• 한국구조물진단유지관리공학회 논문집
• /
• 제26권2호
• /
• pp.84-91
• /
• 2022

본 연구에서는 국내 내진설계기준에 의해 중간모멘트골조로 설계된 철골 모멘트접합부에서 면외방향 어긋남을 갖는 보가 접합부의 거동에 미치는 영향을 평가하였다. 기둥을 중심으로 보가 접합되는 형식에 따라 2가지 경우(단면접합 및 양면접합)와 각각의 경우에 대하여 4개 수준의 어긋남 각도(0°, 10°, 20°, 30°)를 조합하여 총 14개의 유한요소해석 모델을 구성하였다. 해석결과, 면외 어긋남을 갖는 대상 모멘트접합부는 국내 구조기준에 따른 중간모멘트골조의 성능수준을 만족하는 것으로 나타났다. 그러나, 면외 어긋남 각도가 커질수록 접합부 시스템의 하중저항능력이 감소하였다. 면외 어긋남 각도가 30°인 접합부에서 보-기둥이 직교된 접합부에 비하여 최대 하중은 약 13% 감소하였고, 층간 변위각 0.02 rad까지의 에너지 소산능력은 최대 26% 감소하였다. 또한, 어긋남 형상에 기인하여 접합부와 인접한 보 플랜지에서 응력이 비대칭으로 분포되며, 보 플랜지와 기둥 플랜지가 예각을 이루는 내측 플랜지(Inner Flange)에 응력이 집중되었다. 본 연구에서 고려한 보-기둥 접합에서는 어긋난 보에 의해 기둥의 축방향 회전에 미치는 영향은 미미하여 무시할 만 하였다.

• 한국항공우주학회지
• /
• 제35권5호
• /
• pp.390-396
• /
• 2007

본 연구에서는 새의 날개운동을 모사하기 위하여 스마트 재료를 이용한 플래핑 날개를 설계 및 제작하였다. 날개는 복합재료 프레임과 유연한 PVC 표피 그리고 표면 작동기로 구성되어 있으며, 주요 날개운동으로서 날갯짓, 비틀림 그리고 캠버 운동을 선정하였다. 날개의 캠버를 변화시키기 위하여 Macro-Fiber Composite를 표면작동기로서 적용하였으며, 압전-열 관계식을 이용하여 MFC의 구조 응답을 해석하였다. 양력과 추력을 동시에 측정하기 위하여 두개의 로드셀로 구성된 시험대를 제작하였으며, 공기역학적 특성을 평가하기 위하여 풍동실험을 수행하였다. 실험결과로부터 주요 양력은 기체의 전진속도와 피치각에 의존되며, 추력은 날갯짓 주파수에 의존됨을 확인하였다. 또한 MFC 작동기를 이용한 캠버효과를 통하여 정적조건에서 24.4%와 동적조건에서 20.8%의 충분한 양력증가를 확인할 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제13권2호
• /
• pp.1-7
• /
• 2006

본 논문에서는 솔더 레지스트(solder resist)의 두께와 코어의 물성에 따른 인쇄회로기판의 철의 크기와 형상에 대하여 연구하였다. 인쇄회로기판의 굽힘 변형은 적층되는 재료의 열팽창계수의 차이에 의해 발생한다. 따라서 굽힘 변형의 감소를 위해서는 열팽창계수의 차이가 작은 적층 재료를 사용하는 것이 필요하며, 구조 형상에서도 상면과 하면의 불균일성을 완화시킬 필요가 있다. 또한, 적층 재료에서 코어의 강성을 높여 점의 발생을 억제할 수 있다. 코어를 이루는 복합재료는 적층 순서와 섬유 각에 따른 물성 특성의 방향성에 따라 굽힘과 비틀림이 연성되는 현상을 보이며, 이와 같은 성질을 이용하면 휨을 제어할 수 있다. 본 연구에서는 2층으로 구성된 chip scale package (CSP) 기판의 휨에 대한 연구로, 실험 및 유한 요소해석 툴을 이용하여 개선 결과를 도출하였다.

• 한국강구조학회 논문집
• /
• 제18권2호
• /
• pp.203-211
• /
• 2006

본 논문에서는 집중 비틂모멘트와 등분포 비틂모멘트가 작용하는 박벽개보의 뒴구속에 대한 영향을 고려할 수 있는 새로운 유효비틀림계수를 제시한다. 상용 유한요소 프로그램의 알고리즘을 바꾸지 않고 순수 비틀림계수 대신에 제안된 비틀림계수를 직접 사용할 수 있다. 유도된 비틀림계수는 순수 비틀림과 뒴 비틀림에 의한 영향을 고려하며 순수 비틀림계수에 보정계수를 곱하여 산정한다. 순수 비틀림의 경우 유도된 계수는 순수 비틀림계수와 일치하게 나타났다. 순수 비틀림을 이용하여 본 연구에서 유도한 유효 비틀림계수는 Elhelbawey 등이 제안한 비틀림계수와 차이를 보여주고 있다. 또한, 유효 비틀림계수를 사용하여 구한 최대비틀림각을 이용하여 부재 내 에 발생하는 전단응력과 다른 연구자의 결과들과 비교, 검토한다.

• 대한토목학회논문집
• /
• 제26권1A호
• /
• pp.99-106
• /
• 2006

일축대칭의 단면특성을 갖는 T형 부재는 단면의 특성상 축방향 압축력으로 인하여 전체좌굴이 발생할 경우 휨-비틀림 좌굴이 지배모드가 된다. 인발성형 T형 부재의 휨-비틀림 좌굴거동을 실험적 연구를 통하여 알아보았다. E-glass/vinylester와 E-glass/polyester로 만들어진 2종류의 인발성형 부재가 사용되었으며, 보강층의 배치, 보강층의 두께, 구성물질의 부피비, 역학적 성질 등을 실험적으로 규명하였다. 좌굴실험에서 휨 및 비틀림에 대한 단순지지 조건을 만족시키기 위해서 knife edge를 사용하였으며, 3개의 potentiometer를 사용하여 실험체의 횡변위와 비틀림각을 측정하였다. 모든 실험체에 휨-비틀림 좌굴이 발행하였으며, 대부분의 실험체가 후좌굴 강도를 가지고 있음을 알 수 있었다.

• 한국운동역학회지
• /
• 제16권1호
• /
• pp.55-63
• /
• 2006

The purpose of this study is to prove the kinematical characteristics of Deff motion, the high bar performance, in terms of flying phases so that we can provide basic sources for improving gymnastic performance. To do this, we selected and analyzed the performance of two athletes who did Deff motion in the high bar competition of male artistic gymnastic in the 22nd Universiade 2003 Daegu. We drew the conclusions from the kinematical factors that were came out through analyzing three-dimensional cinematography of the athletes' movements, by using a high speed video camera. To make a successful performance, a performer releases the bar at a height of a high bar vertically and at a height of 82cm horizontally, and the flying performance should be made without moving forward, as maintaining the proper balance, in order to rise over 118cm high during the flying phase. When the performer is releasing the bar, an increase of the vertical speed in the center of the body and extension of a knee joint and a hip joint contribute to increasing a flying height. And when the moving body is twisted, leaning to left side is caused by the winding movement of a knee joint, which causes an unstable bar grasp. To grasp the bar stably, just before releasing the performer should gain propulsive force from twisting rotation through increasing the speed of shoulder rotation. And before the peak point, the performer should make sure of a body rotation distance over $164^{\circ}$ so that he or she can do an aerial rotary performance smoothly. When grasping the high bar, the center of the body should be above the bar and the angle of shoulder rotation should be maintained close to $540^{\circ}$ simultaneously. he high point performance(S1) has more speed on an ascending phase and less speed on a descending phase than the low point performance (S2). At the peak point, both the rotation angle of the body and that of the shoulder in high point performance are big as well. In conclusion, it is shown that a performer can make a jump toward the high bar easily with the body straight because the performer can hold the upper part of the body erect early in a descending phase.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.81-98
• /
• 2003

The purpose of this study is to closely examine kinematic characteristics by jump phase of Li Xiaopeng motion in horse vaulting and provide the training data. In doing so, as a result of analyzing kinematic variables through 3-dimensional cinematographic using the high-speed video camera to Li Xiaopeng motion first performed at the men's vault competition at the 14th Busan Asian Games, the following conclusion was obtained. 1. It was indicated that at the post-flight, the increase of flight time and height and twisting rotational velocity has a decisive effect on the increase of twist displacement. And Li Xiaopeng motion showed longer flight time and higher flight height than Ropez motion with the same twist displacement of entire movement. Also the rotational displacement of the trunk at peak of COG was much short of $360^{\circ}$(one rotation) but twist displacement showed $606^{\circ}$. Likewise, Li Xiaopeng motion was indicated to concentrate on twist movement in the early flight. 2. It was indicated that at the landing, Li Xiaopeng motion gets the hip to move back, the trunk to stand up and the horizontal velocity of COG to slow down. This is thought to be the performance of sufficient landing, resulting from large security of rotational displacement of airborne and twist displacement. 3. It was indicated that at the board contact, Li Xiaopeng motion made a rapid rotation uprighting the trunk to recover slowing velocity caused by jumping with the horse in the back, and has already twisted the trunk nearly close to $40^{\circ}$ at board contact. Under the premise that elasticity is generated without the change of the feet contacting the board, it will give an aid to the rotation and twist of pre-flight. Thus, in the round-oH phase, the tap of waist according to the fraction and extension of hip joint and arm push is thought to be very important. 4. It was indicated that at the pre-flight, Li Xiaopeng motion showed bigger movement than the techniques of precedented studies rushing to the horse, and overcomes the concern of relatively low power of jump through the rapid rotation of the trunk. Li Xiaopeng motion secured much twist distance, increased rotational distance with the trunk bent forward, resulting in the effect of rushing to the horse. 5. At horse contact, Li Xiaopeng motion makes a short-time contact, and maintains horse take-off angle close to vertical, contributing to the increase of post-flight time and height. This is thought to be resulted from rapid move toward movement direction along with the rotational velocity of trunk rapidly earned prior to horse contact, and little shave of rotation axis according to twist motion because of effective twist in the same direction.

• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• 공연문화연구
• /
• 제20호
• /
• pp.339-367
• /
• 2010

이 연구는 동서양 춤 동작의 원리를 비교하는 것으로 다리와 팔을 동시에 움직이는 즉, 한쪽 다리로 신체를 지탱하는 공통점을 지닌 수족상응(手足相應) 동작에 대하여 형태학적으로 접근하였다. 따라서 발레에서는 아라베스크(arabesque), 데벨로뻬(developpe), 아띠?드(attitude) 동작을 수족상응 동작의 예로 제시하였고, 한국무용에서는 탈춤의 외사위, 겹사위, 멍석말이 등을 포함한 민속무용의 수족상응 춤사위를 고찰하여 이들 춤에서 나타나는 형태학적 특징을 인종의 형질적 측면, 춤의 사상적 측면, 동작의 조형적 측면으로 탐색하였다. 그 결과 수족상응 동작의 형태에 나타난 양태는 다음과 같다. 첫째, 인류의 생태와 관련하여 인종의 형질이 동서양간 각각 다르기 때문에 무용수의 체격이나 체형은 춤의 형태를 다르게 발달시켰다. 따라서 발레는 긴 팔과 다리를 이용하여 신전하는 형태의 춤으로 수족상응 동작에서 신체의 한계선을 더욱 확장시킴으로써 우아하고 아름답게 보일 수 있도록 하였다. 반면 우리나라는 농업이 생업이었으므로 항상 땅과 가까이 한 탓에 체격이 왜소해졌고 이 때문에 춤사위는 '휘젓는 춤사위'와 '굴신걸음'으로 발전하여 대부분의 수족상응 동작에서도 이와 같은 형태를 취하고 있는 것으로 나타났다. 둘째, 동서양간의 자연관에 따라 동일한 형태의 수족상응 동작임에도 불구하고 발레는 천향(天香)을, 한국무용은 지향(地響)의 형태를 띠고 있다. 이것은 수족상응 동작의 원리가 땅을 지향(地向)하는 것임에도 불구하고 서양인의 사상과 추구하는 미적 가치가 천향(天向)을 지향(志向)하고 있기 때문인 것으로 추측된다. 셋째, 발레에서 미(美)의 초점은 외형으로 나타난 아름다운 동작 그 자체에 있다. 따라서 수족상응 동작에서도 신체가 완벽한 균형을 이룰 수 있도록 팔과 다리의 위치 및 각도를 규정하고 있다. 반면 한국무용의 수족상응 동작은 대부분 일상생활에서 나오는 자연스러운 움직임과 일의 능률을 올릴 수 있는 움직임에서 발전된 동작임으로 신체가 다소 불균형을 이루더라도 멋스러운 기교로 간주하고 있음을 고찰하였다.