing through the work zone were presented. Capacity was estimated to be 1,181~1,422 passenger cars per hour per lane (pcphpl) at Yeongdong, and 1,475~1,589pcphpl at Jungbu Naeryuk. As the ratio of heavy vehicles increased, capacity gradually decreased. These findings can contribute to the proper capacity estimation and efficient traffic operation and management for two-lane freeway work zones that block one lane due to a work zone.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.5
• /
• pp.124-134
• /
• 2011

To make popular the NEV(Neighborhood Electric Vehicles) uses, it must be considered the supply of infrastructure and the political decision for NEV. However, the guidelines of infrastructure for NEV are not prepared. The guidelines of infrastructure for NEV should be performed in many research and case. The purpose of this study is to reveal the influence of NEV on the two-lane highway traffic flows by TWOPAS simulation model. The main items to check the influence are Average Travel speed, Percent Time Spent Following and Total Delay. The scenario were setup by traffic volume. And the NEV percentages are changed from 1% ~ 30%. The scenario 1 which traffic volume are 650veh/h and the scenario 4 which traffic volume are 2,600veh/h are less influenced by NEV, compare to scenario 2, scenario 3. Because the scenario 1 is more free to make passing other cars and Scenario 4 is fully saturated with existing traffic volumes. The urban two-lane highway which has much traffic volume and the rural two-lane highway which has little traffic volume has affinity for NEV than the other two-lane highway.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.2
• /
• pp.85-94
• /
• 2016

Lane Designation is defined as reasonable road management to ensure the road safety and enhance road efficiency. While the lane designation system was abolished in 1999, it was redefined because of the increasing number of large vehicles in the passing lane, violent on driving and traffic accidents in 2000. The needs of improvement on operating the lane designation has been increasing more in recent due to the low ratio of compliance with the system and difficulties to keep the right lane due to need of turning and demand of widening of designates lane for two-wheeled vehicles and truck. In this study, we presented the improvement plan through the question survey, simulation analysis, safety evaluation. It found a problem that the low-speed vehicle is to use the upper level roadway, difficulties of supervision, the imbalance in the lane use, imbalance traffic and does not match the international standards. This study suggested five different alternatives through the survey. micro simulation has used in order to examine each alternative by management effectiveness and feasibility. It analyzed the traffic speed, efficiency, traffic balance of alternatives. Also, safety evaluation conducted in terms of the range of field-of-view to ensure the easiness of field of view by various configurational difference between the vehicles. By the analysis results of such indicators, This study presents proposals for improvement in operating designated lane that low-speed-big-sized vehicles keep to the right lane, and high-speed-small sized vehicles keep to the left lane.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.5
• /
• pp.186-201
• /
• 2021

As autonomous driving technology advances, the accuracy of the vehicle position is important for recognizing the environments around driving. Map-matching localization techniques based on high definition (HD) maps have been studied to improve localization accuracy. Because conventional map-matching techniques estimate the vehicle position based on an HD map reference dataset representing the center of the lane, the estimated position does not reflect the deviation of the lateral distance within the lane. Therefore, this paper proposes a localization system based on the reference lateral position dataset extracted using image processing and HD maps. Image processing extracts the driving lane number using inverse perspective mapping, multi-lane detection, and yellow central lane detection. The lane departure method estimates the lateral distance within the lane. To collect the lateral position reference dataset, this approach involves two processes: (i) the link and lane node is extracted based on the lane number obtained from image processing and position from GNSS/INS, and (ii) the lateral position is matched with the extracted link and lane node. Finally, the vehicle position is estimated by matching the GNSS/INS local trajectory and the reference lateral position dataset. The performance of the proposed method was evaluated by experiments carried out on a highway environment. It was confirmed that the proposed method improves accuracy by about 1.0m compared to GNSS / INS, and improves accuracy by about 0.04m~0.21m (7~30%) for each section when compared with the existing lane-level map matching method.

• Journal of the Ergonomics Society of Korea
• /
• v.28 no.2
• /
• pp.9-16
• /
• 2009

The aim of this study was to evaluate the effects of the driving performance and workload according to changing driving environment and types of steering wheel. Twelve drivers who participated in this study consisted of two groups; six Japanese as the left-lane drivers who was accustomed to driving on left-hand side of the road, and six Europeans, Americans, and Korean as the right-lane drivers who was accustomed to driving on right-hand side of the road. They were asked to operate a driving simulator while using two different types of steering wheel (for the left-hand side driving and the right-hand side driving). During the experiment, a range of data were measured including driving performance, mental workload, and eye movements which were recorded in order to identify the amount of time looking towards the in-vehicle route guidance. Results indicated that the use of the steering wheel by parallel moving led to increase high attentional demand and worse glance behavior to traffic signs for the left-lane drivers. In the case of the right-lane drivers, the effects by changing driving direction were more effective than the types of steering wheel due to their habit or traits.