• Design & Manufacturing
• /
• v.8 no.2
• /
• pp.18-22
• /
• 2014

Two shot molding is one of the injection method which uses two materials or two color materials simultaneously in one mold. Two shot molding is good rate of productivity and economical because of no extra-progress necessary. The cowl grille is located in the bottom of wind shield glass and rolls as a passage of air inlet to inside of vehicle. It consists of body and seal. Firstly, the body is injected with PP. Next seal is extruded with EPDM and engineered and then assembled with body. These procedures lead high cost of production and the quality of part has problems. Therefore, it has effects on saving production cost and being a solution of the quality problems with the development of two shot molding cowl grille. It is guaranteed that two shot molding will be widely used in the vehicle parts industry afterwards.

• Design & Manufacturing
• /
• v.9 no.2
• /
• pp.30-33
• /
• 2015

In injection molding, many kinds of defects have occurred because of a characteristic of plastics injection molding. Weld line is one of the defects is formed when separated melt fronts recombine together during the mold filling stage. That is one of problems in injection molding. Weld lines in the appearance of plastics parts can deteriorate visible quality. And most importantly, the local mechanical strength in the weld line area can be significantly weaker. It could be one of the most problems for structural applications. In this study, the mold available two-shot-molding of same polymers have been designed, and a series of experiment about tensile strength in weld line area has been conducted using Taguchi's design of experiment to optimize injection molding conditions decreasing of weld strength and find out a factors affected weld strength in two-shot- molding.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.230-235
• /
• 2004

A new design based on the appropriate geometry of molded part and type of runner system under the optimal processing conditions was proposed to minimize the micro weld lines on the sub deco surface molded by two shot molding. Theoretical and experimental studies were conducted to examine the cause of the weld lines during the overmolding process in two shot molding. Various dimensions and geometries of substrate$(1^{st}shot)$ and the wall thickness of overmold$(2^{nd}shot)$ have been proposed to avoid the weld lines which are the most inevitable appearance defects occurred on the sub deco. The each design proposal was analyzed by mold flow analysis after part modeling. The analysis results were compared with molded part from mass production tool. It could be seen that from the analysis that the proper geometry of plastic part and type of runner system considering pressure drop under the optimal processing conditions were the most influential factors to avoid weld lines occured on the sub deco.

• Transactions of Materials Processing
• /
• v.18 no.2
• /
• pp.160-165
• /
• 2009

A Study on Effects of the Runner and the Gate of double shot injection molded Parts using CAE Double shot injection molding can inject two different materials or two different colors in the same mold in a injection molding process. Double shot injection molded parts can be characterized that the base part maintains strength and specified part can inject soft-material. It can reduce the production cost by single automatic operations. In this paper, we designed double shot injection mold for automobile emote control To inject secondary part, this part is used as an insert after external appearance of product is injected. CAE analysis was progressed gate location and runner size as variables. The analysis result is reflected in mold design process. As a result, it could solve problems which are generated in the conventional mold. Additionally, cost can be downed by reducing runner weight. As well as it could omit painting process because the surface of finished product is improved through new mold.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.95-100
• /
• 2004

Plastics is used to produce precise parts with an inclusion of a reinforcement material such as glass fiber or carbon fiber to improve the dimension accuracy. The plastic goods can be produced with inaccurate dimensions, low mechanical strength, or residual stress due to the over packing of cavity inside, if the filling balance of melt resin is not accomplished. To overcome this problem, it is necessary to design the runner system with the geometrical balance at the mold design stage. However, even if the balanced runner system is achieved, a severe filling imbalance is observed practically in a multi-cavity mold. In this study, experiments were performed with Taguchi method to achieve the filling balance in multi-cavity mold with a symmetric runner system, by the use of pure PA and PA with glass fiber 33%. The experimental results were investigated to understand the effect of related molding factors on the filling imbalance for two resins.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6047-6052
• /
• 2013

A cosmetic manufacturing process requires a mold that is inevitable for mass production. Cosmetic containers are one of major factors affecting the customer's purchase decision. In addition, the manufacturing cost in cosmetic container comprises a large portion of the entire product cost. Therefore, a mold satisfying the economical feasibility, aesthetics and functionality is necessary. Among the cosmetic containers, square shape containers have a tendency of having a short shot defect product. The square shaped cosmetic containers are mostly produced as a side gate shape on the two-plate molds. On the other hand, there are two disadvantages, such as gate trace and post processing requirement. The overlap-gateproposed in this study has the characteristics of intaglio gate cutting and no need for post processing. The delivery system of the overlap gate was simulated and compared with the side gate via Moldflow. The improvement in flow, frozen rate, density, and Air trap was confirmed. Based on the simulation results, the mold and performed injection molding was fabricated. In this study, the possibility of the mass production of high aesthetic and functionality cosmetic containers was verified.