• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.613-622
• /
• 2000

Watering operation for oyster mushroom growing houses is regarded as drudgery and time consuming farm operation for growers. Most of mushroom growing beds in oyster mushroom growing houses are designed as two-row with four floor beds, therefore the watering and ventilation between the bed floors are much difficult for farmers because of its structural design. The study aimed to reduce the watering operation and improve the mushroom growing environment through the humidification and air supply on mushroom growing beds. Results showed that appropriate size of nozzle is between 0.8~0.5ml/s for the humidification and higher than the 2.0ml/s for the watering. The optimum water supply pressure was regarded as between 1.0~2.0MPa and the uniform distribution of droplet on the bed showed on air flow speed of 14m/s. The prototype was equipped with twin nozzle with. the humidification nozzle of 0.85ml/s and watering nozzle of 5.0ml/s, and the air blast fan with the air speed of 10m/sec in each air spout. In the field test in a practical scale mushroom growing house, it was well operated dependant on the set desire by a electric control unit. The machine can be practically used as air blast watering and air blast humidification for oyster mushroom growing farms without manual.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.125-130
• /
• 2001

Experimental and analytical researches have been conducted on the twin-fluid atomizers for better droplet breakup during the past decades. But, the studies on the disintegration mechanism still present a great challenge to understand the drop behavior and breakup structure. In an effort to describe the aerodynamic behavior of the sprays issuing from the internal mixing counter-swirling nozzle, the spatial distribution of axial (U) radial (V) and tangential (W) components of droplet velocities are investigated across the radial distance at several axial locations of Z=30, 50, 80, 120 and 170mm, respectively. Experiments were conducted for the liquid flow rates which was kept constant at 7.95 g/s and the air injection pressures were varied from 20 kPa to 140 kPa. Counter-swirling internal mixing nozzles manufactured at angles of $15^{\circ},\;30^{\circ},\;45^{\circ}$ and $60^{\circ}$ the central axis with axi-symmetric tangential-drilled holes was considered. The distributions of velocities and turbulence intensities are comparatively analyzed. PDPA is installed to specify spray flows, which have been conducted along the axial downstream distance from the nozzle exit. Ten thousand of sampling data was collected at each point with time limits of 30 second. 3-D automatic traversing system is used to control the exact measurement. It is observed that the sprays with all swirl angle have the maximum SMD for on air injection pressure of 20 kPa and 140 kPa with centerline, respectively. The nozzle with swirl angle of $60^{\circ}$ has vest performance.

• 대한기계학회논문집B
• /
• 제30권12호
• /
• pp.1236-1242
• /
• 2006

The local heat flux of spray cooling in the film boiling region were experimentally investigated for the spray region of $D_{max}$ = $0.005{\sim}0.03m^3/(m^2s)$. A twin-fluid full cone spray nozzle was employed for the experiment and the distributions of droplet flow rates were obtained for air-water full cone sprays. A stainless steel block was cooled down from initial temperature of about $800^{\circ}C$ by full cone spray. In the region near the stagnation point, it was found that the experimental data are in good agreement with the results predicted from the correlations between the local heat transfer and the local droplet flow rate proposed in the previous report. However, it was found that the experimental data of $D_r$ > $0.01m^3/(m^2s)$ are a little smaller than the results predicted from the correlations.

• 한국추진공학회지
• /
• 제3권1호
• /
• pp.9-14
• /
• 1999

작동조건이 두개의 공기충돌형 연료분사장치로부터 분사되는 이중분무 특성에 미치는 영향을 공연비 1.36∼3.54의 범위에서 실험적으로 수행하였다. 물과 질소가스가 실험유체로서 사용되었다. 분무 액적의 분포특성은 질량분포와 순간영상 촬영법에 의하여 측정되었다. 실험적 결과는 ROA(축방향에 대한 반경방향 공급압력비)의 증가에 따라 질량분포곡선의 최대값은 낮아지면서 더 넓은 영역에 걸쳐 분포하였으며 공급유체의 증가에 따른 질량중심점의 위치는 변화가 없었다. 노즐간격 증가는 간섭영역에서의 질량분포에는 커다란 영향을 미치지는 않았으나 더 넓은 영역에 걸쳐 분포하려는 특성을 보여주었다. 또한, ROA 비가 증가할수록 충돌중심점 근처에서 간섭의 영향은 작아짐을 중첩법을 이용하여 비교함으로서 잘 알 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.253-256
• /
• 2003

65마력급 UAV용 초소형 터보샤프트 엔진의 코어를 55lbf급 터보제트 형식으로 개조 개발하였다. 터보샤프트 엔진의 동력발생기와 동일한 유량 특성을 갖는 배기 노즐을 부착함으로써 코어 엔진은 완제 엔진과 완전히 동일한 기계적, 공력적 특성을 보유하고 있다. 엔진 출력은 축 마력 대신 비교적 계측이 용이한 추력으로 나오기 때문에 터보샤프트 엔진의 성능과 수명을 좌우하는 코어의 검증 시험 용도로 매우 유용하다. 뿐만 아니라 코어 엔진은 그 자체로 하나의 터보제트엔진으로 추력이 필요한 소형 비행체의 추진기관으로 직접적인 활용이 가능하다.